Panasonic DLP Based Projector PT-D5600U PT-D5600UL PT-DW5000U PT-DW5000UL Operating Instructions

							41
Indication of lamp monitor
This projector is equipped with 3 indicators to show when a lamp needs replacement or there is an abnormal
internal temperature. These lamps flash or light up to indicate a problem.
Turn the power off and follow the steps below.
Temperature monitor 
(TEMP) indicator Lamp 1 monitor (LAMP 1) Lamp 2 monitor (LAMP 2) Power indicator
• To solve any problems that the TEMP and LAMP monitor show, first turn the power off by
following the steps on pages 23, 24.
• If the power indicator blinks in red (3 times), the projector has malfunctioned. Please consult your
dealer.Attention
Name of monitor
lampLamp
indicationInformation
High temperature
inside. (WARNING)
• Check if the
ventilation port is
blocked.
• Is the room air
temperature too high?
• Is the air filter clogged
with dust?
Warm-up status 
• Did you turn on the
power when the
ambient temperature
was low 
(approx. 0 °C)? 
Checkpoint
• Wait about five minutes in the
current status.
• Install the unit in a location
having an ambient
temperature from 0 to 45 °C. 
• Remove the object that is
blocking the ventilation port.
• Move the projector to a
temperature of 0 to 45 ˚C and
the humidity of 20 to 80 % (no
condensation).
• Turn off the MAIN POWER
switch using the procedure on
page 24 and clean the air filter
(refer to page 42).
Lighting in
red
(lamp unit
ON)
Remedial measure
Blinking in
red
(1 time)
Blinking in
red
(2 times)
The filter is clogged.
High temperature
inside
(Standby condition)
Blinking in
red
(3 times)Cooling fan has
been stopped.
• Turn off the main power supply
(MAIN POWER) switch in the
procedure shown on page 24
and consult the distributor.
• This lamp monitor lights up
when the lamp unit used hours
have reached 1 300 hours 
(3 800 hours when long life
lamp units are used). Request
the dealer to replace the lamp
unit.
• Wait until the lamp has cooled
off, and then turn on the
power.
• Did you notice a
“REPLACE LAMP”
message on the
screen when turning
on the projector
power supply?
• Did you turn the power
back on immediately
after turning it off?
• Turn off the MAIN POWER
switch using the procedure on
page 24 and consult the
dealer.
• Some error has
arisen in the lamp
circuit.
• Check for fluctuation
(or drop) in the source
voltage.
Indicates the time
for replacing the
lamp unit.
Error is detected in
the lamp or lamp
power.
Lighting in
red
Blinking in
red
(3 times)
Temperature 
monitor
TEMP
Lamp monitor
LAMP1       LAMP2 
						

							42
Cleaning and replacement of air filter
If too much dust accumulates on the air filter, [AIR FILTER] appears at the lower left of the screen, and the
temperature monitor (TEMP) will blink once. If even more dust is allowed to accumulate, the temperature inside the
main unit will rise, the temperature monitor (TEMP) will blink twice, and the power is turned off.
Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector
operation.
It appears only for 30 seconds within 3 minutes after the power is turned on. It disappears if any of the buttons
on the rear side of the main unit or on the remote control is pressed.
Procedure of cleaning
Turn off the main power and remove the power plug from the receptacle.
Turn off the main power supply observing the procedure (Powering off the projector) on page 24 and then
remove the power plug.
Dismantle the air filter.
There are two air filters, one at the left and one at the right.
Use your finger to pull the air filter tab toward you, and remove it from the main unit.
Set the air filter.
Set the air filter in the reverse order to step  .
Clean the air filter.
Suck off deposited dust with a vacuum cleaner.
• Do not to suck in the air filter itself.
• Do not rinse off the air filter with water.  Doing so will impair the filter’s ability to provide
protection from dust.Attention
• Fit the air filters into place with the filter material facing the back.
(The left and right filters have the same shape.)
• The air filter must be fitted in place when using the projector.
Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector,
causing failure.Attention
• If cleaning cannot remove the dust completely, then it is a sign to replace the air filter. Consult the
dealer. In addition, when the lamp unit is replaced, also replace the air filter.
• Be absolutely sure to use the air filter specifically designed for use with the projector.
Note
Air filter 
						

