Panasonic Dmp Bdt210 Owners Manual

							Connections & Settings
11VQT3B58
Precautions of Wireless LAN connectionThe following limits are in place regarding the usage of this unit or 
Wireless LAN adaptor. You must be aware of these limits before using 
these devices.
Panasonic will in no way be responsible for any incidental damage which 
may arise due to a failure to obey these limits, or to any condition of use or 
disuse of these devices.
≥Data transmitted and received over radio waves may be 
intercepted and monitored.
≥ This  unit or Wireless LAN adaptor  contain delicate electronic 
components.
Please use these devices in the manner in which it was intended and 
follow the following points:
– Do not expose these devices to high temperatures or direct sunlight.
– Do not bend, or subject these devices to strong impacts.
– Keep these devices away from moisture.
– Do not disassemble or alter the device in any way.[BDT210]
THE FOLLOWING APPLIES IN THE U.S.A. AND CANADAThis device complies with Part 15 of FCC Rules and RSS-Gen of IC 
Rules.
Operation is subject to the following two conditions: 
(1) This device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired 
operation of this device.
Contains FCC ID: VPY-LBSJ
Contains IC:772C-LBSJ
This transmitter must not be co-located or operated in conjunction with 
any other antenna or transmitter.
This product is restricted to indoor use due to its operation in the 5.15 to 
5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency 
range 5.15 to 5.25 GHz to reduce the potential for harmful interference to 
co-channel Mobile Satellite systems. High power radars are allocated as 
primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. 
These radar stations can cause interference with and/or damage this 
product.
This equipment complies with FCC/IC radiation exposure limits set forth 
for an uncontrolled environment and meets the FCC radio frequency (RF) 
Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC 
radio frequency (RF) Exposure rules. This equipment has very low levels 
of RF energy that it deemed to comply without maximum permissive 
exposure evaluation (MPE). But it is desirable that it should be installed 
and operated keeping the radiator at least 20cm or more away from 
person’s body (excluding extremities: hands, wrists, feet and ankles).
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 
communications.
However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC caution: To maintain compliance with FCC regulations, shielded 
interface cables must be used with this equipment. Operation with 
non-approved equipment or unshielded cables may result in interference 
to radio and TV reception. Any changes or modifications not approved by 
the party responsible for compliance could void the user’s authority to 
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including 
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
THE FOLLOWING APPLIES ONLY IN CANADA.This Class B digital apparatus complies with Canadian ICES-003.
DMP-BDT110_115_210_VQT3B58_eng.book  11 ページ  ２０１０年１２月２日　木曜日　午前９時１８分 
						

							12VQT3B58
STEP 4 : Connecting to 
an AC power source
≥This unit consumes a small amount of AC power (“Quick 
Start”: “Off”, approx. 0.1 W) even when turned off. In the 
interest of power conservation, if you will not be using this 
unit for an extended period of time, it can be disconnected.
STEP 5 : Settings
After connecting your new player for the 1st time and 
pressing the power button, a screen for the basic settings 
will appear.
PreparationTurn on the television and select the appropriate video 
input on the television.
1Press [ ÍPOWER].
Setup screen appears.
If this unit is connected to a Panasonic TV (VIERA) 
supporting HDAVI Control 2 or later via an HDMI cable, 
then setting information on the TV such as “On-screen 
Language” is acquired by this unit.
2Follow the on-screen instructions and 
make the settings with [ 3,4] and press 
[OK].
After completing “Easy Setting”, you can perform “Network 
Easy Setting”.
	≥ You can perform this setup anytime by selecting “Easy Setting” in the 
Setup menu. ( >33)
Touch Free Sensor  
[BDT210]By setting “Sensor” in “Touch Free Sensor” to “On”, you can open or close 
the tray just by waving your hand over the TOUCH-FREE SENSOR on the 
upper side of the unit. (This will also work when in stand-by.) 
≥Be aware that the TOUCH-FREE SENSOR may function unintentionally 
in the following cases:
– When your hand or arm, an object, a small child, or a small animal 
comes close to the upper part of the unit
– When an object is placed on top of the unit and vibration is applied
– When connecting a cable etc. to the rear of the unit
≥ Reactive distance of the sensor is automatically set in accordance with 
the installation conditions at the time of power supply connection and 
when the open/close button is pressed. To prevent an incorrect setting, 
do not place your hands or objects above the unit at these times.
≥ Depending on the usage conditions, the TOUCH-FREE SENSOR may 
stop working or the reactive distance may become shorter. In such 
cases, press the tray open/close button once. 
Install this unit so that the power cord can be unplugged from the 
socket outlet immediately if any problem occurs.
LAN
10BASE-T/100BA
COMMUNICATION
CAMERA
AC power supply cord 
(supplied)
To a household AC outlet
Easy Setting
VQT3B58~Body_eng.fm  12 ページ  ２０１０年１２月１０日　金曜日　午後９時１分 
						

