Panasonic Dmp Bdt210 Owners Manual

							Settings
31VQT3B58
Status Messages
Choose whether to show status messages automatically.
On-screen Language
Choose the language for menus and on-screen messages.
Screen Saver Function
This is to prevent burn-in on the screen.
≥When this is set to “On”:
If there is no operation for 10 minutes or more, Direct 
Navigator screen switches to HOME menu automatically.
≥ While playing and pausing, etc., this function is not 
available.
≥ As for Music [CD-DA] or MP3, regardless of the setting, if 
there is no operation for a while, Direct Navigator screen 
switches to the other states automatically.
Front Panel Display
Changes the brightness of the unit’s display.
≥If “Auto” is selected the display is dimmed during playback 
and bright not during playback.
License
Information about the software used by this unit is displayed.
3D SettingsPress [OK] to show the following settings:
TV Aspect
Set to match the type of television connected.
When connected to a 4:3 aspect television and playing 16:9 
ratio image:
When connected to a 16:9 widescreen television and 
playing 4:3 ratio image:
HDMI Connection
Press [OK] to show the following settings:
Display
TV / Device Connection
3D TypeSelect the format of the connected TV.
≥ Change the settings for 3D on the TV also when 
“Checker board” or “Side by side” is selected.
3D Playback Precautions
Set to display or hide the 3D viewing warning screen when 
playing back the 3D compatible video software.
4:3 Pan & 
Scan
The sides are cut off so 
the picture fills the screen. 
When playing BD-Video, 
video is output as “4:3 
Letterbox”.
4:3 
LetterboxBlack bands appear at the 
top and bottom of the 
picture.
16:9Video is displayed as a 4:3 ratio image in the 
center of the screen.
16:9 FullVideo is displayed as a horizontally 
stretched 16:9 image.
HDMI ResolutionThe items supported by the connected devices are 
indicated on the screen as “ ¢”. When any item without “ ¢” 
is selected, the images may be distorted.
≥ If “Auto” is selected, automatically selects the output 
resolution best suited to the connected television.
≥ To enjoy high-definition video up-converted to 1080p, 
you need to connect the unit directly to 1080p 
compatible HDTV (High Definition Television). If this unit 
is connected to an HDTV through other equipment, it 
must also be 1080p compatible.
24p OutputWhen this unit is connected to a TV supporting 1080/24p 
output using an HDMI cable, movies and other material 
recorded at 24p are output at 24p.
≥When playing DVD-Video, set to “On” and then set “24p” 
in “Video” ( >28) to “On”.
≥ When BD-Video images other than 24p are played, 
images are output at 60p.
≥ 24p :
A progressive image recorded at a rate of 24 frames per 
second (motion-picture film). Many BD-Video movie 
contents are recorded in 24 frames/second in 
accordance with the film materials
.
HDMI Color ModeThis setting is for selecting color-space conversion of the 
image signal when the unit is connected using an HDMI 
cable.
DMP-BDT110_115_210_VQT3B58_eng.book  31 ページ  ２０１０年１２月２日　木曜日　午前９時１８分 
						

							32VQT3B58
Network Easy Setting (>13)
Network Settings
Perform network-related settings individually.
Press [OK] to show the following settings:
HDMI Audio OutputThis setting selects whether or not to output audio from 
HDMI.
≥Select “Off” when the TV is connected to this unit via an 
HDMI terminal, and this unit is also connected to other 
devices, such as an amplifier/receiver via an OPTICAL 
terminal.
VIERA LinkSet to use “HDAVI Control” function when connected with 
an HDMI cable to a device that supports “HDAVI Control”.
≥Select “Off” when you do not want to use “HDAVI 
Control”.
Deep Color OutputThis setting is for selecting whether to use Deep Color 
output when a television that supports Deep Color is 
connected.
Contents Type FlagDepending on the playback content, the TV will output 
adjusting to the optimal method when a TV that supports 
this function is connected.