							43
Replacing the lamp unit
Precautions on lamp unit replacement
Remove the power plug and confirm that the surroundings of the lamp unit have cooled off.
Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled,
explosion might result.
A used lamp unit may burst if it is handled violently.
For disposition of used lamps, request an industrial waste disposal contractor.
Do not reset the cumulative time, except when the lamp unit has been replaced with a new unit.
If you continue to use a lamp after the replacement time, the lamp may break.
Phillips screwdriver is necessary when replacing a lamp unit.
Take care not to slip your hand when using a screwdriver.
• A lamp unit is an optional part. Contact the dealer.
Replacement lamp unit model No.: ET-LAD55 (single bulb), ET-LAD55W (double bulbs)
Rating: 300W
Long life lamp unit model No.: ET-LAD55L (single bulb), ET-LAD55LW (double bulbs)
Rating: 160W
• Other lamps than specified above cannot be used. Be sure to use the specified lamp.Attention
Timing of lamp unit replacement
The lamp used for the light source has its due life. The life of light source lamp used in the main unit is 1 500
hours1(when “LAMP POWER” is “HIGH” and “LAMP SELECT” is “DUAL”). However, it may happen that the
lamp becomes dead (will not light) by the time of 1 500 hours1depending on the characteristics of individual
lamps and working conditions (lamps may reduce their life affected by the times of lighting and the intervals
between previous lighting and next lighting). Therefore, it is strongly recommended for the user to keep a spare
bulb.
If your lamp unit is not replaced after 1 300 hours
2(with “LAMP POWER” set at “HIGH”), power supply will be
turned off automatically at the time of 1 500 hours1, entering a standby state. After 1 500 hours1of initial
lighting, power supply is turned off automatically about 10 minutes later, entering a standby state even if it is
turned on again.
Indication after 1 300 hours2(with “LAMP POWER” set at “HIGH”)
When lamp unit used hours have reached 1 300 hours2, lamp monitor
(LAMP1 or LAMP2) light up including standby state.
Further, an on-screen indication will appear for about 30 seconds as
shown in the diagram on the left, recommending replacement of lamp unit.
(The indication on the left diagram will disappear after about 30 seconds or
when either control button on the rear of main unit or remote control button
is operated.)
After the time of 1 500 hours
1, the on-screen indication will not disappear
unless the menu (MENU) button is operated.
REPLACE LAMP
1 This time period is 4 000 hours when long life lamp units are used.
2 This time period is 3 800 hours when long life lamp units are used.
WARNING!
When replacing the lamp, allow it to 
cool for at least one hour before 
handling it. 
						

							44
Replacing the lamp unit
Lamp unit replacement steps
• After 1 500 hours (4 000 hours when long life lamp units are used) of operating the same lamp, it
is only possible to operate the unit for approximately 10 minutes. Steps  to  must be
completed within 10 minutes.Attention
Turn the power off by following the steps on page 24, remove the power plug and
confirm that the surroundings of the lamp unit have cooled off.
Check that the fan has stopped running.
Have a Phillips screwdriver ready ahead of time.
Remove the screw securing the lamp unit
cover, and then slide the lamp unit cover
a little toward the left, and remove it.
Remove the two screws securing the
fan unit.
Lamp unit cover
Open the fan unit as shown in the
figure.
Remove the screws securing the lamp
units (two for each unit), take hold of
the handles, and remove the lamp units.
Install the new lamp unit.
Use a Phillips screwdriver to securely
tighten the 2 lamp unit fixing screws
(two for each unit).
Lamp unit 2
Handle
Lamp unit 1 Lamp unit
Fixing screws
Secure the two screws for securing the
fan unit tightly.
Slide the cover a little toward the right,
and secure it using the screw for
securing the lamp unit cover tightly.
• Firmly install the lamp unit and lamp
unit cover. If not installed firmly, a
protection circuit will function and the
power will not be turned on.Attention
• The lamp units are constructed in such
a way that the screws in steps  and
will not fall through completely.Note
Caution
The lamp unit will be hot after it has
been used.
You might get burned if you touch it while it is
still hot. 
						

