Panasonic Dmc Fz2 Operating Instructions Manual

							Preparation
21
Attaching the Strap
1To remove the cover, gently squeeze 
both sides of the cover as shown in 
picture 1.
2Rotate the plastic part of the metal 
fitting in the direction of the arrow.
 Please attach the plastic part to the 
metal fitting again if it is detached.
3Pass the metal fitting through the 
eyelet of the camera.
4Rotate the plastic part of the metal 
fitting to the opposite direction until it 
is locked.
5Move the cover in the direction of the 
arrow, and attach it firmly.
 Be sure to move the cover entirely until 
it is attached firmly.
6Attach the strap to the other side of 
the camera in the same way.
1
2
3
5
4
FZ2-PP.book  21 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
22
Attaching the Lens Cap
When you turn the camera [OFF] or draw 
back the lens, attach the supplied lens cap to 
protect the surface of the lens.
1Pass the top of the string through the 
lens cap.
2Pass the opposite side of the string 
through the circular part of the string.
3Pull in the direction of the arrow.
4Pass the top of the lens cap string 
through the strap eyelet as shown in 
the picture.
5Attach the lens cap.
 Remove the lens cap before turning on the 
camera in the recording mode.
 Even when the lens hood is attached, you 
can attach the lens cap without the string.
1
2
3
4
5
FZ2-PP.book  22 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
23
Using the LCD Monitor/Viewfinder
Every time you press the [DISPLAY] button, 
the display of the LCD monitor/Viewfinder 
changes as shown below.
[Menu display] [In multi/zoom playback]A LCD monitor
B Viewfinder
[In recording]
[In playback]
 When the LCD monitor is displayed, the Viewfinder turns off. (and vice versa)
DISPLAY
1600PICT.SIZEQUALITY
REC1
/
4
W.BALANCE 
SETUP
SELECT SET
EXITMENU
AE MODEPAUTOAE1600PICT.SIZEQUALITY
REC1
/
4
W.BALANCE 
SETUP
SELECT SET
EXITMENU
AE MODEPAUTOAE
1600P1600P
100-0001100-0001100-0001100-0001
F2.81/2001/2000PF2.81/2001/2000ISO100PISO10010:00 NOV.1.200310:00 NOV.1.200310:00 NOV.1.200310:00 NOV.1.2003
FZ2-PP.book  23 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
24
The Shutter Button 
(Pressing halfway/Pressing fully)
The shutter button is activated in 2 steps: 
“pressing halfway” and “pressing fully”.
Pressing halfway 1
 Focus and exposure are locked.
Pressing fully 2
 The picture is captured. In motion image 
mode, the recording starts.
 You can adjust volume of the operational sound in the menu. (P83)
 If you press the shutter button fully in a single stroke, the captured picture may 
appear shaken or unfocused. (The camera may be moved during capturing)
FZ2-PP.book  24 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
25
The Mode Dial
You can choose a desired mode by the mode dial.
: Playback (P64)
Playback recorded images.
: Simple mode (P31)
Menu options are minimized and many settings are preset. This is a fast and easy 
way for beginners to start using the camera and become familiar with its many 
features.
P/A/S 
: Program AE (P29)
The shutter speed and the aperture value are automatically adjusted. In addition, 
more settings can be adjusted.
: Aperture-priority AE (P45)
The shutter speed is adjusted automatically, according to the aperture value you 
set.
: Shutter-priority AE (P46)
The aperture value is adjusted automatically, according to the shutter speed you 
set.
: Macro mode (P47)
When you take pictures from a distance closer than 3.94 feet (120 cm) (Tele), set 
the camera in macro mode. This allows you to get closer to the subject up to 
0.16 feet (5 cm) (Wide).
: Portrait mode (P48)
This mode allows you to easily achieve the depth of focus effect. The subject stands 
out in front of an unfocused background.
FZ2-PP.book  25 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
26
: Sports mode (P49)
When taking pictures of outdoor sports, this mode lets you capture still action 
photos easily.
: Panning mode (P50)
Panning is a technique of moving the camera tracking a subject in motion.
Using a slower shutter speed when tracking a subject, you can sharply photograph 
a subject in motion while blurring the background.
: Night portrait mode (P51)
When you take pictures of your friends in front of beautiful night illumination 
scenery, this mode allows you to get the appropriate exposure for your subject as 
well as the background by using flash and slow shutter.
: Motion images mode (P33)
Use this mode when recording motion images.
FZ2-PP.book  26 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
27
Operating the Menu
By operating the menu, you can set the 
settings of REC or playback mode. You can 
also set the date and time, the operational 
sound and various other settings. Follow 
these instructions.
[Preparation]
 Set the mode dial to the recording mode 
(except for [ ]) or the playback mode.
1Press the [MENU] button.
 If you set the mode dial to the recording 
mode, the REC menu is displayed; if 
you set it to the playback mode, the 
playback menu is displayed.
2Press 1.
3Press 3/4 to choose the item.
4Press 2/1 to set the item.
5Press the [MENU] button.
 The menu will disappear.
1,5
2,3,4
1600PICT.SIZEQUALITY
REC1
/
4
W.BALANCE 
SETUP
SELECT SETEXITMENU
AE MODEP
MONITOR
AUTOAE
BEEPPOWER SAVE
REC
MONITOR
SETUP1
/
2
SELECT SETEXITMENU
AUTO REVIEW
2 1
OFF
2MIN.
2MIN.
2MIN.