							Connections & Settings
13VQT3B58
The configuration of your network is about to begin. If you 
failed to make the settings, refer to page 14.
Select “Wired” and press [OK].
Follow the on-screen instructions to make your connection 
settings.
Preparation≥Obtain your network name ( >15, SSID).
≥ If your wireless connection is encrypted please be 
sure that you know your encryption key.
≥ [BDT110]  : If “Wireless LAN Adaptor is not connected.” is 
displayed, check that the Wireless LAN Adaptor is fully 
inserted. Alternatively, disconnect and reconnect it. If there 
is still no change in the display, consult your dealer for 
advice.
1Select “Wireless” and press [OK].
2Select “Search for wireless network” or 
“WPS (PUSH button method)” and press 
[OK] then follow the on-screen 
instructions and make the settings.
∫ “WPS (PUSH button method)”
If you are using a Wireless router that supports WPS (Wi-Fi 
Protected Setup), you can easily perform the settings.
∫“Search for wireless network”
The available wireless networks will be displayed.
1 Select your network name and press [OK].
≥If your network name is not displayed search again by 
pressing the [R] button on the remote control. Stealth 
SSID will not be displayed, in this case enter manually.
When your wireless network is encrypted
2 Press [OK] to select “Encryption Key”.
3 Enter your encryption key.
To enter SSID manually
If your SSID is not displayed in step  1, follow these steps.
1 To display SSID input screen : Press [HOME]  > select “Setup”  > select “Player 
Settings”  > select “Network”  > [OK]  > select “Network 
Settings”  > [OK]  > select “Wireless Settings”  > [OK]  > 
select “Connection Setting” > [OK]  > select “Manual 
setting”  > [OK]
2 Press [OK] to select “SSID” and enter your SSID.
≥ If your wireless network is encrypted, go to step  2.Network Easy Setting
Wired connection
Wireless connection
OKRETURN
Network Easy Setting
Wired
Wireless
Select a connection mode. 
 Current setting  :  Wired
 
LAN cable connection:
 Connect a LAN cable to the unit and select Wired.
Wireless LAN connection:
 Select Wireless.
[BDT210]
Wireless Settings
Select a connection method.
Please refer to the operating instructions of your wireless 
access point about connection methods.
Search for wireless network
WPS (PUSH button method)
OKRETURN Search again
SUB
MENU
Wireless Settings
Reception
Select a wireless network for connection.
Network name (SSID)XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
RG BY
Wireless SettingsEnter the encryption key of the wireless network.
Encryption Key
Set
_Encryption Key
Space
12345678901234567890
ABC
DEF
abc
def
ghi
jkl /=
%
+-*
#$&
@
mno []_
pqrs ()
tuv {}
 Iwxyz
“’:;`^
.,?!
JKL
MNO PQRS
TUV
WXY Z
0  -  9    
GH I
~
FinishDelete
OKRETURN
Wireless SettingsEnter your network name (SSID) to connect.
SSIDSet
VQT3B58~Body_eng.fm  13 ページ  ２０１０年１２月１０日　金曜日　午後９時１分 
						

							14VQT3B58
Wireless SettingsNetwork Easy Setting 
(Home Network Connection Check)
Network Easy Setting (Internet Connection Check)
When you experience 
problems with settings
DisplayCheck the following
A conflict with another 
device occurred. ≥
Please wait a few moments, 
and then try again.
A time out error 
occurred. ≥
Setting of the Wireless router 
for MAC Address etc.
≥ The signal may be weak.
[BDT110]  : Using the USB 
extension cable supplied with 
the Wireless LAN Adaptor, 
adjust the position of the 
Wireless LAN Adaptor.
≥ The SSID ( >15) and the 
encryption key of the Wireless 
router.
≥ Please wait a few moments, 
and then try again.
An authentication error 
or a time out error 
occurred.
A device error occurred.
≥
[BDT110]  : Connection of 
Wireless LAN Adaptor
≥ Contact our Customer 
Service Center or  your 
nearest dealer.
OK
Wireless Settings
Failed to complete.
A conflict with another device occurred.
Do you want to configure wireless network connection
setting again ?
Yes NoDisplayCheck the 
following
1. LAN cable connection or  
Wireless setting :Fail≥
Connection of 
the LAN 
cables ( >10)
2. IP address setting : Fail
3. Connection to gateway : Fail
1. LAN cable connection or  
Wireless setting :Pass≥
Connection 
and settings 
of the hub 
and router
≥ Settings of 
“IP Address/
DNS 
Settings” 
(> 32)
2. IP address setting : Fail
3. Connection to gateway : Fail
1. LAN cable connection or
 