Network
LAN Connection ModeSelect connection method.
Wireless SettingsThis allows the Wireless router and connection settings to 
be set and the current connection settings and connection 
state to be checked when a wireless connection is used.
Connection Setting
The Wireless router connection wizard will be displayed.
Double Speed Mode Setting (2.4GHz)
When a 2.4 GHz wireless format is used, this setting 
sets the connection speed.
≥If you connect using the “Double Speed Mode 
(40MHz)”, 2 channels use the same frequency band, 
and there is consequently a greater risk of reception 
interference. This can cause the connection speed to 
drop or the connection to become unstable.
IP Address/DNS SettingsThis is for checking the state of the network connection 
and setting the IP address and DNS-related.
Press [OK] to show the respective setting.
≥ “Connection Speed Setting” is enabled only when “Auto 
Detect Connection Speed” is turned “Off”.
Proxy Server Settings
This is for checking the state of connection with the Proxy 
server and performing settings.
Press [OK] to show the respective setting.
Internet Content Settings (> 23) 
(VIERA CAST)
Press [OK] to show the following settings:
Lock
You can restrict the usage of VIERA CAST.
≥ Follow the on-screen instructions. Enter a 4-digit 
password with the number buttons when the password 
screen is shown.
Audio Auto Gain Control
Volume that is different depending on the contents is 
adjusted automatically to the standard volume while 
using the VIERA CAST.
≥Depending on contents, this function effect will not 
work.
≥ Select “Off” when the audio is warped.
Time Zone
By selecting the time zone, it is possible to set the unit’s 
time to match your location.
≥Some VIERA CAST contents require the time zone to 
be set. Set the time zone if necessary.
DST
Select “On” when using Daylight Saving time.
Network Drive Connection
It is possible to access the shared folder of equipment not 
compatible with DLNA, such as the Windows XP operating 
system, and play back video, still pictures, and music on 
this unit.
For the setting and operation method of connected 
equipment, refer to the following Website. 
http://panasonic.jp/support/global/cs/
(This site is in English only.)
DMP-BDT110_115_210_VQT3B58_eng.book  32 ページ  ２０１０年１２月６日　月曜日　午前１０時１６分 
						

							Settings
33VQT3B58
Remote Control Code
Change the remote control code if other Panasonic products 
react to this remote control.
Quick Start
Speed of startup from power off is increased.
≥Internal control unit will be powered when it is set to “On” 
so compared to when the setting is “Off” the following will 
occur.
– Idle power consumption will increase. (about the power 
consumption  >39)
Easy Setting
You can execute basic settings. (“On-screen Language”, 
“TV Aspect”, “Quick Start”, “Touch Free Sensor”  [BDT210])
Restore Default Settings
This returns all values in the Setup menu and the Playback 
menu, except for “Remote Control Code”, “On-screen 
Language”, “LAN Connection Mode”, “Wireless Settings”, 
“IP Address/DNS Settings”, “Proxy Server Settings”, “Lock”, 
“DVD-Video Ratings” and “BD-Video Ratings” etc. to the 
default settings.
Touch Free Sensor [BDT210]
Press [OK] to show the following settings:
DivX Registration (> 18) [BDT210_for_Canada]
You need this registration code to purchase and play DivX 
Video-on-Demand (VOD) content.
System Information
Display firmware version of this unit and wireless LAN 
module.
Firmware Update ( >15)
Press [OK] to show the following settings:
Remote Device Settings ( >25)
Press [OK] to show the following settings:
Remote Device Operation
Enable to operate by DMC.
≥If “On” is selected, “Quick Start” is fixed to “On”.
Setting Unit Name
Set the name of this unit to be displayed on the 
connected equipment.
Registration Type
AutomaticAllow connection to all the equipment that 
is accessing this unit.
ManualSet the permission of the connection 
individually for the equipment that is 
accessing this unit.
Remote Device List
Registering/deregistering of the displayed equipment 
can be performed when “Manual” in “Registration Type” 
is selected.