							45
Insert the power cord plug into the wall outlet and then
press the MAIN POWER switch.
Press the “ I ” button so that a picture is projected onto
the screen.
Press the “MENU” button to display the MAIN MENU
screen, and then press the  and  buttons to move
the cursor to select “OPTION2”.
Press the “ENTER” button to display the “OPTION2”
screen, and select “SYSTEM INFORMATION” with the 
and buttons.
Press the “ENTER” button.
The SYSTEM INFORMATION screen will be displayed.
Press and hold the “ENTER” button on the projector or
the remote control for approximately 3 seconds.
An item “LAMP TIME RESET” will be added.
Select the lamp which has been replaced with the  and
buttons. 
LAMP1: Replace the LAMP UNIT 1
LAMP2: Replace the LAMP UNIT 2
Press the ENTER button, and when the “LAMP TIME
RESET” display flashes, press the ENTER button again.
The used hours of the specified lamp unit will be reset to zero.
When more than one lamp has been replaced, repeat the procedure from
step .
• If the power does not turn on even after turning the MAIN
POWER switch “I”, turn the MAIN POWER “O”, confirm that
the lamp unit and door are installed correctly, and turn on
again.Attention
MENU
PICTURE
ADVANCED MENU
OPTI0N2
TEST PATTERN OPTION1 POSITION
LANGUAGE
LAMP TIME RESET
LAMP1
LAMP2
  LAD55
  LAD55L   LAD55
1433h
0h
1100h
0h   LAD55L
SYSTEM INFORMATION
ROM VERSION
          HIGH
200h
        TOTAL
300h
LAMP2 LOW SET RUNTIME
300h
LAMP1 LOW
100h
100h 1. 00. 00
• When the “LAMP TIME RESET” display flashes, the lamp
time reset can be canceled by pressing the MENU button.
• The used hours of the lamp units can also be reset to zero
by taking the following action instead of steps  to  .
When lamp unit 1 has been replaced:
In the standby mode, press the number buttons in the
sequence of 737381, and then press the ENTER button.
When lamp unit 2 has been replaced:
In the standby mode, press the number buttons in the
sequence of 737382, and then press the ENTER button.
When the used hours have been reset, the lamp monitor
(LAMP1/LAMP2) will flash for 3 seconds.Note 
						

							46
Using Web Browser Control 
Accessing from the Web browser
Start the web browser on your PC, then
enter the IP address which was set in
the projector.
Enter “user1” in the user name field,
then enter the password in the
password field.
The default setting is “panasonic” (all lower case). If
you have changed the password, enter the new
password here. 
The host name set in the projector is displayed in
the “Realm” field.
Click [OK]. 
The Basic Control page is displayed.
Password change page
Click [Change password].
• Avoid activating two or more Web browser
simultaneously to work out setting or
control actions.
• Change the password first of all.Note This projector has networking functions which allow it to be controlled through a web browser on a PC. 
The controlled items are:
• Projector’s settings and adjustment
• Projector’s status display
• Transmission of a E-mail message when the projector has a problem
Old password input field
New password input field
New password input field
(re-enter for confirmation)
Button for executing password change
Button for erasing all entered characters 
						

							47
Basic control page
This page is the first page displayed when the projector is accessed through a web browser.
To move from another page, click [Projector control], then [Basic control]. 
E-mail set up button
Click this item, and an E-mail setting page appears.
Monitor information button
Click this item, and the status of the projector is displayed.
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
Pressing these buttons controls the projector and updates the on-screen
description on the right of the control page when control is finished.
On-screen status is displayed, even if
the on-screen of projector is set to off.
Temporary stop of video
Lens adjustment
Test pattern display
This button updates the on-screen
description on the right of the control
page with the latest information.
Control button
Click this item, and a
projector control page
appears.
OSD
(On-screen Display) display/non-
display
Power On/Off control 
Shutter control
Use these to select the input signals.
Signal System Switching
Network set up button
Click this item, and a network set up page for IP address and
other items appear.
Change password button 
						