Wireless setting :Pass
2. IP address setting :Pass or 
Home 
network 
available
3. Connection to gateway : Fail
DisplayCheck the following
Cannot find the 
server.
(Error code: B019) ≥
“Primary DNS” and “Secondary 
DNS” settings of “IP Address/
DNS Settings” ( >32)
Failed to connect to 
the server.
(Error code: B020) ≥
The server may be busy or the 
service may have been 
suspended. Please wait a few 
moments, and then try again.
≥ Settings of “Proxy Server 
Settings” ( >32) and the router
OK
Network Easy Setting (Home Network Connection Check)
YesNo
Complete.
1. LAN cable connection         
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
: Fail
: Fail
: Fail
OK
Network Easy Setting (Internet Connection Check)Complete.
- Connection to the Internet       :   Fail(Error code: B019)
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the owners manual for the cause of
the error and the solution for it.
Press [OK].
VQT3B58~Body_eng.fm  14 ページ  ２０１０年１２月１０日　金曜日　午後９時１分 
						

							Connections & Settings
15VQT3B58
	≥Refer to the operating instructions of the hub or router.
≥ WPS (Wi-Fi Protected Setup) is a standard that facilitates settings 
relating to the connection and security of wireless LAN devices. To see 
whether your Wireless router supports WPS, check the Wireless router 
operating instructions.
≥ You can perform this setup anytime by selecting “Network Easy Setting” 
in the Setup menu. ( >32)
≥ You can redo these settings individually using “Network Settings”. 
(> 32)
≥ Do not use this unit or Wireless LAN adaptor  to connect to any wireless 
network for which you do not have usage rights.
During automatic searches in a wireless network environment, 
wireless networks (SSID*) for which you do not have usage rights 
may be displayed; however, using these networks may be regarded 
as illegal access.
≥ After performing network settings on this unit, the settings (encryption 
level, etc.) of the Wireless router might change. When you have trouble 
getting online on your PC, perform the network settings on your PC in 
accordance with the settings of Wireless router.
≥ Please be aware that connecting to a network without encryption may 
result in the content of the communication being illegitimately viewed by 
a third party, or the leaking of data such as personal or secret 
information.
* An SSID (Service Set IDentification) is a name used by wireless LAN 
to identify a particular network. Transmission is possible if the SSID 
matches for both devices.
If you have more than one Panasonic player/recorder and 
the remote control operates both products at once, you will
need to change the remote control code on one product to 
prevent this occurrence. ( >33, “Remote Control Code”) Occasionally, Panasonic may release updated firmware for 
this unit that may add or improve the way a feature 
operates. These updates are available free of charge.
This unit is capable of checking the firmware automatically 
when connected to the Internet via a broadband connection.
When a new firmware version is available, the following 
message is displayed.
To update the firmware
Press [HOME] 
> select “Setup” >  select “Player 
Settings”  > select “Others” >  [OK] > select “Firmware 
Update”  > [OK]  > select “Update Now”
DO NOT DISCONNECT the unit from the AC power or 
perform any operation while the update takes place.
After the firmware is installed, “FINISH” will be displayed on 
the unit’s display. Unit will restart and the following screen 
will be displayed.
	≥ If downloading on this unit fails or this unit is not connected to the 
Internet, then you can download the latest firmware from the 
following website and burn it to a CD-R to update the firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
To show the firmware version on this unit. ( >33, “System 
Information”)
≥ Downloading will require several minutes. It may take longer or 
may not work properly depending on the connection environment.
≥ If you do not want to check for the latest firmware version, set 
“Automatic Update Check” to “Off”. ( >33)
Reprogramming the remote 
control
Firmware updates
New firmware is available.
Please update firmware in Setup.
The firmware was updated.Current Version: x.xx
RETURNOK
VQT3B58~Body_eng.fm  15 ページ  ２０１０年１２月９日　木曜日　午後６時３８分 
						