MAC Address
Displays the MAC address of this unit.
Others
Sensor ( >5)Tray is opened and closed by waving your hands above 
the top part of this unit.
Sound LevelAdjust the volume of the sensor.
Automatic Update CheckWhen this equipment remains connected to the Internet, it 
will check for the latest firmware version when it is turned 
on and you can update it if necessary.
Update NowYou can update the firmware manually if a firmware 
update is available.
VQT3B58~Body_eng.fm  33 ページ  ２０１０年１２月１０日　金曜日　午後９時４１分 
						

							34VQT3B58
Reference
Troubleshooting guide
Before requesting service, please perform 
the following steps.
The following do not indicate a problem with this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
∫Unit doesn’t respond to remote 
control or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 
3 seconds.
– If still unable to power the unit off, disconnect the power 
cord, wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
1 While the unit is off, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “06 FTO” is displayed on 
the unit’s display.
3 Press [OK] on the remote control or [ 33)
To return all settings to the factory preset.
¾Reset the unit as follows:
1 While the unit is off, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “08 FIN” is displayed on 
the unit’s display.
3 Press and hold [OK] on the remote control or [ 4)
¾The remote control and main unit are using different 
codes. If “SET  ” is displayed on the unit’s display when 
a button is pressed on the remote control, change the 
code on the remote control. ( >33)
The TV tuner mode is not displayed when 
the TV is switched on.
¾This phenomenon may occur, depending on the TV 
setting, when “Quick Start” is set to “On”.
– Depending on the TV, this phenomenon may be prevented  by reconnecting the HDMI cable to a different HDMI input 
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “03 VL” is displayed on 
the unit’s display.
3 Press [OK] on the remote control or [  15)
4
Make the following checks and visit our 
website for more information.
For USA : 
www.panasonic.com/help
Enter the model number.
For Canada  : 
http://www.panasonic.ca
4
Or visit our website to find a service 
center.
You can find a service center near you easily on our 
website.
Other support information :
“Customer Services Directory (United States and Puerto 
Rico)” ( >41) or “Limited Warranty (Only for 
CANADA)” ( >42).
General operation
DMP-BDT110_115_210_VQT3B58_eng.book  34 ページ  ２０１０年１２月２日　木曜日　午前９時１８分 
						

							Reference
35VQT3B58
This unit does not recognize the USB 
connection correctly.
¾If USB device is connected to this unit while playing a 
disc or in a video communication the connection will not 
be recognized. Press [HOME] and reconnect USB 
device.
¾[BDT210] : USB memory and USB HDD are not  
recognized via the rear USB port of this unit.
¾Disconnect and reconnect the USB cable. If it still does 
not recognize the connection, turn the power of this unit 
off and on again.
¾USB devices connected using a USB extension cable 
other than the supplied with the Wireless LAN Adaptor 
DY-WL10 (optional)  [BDT110] or a USB hub may not be 
recognized by this unit.
¾If you connect USB HDD to this unit, use USB extension 
cable that is supplied with the HDD.
¾If two USB memory and USB HDD are connected 
simultaneously, they will not be recognized by this unit.
The images from this unit do not appear on 
the television.
Picture is distorted.
¾An incorrect resolution is selected in “HDMI Resolution”. 
Reset the setting as follows:
1 While the unit is on, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “04 PRG” is displayed on 
the unit’s display.
3 Press and hold [OK] on the remote control or [ 31)
– When Dolby Digital Plus, Dolby TrueHD, and DTS-HD  audio are not output in bitstream, select “Yes” in “Restore 
Default Settings” and make proper settings. ( >33)
¾When “3D BD-Video Playback” in the Setup menu is set 
to “Automatic”, images may not be output depending on 
the connection method. After removing the disc from this 
unit, select “Set before play” in the Setup menu, and 
select “2D Playback” in the setup screen displayed 
when playing 3D discs. ( >29)
Video is not output. [BDT210]
¾Set “High Clarity Sound” in the Playback menu to “Off” 
to use the VIDEO OUT terminal. ( >28)
Video is not output in high-definition.