							48
Using Web Browser Control 
Error information page
When  is displayed on the status information screen, click it to display the error details.
• Depending on the nature of the error, the projector may be placed in the standby mode for its own
protection.Note
OK: Normal operation
FAILED: Occurrence of trouble
Monitor information page
Click [Projector control], then [Status information] to display the Status information page.
This page displays the projector statuses established for the items shown below.
Displays the input switching status.
Displays temperature of projector’s
intake air.
Displays temperature inside the
projector.
Displays the lamp1 lit hours.
Displays the lamp2 lit hours.
Displays used hours of the projector.
Displays self-diagnosis information.
Displays the type of projector.
Displays the firmware version of the
projector main unit.
Displays temperature around the lamp.  
						

							49
When [FAILED] has appeared for an item
Parameter
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP
TEMPERATURE
LAMP REMAIN TIME
LAMP STATUS
SHUTTER
AIR FILTER
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP 
TEMP. SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
Description
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is high. It may be that the projector is
being used where the ambient temperature is high such as near a heating
appliance.
The input air temperature is too high. It may be that the projector is being
used where the ambient temperature is high such as near a heating
appliance.
The temperature near the lamp has risen very high.
Something may be blocking the exhaust vent.
The lamp runtime has exceeded the prescribed cumulative time, and it is
now time to replace the lamp.
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
Trouble has occurred in the shutter circuitry. Consult your dealer.
Too much dust accumulates on the air filter.  
Turn off the MAIN POWER switch using the procedure on page 24 and
clean the air filter (refer to page 42).
Trouble has occurred in the temperature detection sensor inside the
projector. Consult your dealer.
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
Trouble has occurred in the temperature detection sensor around lamps.
Consult your dealer.
The backup battery has been run out. Consult your dealer.
Trouble has occurred in the air volume sensor. Consult your dealer.
Trouble has occurred in the color wheel or the color wheel drive circuit.
Consult your dealer.
The user can modify the threshold temperature for sending
temperature warning mail. If the temperature rises above the set
value, control sends temperature warning mail.
E-mail setup page
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be
sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then [E-mail
set up] to display the E-mail setup page.
Select “Enable” to use the E-mail
function.
Enter the IP address or server name of
the E-mail server (SMTP). The DNS
server must be set if the server name is
entered.
Enter the E-mail address of the projector.
(maximum 63 characters)
The user can enter the location of, for
example, the installed projector so that
the recipient may easily identify the
originator of the E-mail.
(maximum 63 characters)
The user can modify the minimum time
interval of temperature warning mail.
The default value is 60 minutes.  In this
case, the user cannot send another mail
for 60 minutes after sending previous
temperature warning mail even the set
warning temperature is reached again.
(Continued on next page) 
						

							50
Using Web Browser Control 
Enter the E-mail address to which the E-
mail is to be sent when two E-mail
addresses are going to be used. Do not
enter it when the second E-mail address
is not going to be used.
Check these boxes when E-mail is to be
sent periodically to two E-mail
addresses. E-mail will be sent at the
times and on the days checked.
E-mail setup page (Continuing)
Select the conditions for sending E-mail.
ERROR:
an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp
service time has reached the value set in
the field.
INPUT AIR TEMPERATURE:
intake air temperature has reached the
value set in the field.
Periodic warning interval setting (e-mail
is sent on the checked days of the
week/times)
Enter the E-mail address of your desired
recipient.
Select the conditions for sending the second E-mail.
ERROR:an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp service time has reached the value set
in the field.
INPUT AIR TEMPERATURE: intake air temperature has reached the
value set in the field.
Button to update settings
• Only alphanumeric characters, “.”, “_”, “-”, or “@” are available to set an e-mail address.
Note