BEEPPOWER SAVE
RECSETUP1
/
2
SELECT SETEXITMENU
AUTO REVIEW
3
MONITOR
BEEPPOWER SAVE
RECSETUP1
/
2
SELECT SETEXITMENU
AUTO REVIEW
4
OFF
OFF
FZ2-PP.book  27 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Preparation
28
Setting the Date/Time (Clock Set)
If the message [PLEASE SET THE CLOCK] 
appears, set the date and time.
You can go to the setup menu by pressing the 
[MENU] button while the message is 
displayed.
You can set the year from 2003 to 2099. The 
24-hour system is used.
1Press the [MENU] button.
2Press 1 to make the setup menu 
appear.
 In simple mode, skip this step.
3Press 3/4 to select [CLOCK SET], 
and then press 1.
4Press 3/4/2/1 to set date and time, 
and then press 1.
5Press 3/4 to select [M/D/Y], [D/M/Y] 
or [Y/M/D].
6Press the [MENU] button 2 times.
 The menu will disappear.
7Check if the date/time setting is 
displayed correctly, after turning the 
camera [OFF] and [ON].
 It is possible to print the recording date.
When using the [SD Viewer for DSC] in the supplied CD-ROM, you can print with 
the recording date by setting its position on the picture. For further information 
(software installation), read the supplied operating instructions for PC connection.
 When you want digital printings with the recording date, be sure to order the 
printing of the date. For further information, ask a photo studio, a store, etc. 
Depending on the store, it may not be printed.
 After a fully charged battery is installed in the camera for at least 1 hour, the time 
and date will be held for approximately 24 hours if the battery is removed. If the 
battery was not fully charged the time may not be retained properly. If the time/
date setting is lost please reset it.
7
1,62,3,4,5
CLOCK SET
M/D/Y
4,5
NOV10:00
12003.
.
CLOCK SET
LANGUAGE
REC
NO.RESET
SETUP2
/
2
RESET
3
ENG
SELECT SETEXITMENU
SELECT SETEXITMENU
FZ2-PP.book  28 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Recording images (basic)
29
Recording images (basic)
Taking Pictures
By only pressing the shutter button, the 
exposure (shutter speed and aperture value) 
will be automatically adjusted and the picture 
will be taken. (Refer to P45 for 
aperture-priority. Refer to P46 for 
shutter-priority.)
[Preparation]
 Insert the card. (P15)
 Set the power switch to [ON]. (P17)
1Set the mode dial to [P/A/S]. (P25)
2Press the [MENU] button.
3Press 3/4 to select [AE MODE].
4Press 2/1 to set to [P].
5Press the [MENU] button.
 The menu will disappear.
6After centering the subject in the 
AF area1
 on the LCD monitor/
Viewfinder, press the shutter button 
halfway
.
 When the focus is adjusted, the focus 
indication [¥]2 appears.
 When the focus indication flashes, the 
focus is not adjusted. Press the shutter 
button halfway to adjust the focus 
again.
 The shutter speed and the aperture 
value3 are automatically adjusted 
and displayed on the LCD monitor/
Viewfinder.
 When the subject is out of the AF area, 
use the AF/AE lock. (P55)
7Press the shutter button fully to take 
the picture.
 After taking a picture, when the auto 
review (P82) is set to [1SEC.]/[3SEC.], 
the picture is displayed on the LCD 
monitor/Viewfinder for about 1 or 
3 seconds.
6,7
1
2,5
3,4
REC1
/
4SETUP
3,4
W.BALANCE AUTO
PICT.SIZE
AE MODE
QUALITY
AS
1600
AEP
SELECTSET
EXITMENU
6
1600
1/25
P
F2.8
FZ2-PP.book  29 ページ  ２００３年９月２６日　金曜日　午後１２時１分 
						

							Recording images (basic)
30
 If the shutter button is pressed all the way, at once, the camera may not focus 
properly. An alternative to first pressing halfway is to enable Continuous AF.
 Even when the focus indication is displayed and the focus is properly adjusted, it 
will be cancelled if you release the shutter button.
Press the button halfway again.
 When power saving time is set, if you do not operate the camera for a while, it is 
automatically turned off at the set time. To operate the camera again, press the 
shutter button or turn the power switch first to [OFF] and then to [ON]. (P84)
 The brightness of the LCD monitor/Viewfinder may differ from that of the recorded 
pictures. In particular, when taking pictures in dark places with a long time 
exposure, darkness appears on the LCD monitor/Viewfinder, but the recorded 
pictures are bright.
 If the exposure is not properly set, the color of the aperture value and the shutter 
speed on the LCD monitor/Viewfinder becomes red.
 In the following cases, the focus may not be adjusted properly.
1 Recording a scene including subjects both near and far
2 Recording a scene through a dirty pane of glass
3 Recording an illuminated subject
4 Recording in darkness
5 Recording a moving subject
6 Recording a subject with little contrast
7 Recording with jitter
 We recommend that you set the clock setting again before taking pictures.
 When the brightness of the LCD monitor/Viewfinder changes such as while 
zooming or panning, you may hear a click sound from the lens or the image on the 
LCD monitor/Viewfinder may change suddenly; this is not a malfunction. The 
sound is caused by the camera automatically adjusting the aperture value.
 When pressing the shutter button halfway, the LCD monitor/Viewfinder may 
become dark or bright for a moment; this is not a malfunction. This arises from 
adjusting the aperture value.
 When the power is [OFF], this camera chatters if it is shaken. However, this is not 
a malfunction.
About jitter To prevent jitter, be careful when you press the shutter button.
 When the jitter alert 1 appears, we recommend you use a tripod.
1600P
F2.8 1/8
FZ2-PP.book  30 ページ  ２００３年９月２６日　金曜日　午後１２時１分