¾Confirm that “HDMI Resolution” in the Setup menu is set 
properly. ( >31)
3D video is not output.
¾Is there a non-3D compatible amplifier/receiver 
connected between this unit and a TV? ( >9)
¾Are the settings on this unit and the TV correct? ( >20)
¾Is the amplifier/receiver that is connected between this 
unit and TV on?
3D video is not output correctly as 2D.
¾Select “Set before play” in the Setup menu, and select 
“2D Playback” in the setup screen displayed when 
playing 3D discs. ( >29)
¾Discs that have recorded titles with Side by side 
(2 screen structure) and that can be enjoyed in 3D are 
played back in accordance with the settings of the TV.
No subtitles.
¾When progressive output is on, closed captions/subtitles 
cannot be displayed.
The subtitles overlap closed captions 
recorded on discs.
¾Turn off the subtitles or turn off the closed caption 
setting on the TV.  (> 27)
A black band is displayed around the edge 
of the screen.
The aspect ratio of the screen is abnormal.
¾Confirm the “TV Aspect” is set properly. ( >31)
¾Adjust the aspect setting on the television.
Cannot switch audio.
¾When connecting an amplifier/receiver using an 
OPTICAL terminal or an HDMI terminal, you cannot 
switch the audio if “Digital Audio Output” is set to 
“Bitstream”. Set “Digital Audio Output” to “PCM”. ( >30)
Cannot hear the desired audio type.
¾Check the connections and the “Digital Audio Output” 
settings. ( >9, 30)
¾To output audio from a device connected with an HDMI 
cable, set “HDMI Audio Output” to “On” in the Setup 
menu. ( >32)
Picture
Audio
DMP-BDT110_115_210_VQT3B58_eng.book  35 ページ  ２０１０年１２月８日　水曜日　午後４時３９分 
						

							36VQT3B58
Disc cannot be played.
¾The disc is dirty. (>4)
Still pictures (JPEG) do not play back 
normally.
¾The images that were edited on the PC, such as 
Progressive JPEG, etc., may not play back.
I can’t play back BD-Live.
¾The SD card is write-protected. ( >7)¾Confirm that this unit is connected to the broadband 
Internet. ( >10)
¾Confirm the “BD-Live Internet Access” settings. ( >29)¾Confirm an SD Card is inserted into the SD Card slot. 
(> 16)
I can’t connect to the network.
¾Confirm the network connection and settings. 
(>10, 13, 32)
¾Check the operating instructions for each device and 
connect accordingly.
When using Wireless LAN connection, video 
from the DLNA Certified media server is not 
played back or video frames are dropped 
during playback.
¾Higher transfer rate router such as 802.11n (2.4 GHz or 
5 GHz) Wireless router may solve the problem. If you 
use 802.11n (2.4 GHz or 5 GHz) Wireless router, it is 
necessary to set the encryption type to “AES”.
Simultaneous use with a microwave, cordless telephone 
etc. at 2.4 GHz may result in connection interruptions or 
other problems.
¾On the “Wireless Settings” screen ( >32), the 
continuous lighting of at least 4 “Reception” indicators is 
the target for a stable connection. If 3 or fewer indicators 
are lit or the connection is being interrupted, change the 
position or angle of your Wireless router and see if the 
connection state improves. If there is no improvement, 
connect to a wired network and perform the “Network 
Easy Setting” ( >13) again.
PlaybackNetwork
DMP-BDT110_115_210_VQT3B58_eng.book  36 ページ  ２０１０年１２月２日　木曜日　午前９時１８分 
						

							Reference
37VQT3B58
Messages
The following messages or service numbers appear on the 
television or unit’s display when something unusual is 
detected during startup and use.
Cannot play.¾You inserted an incompatible disc (Discs recorded in 
PAL video, etc.).