							16VQT3B58
Playback
Inserting or removing 
media
≥When inserting a media item, ensure that it is facing the 
right way up.
≥ When removing the SD card, press on the center of the 
card and pull it straight out.
≥ If you connect a Panasonic product with a USB 
connection cable, the setup screen may be displayed on 
the connected equipment. For details, refer to the 
instructions for the connected equipment.
HOME menu
Major functions of this unit can be operated from the HOME 
menu.
Preparation
Turn on the television and select the appropriate video input 
on the television.
1Press [ ÍPOWER] to turn on the unit.
2Press [OK] or [ 3,4,2 ,1 ] to select the 
item.
≥ When a media is inserted, contents selection screen 
for that media is displayed.
≥ If there are any other items, repeat this step.
≥ To return to HOME menu, select “HOME” or press 
[RETURN] several times.
To show the HOME
 menu
Press [HOME].
	≥ Items to be displayed may vary with the media.
SD CARDCALL
[BDT210]
Vi deo s/
Photos/
Music Disc
Play back the contents. 
(>
17, 21, 22)
≥ When multiple contents are 
recorded, select the types 
of contents or the title.
SD card
USB
Network
Internet 
Content
Displays the Home screen of 
VIERA CAST. (
>23)
Home 
Network
DLNA Client  (>24)
Media Renderer (> 25)
SetupPlayer 
Settings
(>
29)
SD Card 
Management
(> 19)
Wal lpa pe r
Changes the screen 
background of HOME menu.
1
Music
Photos
Videos
Network
Blu-ray Disc Player
HOME
Setup
VQT3B58~Body_eng.fm  16 ページ  ２０１０年１２月７日　火曜日　午前９時４０分 
						

							Playback
17VQT3B58
Playing video contents
1Insert the media.
If the menu is displayed, press [3,4,2,1] to select 
the item. ( >16)
2Press [ 3,4] to select the title and press 
[OK].
When a message screen is displayed while playing back 
3D compatible video software, play back in accordance 
with the instructions.
∫ To show menus
You can show Top Menu, Direct Navigator or Pop-up Menu.
Press [POP-UP MENU/TOP MENU].
≥Press [ 3,4,2,1 ] to select the item and press [OK].
∫ To show the status messages
While playing, press [STATUS].
The status messages give you information about what is 
currently being played. Each time you press [STATUS], the 
display information may change or will disappear from the 
screen.
	≥DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED. 
Press [ ∫STOP] when you have finished playback to protect the unit’s 
motor, your television screen and so on.
≥ Depending on media and contents, the display may change or may not 
appear.
≥ DivX 
[BDT210_for_Canada] and MKV: Successive play is not possible.
≥ It is not possible to playback AVCHD and MPEG2 video which have 　
been dragged and dropped, copied and pasted to the media.
≥ To save on electricity, the power is turned off automatically if there is no 
button operation for about 30 minutes  when not playing back (such as 
when paused, displaying the menu, displaying still pictures, etc.). 
(Compatible with ENERGY STAR)
These functions may not work depending on the media and 
contents.
Press [ ∫STOP].
The stopped position is memorized.
Resume play function
Press [ 1PLAY] to restart from this position.
≥The position is cleared if the tray is opened or you press 
[
∫STOP] several times to display “STOP” on the unit’s display.≥On BD-Video discs including BD-J, the resume play 
function does not work.
Press [ ;PAUSE].
≥Press [ ;PAUSE] again or [ 1PLAY] to restart play.
Search
While playing, press [SEARCH 6] or 
[SEARCH 5].
≥Music and MP3: The speed is fixed to a single step.
Slow-motion
While paused, press [SEARCH 6] or 
[SEARCH 5].
≥BD-Video and AVCHD: Forward direction [SEARCH 5] 
only.
The speed increases up to 5 steps.
≥ Press [ 1PLAY] to revert to normal playback speed.
While playing or paused, press [: ] or 
[ 9 ].
Skip to the title, chapter or track you want to play.
≥Each press increases the number of skips.
While paused, press [ 2] (2;) or [ 1] (;1).
≥Press and hold to change in succession forward or 
backward.
≥ Press [ 1PLAY] to revert to normal playback speed.
≥ BD-Video and AVCHD: Forward direction [ 1] (;1 ) only.
Press [AUDIO].
You can change the audio channel number or soundtrack 
language, etc.
BDDVDCDSDUSB
PlayBD-Video T1     C1     0:05.140:20.52
e.g.BD-Video
Total time
Elapsed time in the title
Current position
T: Title, C: Chapter, PL: Playlist
Other operations during play
St o p
Pause
Search/Slow-motion
Skip
Frame-by-frame
Changing audio
DMP-BDT110_115_210_VQT3B58_eng.book  17 ページ  ２０１０年１２月２日　木曜日　午前９時１８分 
						