Cannot display on this unit.¾You tried to play a non-compatible image.
¾Confirm “SD” on the unit’s display is not displayed and 
re-insert the card.
No disc is inserted.¾The disc may be upside down.
$ This operation is not available.¾Some operations are unsupported by the unit. For 
example;
– BD-Video: During playback, reverse slow-motion or reverse frame-by-frame is not possible.
IP address is not set.¾The “IP Address” in “IP Address/DNS Settings” is “---. 
---. ---. ---”. Set the “IP Address”, “Subnet Mask”, and 
“Default Gateway”. (Select the automatic address 
acquisition if necessary.)
The current settings only offer minimal 
wireless access point security and low 
performance. It is recommended to change it 
for better security.
¾Authentication type for the Wireless LAN is set to “Open 
system”, or the encryption type is set to “No encryption”. 
It is recommended to encrypt for safety reasons. For 
details, refer to the instructions of the Wireless router 
being used. Encryption is required when playing back 
video, etc., from DLNA compatible devices.
F99¾The unit fails to operate properly. Press [POWER  Í/I] 
on the main unit for 3 seconds to switch the unit to 
standby, then switch back on.
HDMI ONLY¾Some BD-Video discs can only be output with HDMI.
NET¾While connecting to a network.
No PLAY¾There is a viewing restriction on a BD-Video or 
DVD-Video. ( >29)
No READ¾The media is dirty or badly scratched. The unit cannot 
play.
PLEASE WAIT¾The unit is carrying out an internal process. This is not a 
malfunction. You cannot operate the unit while “PLEASE 
WAIT” is displayed.
REMOVE¾The USB device is drawing too much power. Remove 
the USB device.
SET  (“   ” stands for a number.)¾The remote control and main unit are using different 
codes. Change the code on the remote control.
Press and hold [OK] and the 
indicated number button at the 
same time for more than 
5 seconds.
U59¾The unit is hot.
The unit switches to standby for safety reasons. Wait for 
about 30 minutes until the message disappears.
Select a position with good ventilation when installing 
the unit. Do not block the ventilation hole on the side of 
the unit.
U72
U73
¾The HDMI connection is not working properly.
– Turn the unit and TV off.
– Disconnect the HDMI cable between the player and 
the TV.
H  or F (“   ” stands for a number.)
¾There is something unusual.
¾Check the unit using the troubleshooting guide. If the 
service number does not disappear, do the following.
1 Disconnect the plug from the AC outlet, wait a few 
seconds, then reconnect it.
2 Press [POWER Í/I] to turn the power on.
If the service number does not disappear despite doing the 
above, request service from the dealer. Inform the dealer of 
the service number when requesting service.
START¾The system is being restarted during the firmware 
update. Please do not turn off the unit.
UPD /(“    ” stands for a number.)
¾The firmware is being updated.
Please do not turn off the unit.
FINISH¾The firmware update is complete.
On the television
On the unit’s display
VQT3B58~Body_eng.fm  37 ページ  ２０１０年１２月１０日　金曜日　午後９時３０分 
						

							38VQT3B58
Supplemental information
∫Display languages list
∫ Language code list
DisplayLanguageDi splayLanguageDisplayLanguage
LanguageCodeLanguageCodeLanguageCode
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian ARA  
HIN
PER
IND
MRI
BUL
RUM
GRE
TUR 
JPN
CHI
KOR
MAL
VIE
THA
POL
CES
SLK
HUN
FIN Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Polish
Czech
Slovak
Hungarian
FinnishArabic
Hindi
Persian
Indonesian
Maori
Bulgarian
Romanian
Greek
Turkish
Others
Abkhazian: 6566
Afar: 6565
Afrikaans: 6570
Albanian: 8381
Amharic
:6577
Arabic: 6582
Armenian: 7289
Assamese: 6583
Aymara: 6589
Azerbaijani: 6590
Bashkir: 6665
Basque: 6985
Bengali; Bangla: 6678
Bhutani: 6890
Bihari: 6672
Breton: 6682
Bulgarian: 6671
Burmese: 7789
Byelorussian: 6669
Cambodian: 7577
Catalan: 6765
Chinese: 9072
Corsican: 6779
Croatian: 7282
Czech: 6783
Danish: 6865
Dutch: 7876
English: 6978
Esperanto: 6979
Estonian: 6984
Faroese: 7079
Fiji: 7074
Finnish: 7073
French: 7082
Frisian: 7089
Galician: 7176
Georgian: 7565
German: 6869
Greek: 6976
Greenlandic: 7576
Guarani: 7178 Gujarati: 7185
Hausa: 7265
Hebrew: 7387
Hindi: 7273
Hungarian: 7285
Icelandic: 7383
Indonesian: 7378
Interlingua: 7365
Irish:
7165
Italian: 7384
Japanese: 7465
Javanese: 7487
Kannada: 7578
Kashmiri: 7583
Kazakh: 7575
Kirghiz: 7589
Korean: 7579
Kurdish: 7585
Laotian: 7679
Latin: 7665
Latvian, Lettish: 7686
Lingala: 7678
Lithuanian: 7684
Macedonian: 7775
Malagasy: 7771
Malay: 7783
Malayalam: 7776
Maltese: 7784
Maori: 7773
Marathi: 7782
Moldavian: 7779
Mongolian: 7778
Nauru: 7865
Nepali: 7869
Norwegian: 7879
Oriya: 7982
Pashto, Pushto: 8083
Persian: 7065
Polish: 8076
Portuguese: 8084
Punjabi: 8065
Quechua: 8185 Rhaeto-Romance:
8277
Romanian: 8279
Russian: 8285
Samoan: 8377
Sanskrit: 8365
Scots Gaelic: 7168
Serbian: 8382
Serbo-Croatian: 8372
Shona: 8378
Sindhi: 8368
Singhalese: 8373
Slovak: 8375
Slovenian: 8376
Somali: 8379
Spanish: 6983
Sundanese: 8385
Swahili: 8387
Swedish: 8386
Tagalog: 8476
Tajik: 8471
Tamil: 8465
Tatar: 8484
Telugu: 8469
Thai: 8472
Tibetan: 6679
Tigrinya: 8473
Tonga: 8479
Turkish: 8482
Turkmen: 8475
Twi: 8487
Ukrainian: 8575
Urdu: 8582
Uzbek: 8590
Vietnamese: 8673
Volapük: 8679
Welsh: 6789
Wolof: 8779
Xhosa: 8872
Yiddish: 7473
Yo r u b a : 8 9 7 9
Zulu: 9085
DMP-BDT110_115_210_VQT3B58_eng.book  38 ページ  ２０１０年１２月２日　木曜日　午前９時１８分 
						

							Reference
39VQT3B58
Specifications
Signal system: NTSC
Operating temperature range:
i5 oC to  i35  oC ( i41  oF to  i95  oF)
Operating humidity range: 10 % to 80 % RH (no condensation)
Video output: 1.0 Vp-p (75≠)/Pinjack:1system
Audio output: 2 Vrms (1 kHz, 0 dB)/Pin jack
Number of connectors : 2 channel:1 system
Digital audio output:
Optical digital output (Optical terminal)
HDMI AV output: Type A (19 pin) : 1 system
This unit supports “HDAVI Control 5” function.
SD card slot:  Connector : 1 system
USB slot: USB2.0 : 2system
Ethernet:  10BASE-T/100BASE-TX : 1 system
WLAN  [BDT210]
Antenna: Tx 1, Rx 2
Standard Compliance: IEEE802.11n / IEEE802.11a / IEEE802.11g / 
IEEE802.11b
Transmission system: MISO-OFDM system, OFDM system, DSSS 
system
Transfer rate (standard)*:
IEEE802.11n:  Tx Max. 150 Mbps, Rx Max. 