							18VQT3B58
1Press [SUB MENU].
2Select an item, then press [OK].
While Direct Navigator screen is displayed
While playing
≥Depending on the played contents if you perform “Screen 
Aspect”, there may be no effect.
≥ When “TV Aspect” ( >31) is set to “4:3 Pan & Scan” or 
“4:3 Letterbox”, the “Zoom” effect in “Screen Aspect” is 
disabled.
	≥ Depending on the media and contents, displayed items are different.
∫ Displaying subtitle text
You can display subtitle text on the DivX  [BDT210_for_Canada] 
and MKV video disc with this unit. The operation might be 
different or it may not operate properly depending on the 
way the file was made or the state of this unit (playing, 
stopped, etc.).
Set “Subtitle” in “Disc” ( >27)
	≥DivX and MKV  video files that do not display “Text” do not contain 
subtitle text.
≥ If the subtitle text is not displayed correctly, try changing the language 
settings. ( >29)
≥ This function has no relation to the subtitles specified in DivX standard 
specifications and has no clear standard.
ABOUT DIVX VIDEO:DivX® is a digital video format created by DivX, Inc. This is 
an official DivX Certified® device that plays DivX video. Visit 
divx.com for more information and software tools to convert 
your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:This DivX Certified® device must be registered in order to 
play purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX VOD 
section in your device setup menu.
Go to vod.divx.com for more information on how to complete 
your registration.
≥ Video images of the copyright-protected DivX contents 
stored on USB device can be output only through the 
HDMI output terminal.
Display the unit’s registration code.
(> 33, “DivX Registration” in “Others”)
≥ After playing DivX VOD content for the first time, the 
registration code is not displayed.
≥ If you purchase DivX VOD content using a registration 
code different from this unit’s code, you will not be able to 
play this content.
Cancel the unit’s registration.
(> 33, “DivX Registration” in “Others”)
Press [ 2,1] to select “Yes” in “DivX Registration”.
Use the deregistration code to cancel the registration in 
www.divx.com.
Regarding DivX VOD content that can only 
be played a set number of times
Some DivX VOD contents can only be played a set number 
of times. When you play this content, the number of times 
already played and initially playable number of times is 
displayed.
≥ The remaining number of plays decreases each time a 
program is played. However, when playing from the point 
where play was previously stopped, the remaining number 
of plays does not decrease due to the resume play 
function.
Useful functions
Properties To display the titles properties (recording 
date, etc.).
View 
ChaptersTo select the chapter.
View 
PlaylistsTo play playlists.
View Titles
To select the title.
Select 
FolderTo switch to another folder.
Screen 
Aspect
When black bars are shown at the top, 
bottom, left, and right sides of the screen, 
you can enlarge the image to fill the 
screen.
To p  M e n uTo display Top Menu.
Pop-up 
MenuTo display Pop-up Menu.
MenuTo display Menu.
3D Settings
2D video can be virtually output as 3D, or 
output effect of the 3D video can be setup. 
(>
20)
Regarding DivX [BDT210_for_Canada]
DivX Registration
The registration code is necessary to
register this unit to play protected
DivX videos.
Registration Code: XXXXXXXXXX
Please register at www.divx.com/vod/
10 alphanumeric 
characters
DMP-BDT110_115_210_VQT3B58_eng.book  18 ページ  ２０１０年１２月６日　月曜日　午前１０時１６分 
						