300 Mbps
IEEE802.11g / IEEE802.11a:  Max. 54 Mbps
IEEE802.11b: Max.  11 Mbps
Access Mode: Infrastructure mode
Security: WPA2-PSK (TKIP/AES)
WPA-PSK (TKIP/AES)
WEP (64 bit / 128 bit)
(
This unit supports WPA and WPA2 encryption.)LASER Specification
Class  I LASER Product:
Wave length:
790 nm (CDs)/655 nm (DVDs)/405 nm (BDs)Laser power: No hazardous radiation is emitted with the  safety protection
Power supply: AC 120 V, 60 Hz
Power consumption:  Approx. 9.9 W
Power consumption in standby mode:
Approx. 0.1 WPower consumption in quick start standby mode:Approx. 3.2 WDimensions (Wk Dk H)  Including the projecting parts:
430 mmk185 mm k35 mm
(Approx. 16 15/16 zk7 5/16 zk1 7/16z)
Mass (Weight): Approx. 1.6 kg (3.52 lbs)
Specifications are subject to change without notice.* Transfer rates are theoretical values; however, actual communication 
rate will vary according to communication environment or connected 
equipment.
≥With certain recording states and folder structures, the 
play order may differ or playback may not be possible.
The audio output differs depending on which terminals are 
connected to the amplifier/receiver, and the settings on the 
unit. ( >30, Digital Audio Output)
≥ The number of channels listed is the maximum possible 
number of output channels  when connected to amplifier/
receiver compatible with the respective audio format.
*1When “BD-Video Secondary Audio” is set to “On”, the audio will be 
output as Dolby Digital, DTS Digital Surround or 5.1ch PCM.
*2[BDT110] : The maximum possible number of Dolby sound is 5.1ch 
PCM.
*3The audio output is amplified from 5.1ch or 6.1ch to 7.1ch depending on 
the DTS, Inc. specifications.
File format
File formatExtensionReference
MP3 “.MP3”, “.mp3” ID3 tags (Only titles and 
the names of artists)
JPEG
“.JPG”, “.jpg” ≥
MOTION JPEG and 
Progressive JPEG is not 
supported
≥ You may not be able to 
play back the file if you 
have edited the folder 
structure or the file 
name on a PC or other 
device.
DivX 
[BDT210_for_Canada]
“.DIVX”, “.divx”, 
“.AVI”, “.avi” ≥
The video file and 
subtitles text file are 
inside the same folder, 
and the file names are 
the same except for the 
file extensions.
≥ Some DivX and MKV 
file may not be played 
back, depending on the 
video resolution and 
frame rate condition.
Subtitles text 
file
“.SRT”, “.srt”, 
“.SUB”, “.sub”, 
“.TXT”, “.txt”
MKV
“.MKV”, “.mkv”
Subtitles text 
file
“.SRT”, “.srt”, 
“.SSA”, “.ssa”, 
“.ASS”, “.ass”
Audio information
Te r m i n a l“Digital Audio Output”
“Bitstream”“PCM”
HDMI AV 
OUT Outputs using original 
audio*1
BD-Video : 
7.1ch PCM*1*2 *3
DVD-Video : 
5.1ch PCM
OPTICAL
Dolby Digital/
DTS Digital Surround Down-mixed 2ch 
PCM
VQT3B58~Body_eng.fm  39 ページ  ２０１０年１２月１０日　金曜日　午後１時２９分 
						

							40VQT3B58
Java and all Java-based trademarks and logos are trademarks or 
registered trademarks of Sun Microsystems, Inc. in the United States 
and other countries.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195; 
7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents 
issued & pending. 
DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD 
Master Audio | Essential and the DTS logos are trademarks of DTS, Inc. 
Product includes software. 
© DTS, Inc. All Rights Reserved.
This item incorporates copy protection technology that is protected by 
U.S. patents and other intellectual property rights of Rovi Corporation.\
 
Reverse engineering and disassembly are prohibited.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are 
trademarks or registered trademarks of HDMI
Licensing LLC in the 
United States and other countries.
This product is licensed under the AVC patent portfolio license and 
VC-1 patent portfolio license for the personal and non-commercial use 
of a consumer to (i) encode video in compliance with the AVC Standard \
and VC-1 Standard (“AVC/VC-1 Video”) and/or (ii) decode AVC/VC\
-1 
Video that was encoded by a consumer engaged in a personal and 
non-commercial activity and/or was obtained from a video provider 
licensed to provide AVC/VC-1 Video. No license is granted or shall be 
implied for any other use. Additional information may be obtained from 
MPEG LA, LLC.
See http://www.mpegla.com.
HDAVI Control™ is a trademark of Panasonic Corporation.
VIERA Link™ is a trademark of Panasonic Corporation.
VIERA CAST™ is a trademark of Panasonic Corporation.
EZ Sync™ is a trademark of Panasonic Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS 
and Thomson.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic 
Corporation and Sony Corporation.
SDXC Logo is a trademark of SD-3C, LLC.
“DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation\
.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
DivX®, DivX Certified® and associated logos are trademarks of DivX, 
Inc. and are used under license.
DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service 
marks, or certification marks of the Digital Living Network Alliance.
gSOAP Public License 1.3
Part of the software embedded in this product is gSOAP software.
Portions created by gSOAP are Copyright (C) 2001-2009 Robert A. van 
Engelen, Genivia inc. All Rights Reserved.
THE SOFTWARE IN THIS PRODUCT WAS IN PART PROVIDED BY 
GENIVIA INC AND ANY EXPRESS OR IMPLIED WARRANTIES, 
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE 
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, 
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED 
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 
POSSIBILITY OF SUCH DAMAGE.
Windows is a trademark or a registered trademark of Microsoft 
Corporation in the United States and other countries.
YouTube and Picasa are trademarks of Google, Inc.
Skype, associated trade marks and logos and the “      ” logo are \
trade 
marks of Skype Limited.
This product incorporates the following software:
For the software categorized as (3) and (4), please refer to the ter\
ms 
and conditions of GPL v2 and LGPL v2.1, as the case may be at 
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and 
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html.
In addition, the software categorized as (3) and (4) are copyrighted\
 by 
several individuals. Please refer to the copyright notice of those 
individuals at 
http://www.am-linux.jp/dl/AWBPP11
The GPL/LGPL software is distributed in the hope that it will be useful,\
 
but WITHOUT ANY WARRANTY, without even the implied warranty of 
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. 
At least three (3) years from delivery of products, Panasonic will giv\
e to 
any third party who contacts us at the contact information provided 
below, for a charge no more than our cost of physically performing 
source code distribution, a complete machine-readable copy of the 
corresponding source code covered under GPL v2/LGPL v2.1.
Contact Information
[email protected]
Source code is also freely available to you and any other member of 
the public via our website below.
http://www.am-linux.jp/dl/AWBPP11 the software developed independently by or for Panasonic 
Corporation,
the software owned by third party and licensed to Panasonic 
Corporation,
the software licensed under the GNU General Public License, 
Version 2 (GPL v2),
the software licensed under the GNU LESSER General Public 
License, Version 2.1 (LGPL v2.1) and/or,
open sourced software other than the software licensed under the 
GPL v2 and/or LGPL v2.1
(1)
(2)
(3)
(4)
(5)
This product includes software developed by the OpenSSL Project 
for use in the OpenSSL Toolkit.
 (http://www.openssl.org/)
This product includes software developed by the University of 
California, Berkeley and its contributors.
FreeType code.
The Independent JPEG Groups JPEG software.
For the software categorized as (5) includes as follows.
1.
2.
3.
4.
VQT3B58~Body_eng.fm  40 ページ  ２０１０年１２月１３日　月曜日　午後５時３６分