							Playback
19VQT3B58
BD-Live allows you to enjoy more functions such as 
subtitles, exclusive images and online games by connecting 
this unit to the Internet. Since most of the BD-Live 
compatible discs are played back using the BD-Live 
function, additional contents are required to be downloaded 
into the external memory (local storage).
≥This unit is using an SD card as a local storage device. 
BD-Live function cannot be used when there is no SD card 
inserted.
1Perform network connection and 
settings. ( >10, 13)
2Insert an SD card with 1 GB or more free 
space.
3Insert the disc.
∫Deleting data/Formatting SD cards
If you no longer need data recorded on the SD card, you can 
delete data with the following operation.
1 Insert an SD card.
2 Press [HOME].
3 Press [OK] to select “Setup”.
4 Press [ 1] to select “SD Card Management”.
5 Press [ 3,4] to select “BD-Video Data Erase” or 
“Format SD Card” and press [OK].
6 Press [ 2,1] to select “Yes” and press [OK].
7 Press [ 2,1] to select “Start” and press [OK]. To turn on/off secondary video and audio
[DISPLAY] > select “Disc” > [
1 ] > select 
“Signal Type” > [OK] > set “Video” and 
“Soundtrack” in “Secondary Video” to “On” 
or “Off”
	≥ The usable functions and the operating method may vary with each 
disc, please refer to the instructions on the disc and/or visit their 
website.
≥ Some BD-Live content available on the Blu-ray discs may require an 
Internet account to be created in order to access the BD-Live content. 
Follow the screen display or instruction manual of the disc for 
information on acquiring an account.
≥ To use BD-Live function, it is recommended that you format the card on 
this unit. If the SD card you use is formatted, all data on the card will be 
erased. It cannot be recovered.
≥ “BD-Live Internet Access” may need to be changed for certain discs 
(> 29).
≥ When discs supporting BD-Live are played back, the player or disc IDs 
may be sent to the content provider via the Internet.
≥ During search/slow-motion or frame-by-frame, only the primary video is 
displayed.
≥ When “BD-Video Secondary Audio” in “Digital Audio Output” is set to 
“Off”, secondary audio will not be played ( >30).
Enjoying BD-Live or 
picture-in-picture in BD-Video
Enjoying BD-Live discs with 
Internet
SD Card Management
No. of Files    6
Free space    300 MB
SD card
Format this SD Card.
BD-Video Data Erase
Format SD Card
OKRETURN
Playing picture-in-picture
Secondary videoPrimary video
DMP-BDT110_115_210_VQT3B58_eng.book  19 ページ  ２０１０年１２月８日　水曜日　午後４時３９分 
						

							20VQT3B58
Enjoying 3D video
You can enjoy powerful 3D videos with realistic sensations 
by connecting this unit with a High Speed HDMI Cable to a 
3D compatible TV.
PreparationConnect 3D compatible TV to an HDMI AV OUT terminal of 
this unit using a High Speed HDMI Cable. (>8, 9)
≥ Perform the necessary preparations for the TV.
Method of playback is the same as normal disc playback. 
(> 17)
≥ Playback following the instructions displayed on the 
screen.
Perform the following settings as necessary.
1While playing
Press [ ].
2Select an item, then press [OK].
It appears also by pressing [SUB MENU] and selecting “3D 
Settings”.
	≥ Depending on the contents, displayed items are different.
≥ Please refrain from viewing 3D images if you do not feel well or are 
experiencing visual fatigue.
In the event that you experience dizziness, nausea, or other discomfort 
while viewing 3D images, discontinue use and rest your eyes.
≥ Depending on the connected TV, the video being played back might 
switch to 2D video due to changes in resolution etc. Check the 3D 
setting on the TV.
≥ 3D images may not output as settings of “HDMI Resolution” and “24p 
Output”. (> 31)
3D settings
3D BD-Video 
PlaybackIt is also possible to play back 3D 
discs in 2D (conventional video). 
(>29)
3D Type
If 3D video cannot be played back in 
3D, change the settings as required 
by the connected TV format. ( >31)
≥ Change the settings for 3D on the 
TV also when “Checker board” or 
“Side by side” is selected.
3D Playback 
PrecautionsHide the 3D viewing warning screen. 
(> 31)
Pop-Out Level
Adjust the pop-up position for the 
Playback menu or message screen 
etc. ( >28)
The image is an illustration.
Useful functions
Signal 
Format
OriginalKeep original picture format.
Side by 
side3D picture format comprising of 
left and right screens. 
2D to 3DConverts 2D pictures to 3D effect.
3D 
Picture 
Mode
NormalPlayback pictures with normal 3D 
effects.
Soft
You can enjoy 3D pictures with a 
feeling of broadness, holding 
back the depth perception.
Manual 
Settings
Set 3D effect manually.
Distance
Set the amount of depth 
perception.
Screen Type
Selects how the screen appears 
during 3D playback (flat or 
round).
Frame Width
Set the amount of feathering at 
the edge of screen.
Frame Color
Set the color of feathering at the 
edge of screen.
VQT3B58~Body_eng.fm  20 ページ  ２０１０年１２月９日　木曜日　午後１２時１０分