Panasonic Document Scanner Kv S1057c_s1027c_sl1066_sl1056_sl1055_sl1036_sl1035 Operating Manual

							Check the AccessoriesCheck that all accessories are included before installing the unit. In the event that an item is missing, please
contact your dealer.AccessoriesNameNotes
USB cable—Software /
Manual CD-ROMDrivers, Applications, Utilities, DocumentsMixed batch card guideWhen the unit is shipped, this is stored in the
feed tray.Quick Installation Guide—Power cord
Two power cords may be included. Use the
power cord appropriate for where you use the
unit.
Note
•It is highly recommended to keep the original carton and all packing materials. They are necessary
when repacking.
Operating Manual11
Before You Start      
						

							Main Unit
Front
Document guides
Mixed batch card guide
Manual feed selector
Switches the scanning method between continuous scanning (Auto) and manual scanning (Manual).
Operation panel
For details, refer to "Operation Panel and LED Indicators" (page 14).
Exit tray
Exit extension tray 1
Exit extension tray 2
Exit stopper
Exit guides
Fan exhaust vent
ADF door
ADF door release
Feed tray
Feed extension tray
12Operating ManualL
o
c
a
t
i
o
n
o
f
C
o
n
t
r
o
l
s
Location of Controls1
2
3
5
4
678
9
10
11
12
14
13                
						

							Rear
Security slot
Use a commercially available security cable.
USB connector
USB cable
Connect the USB cable to the scanner and the other end of the USB cable to the computer.
Power cord
AC inlet
Operating Manual13
Location of Controls12
3
45       
						

							Operation Panel and LED IndicatorsnKV-S1057C and KV-S1027C
nKV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035
ALED ( Red)
Lights when an error occurs.BLED ( Green )
Shows the scanner’s status.CPower button
Press the power button for more than one second to turn the unit off.DCursor buttonESkip button
If you press this button after a double feed is detected and scanning has been paused, the document
(or documents) detected as a double feed will be scanned, and then ejected from the scanner.
Scanning will continue after the document is scanned and ejected.14Operating Manual
Location of Controls123456
78 123546
9  
						

							FStart/Stop button
• If you set [Wait Key] for "Manual Feed Mode" in your application software, pushing this button
starts scanning. For details about "Manual Feed Mode", refer to the Image Capture Plus,
TWAIN, or ISIS help.
• During scanning, pushing this button stops scanning.
• If you press this button after a double feed is detected and scanning has been paused, the
document (or documents) detected as a double feed will be ejected from the scanner without
being scanned. Scanning will stop.n  KV-S1057C and KV-S1027C onlyGLCDHOK buttonIf you are using the scanner with Image Capture Plus, you can perform a push scan using the LCD.
Registered jobs are displayed on the LCD. Use the cursor button ( D) to select a job. Also, error
codes and messages corresponding to the scanner status are displayed on the LCD.n  KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035 onlyI7-segment LEDIf you are using the scanner with Image Capture Plus, you can perform a push scan using the
7- segment LED. A registered job number is displayed on the 7 -segment LED. Use the cursor button
( D ) to select a job.Operating Manual15
Location of Controls 
						

							About LEDThe status of the scanner is displayed by the LED (Red) (A) and the LED  (Green) (B), as shown in the
table below:A  LED ( Red)B LED ( Green )StatusOFFOFFPower OFF *1OFFONReady mode or ScanningOFFBlinking (Slow, Long ON)Sleep mode *2Blinking (Slow)ONWarningONOFFError*3OFFBlinking (Fast)Warming upOFFBlinking (Fast, 2 times consecutively)Double Feed Skip mode
*1
If the power off feature in sleep mode is enabled, and if no operation is performed for a certain period of time, the scanner will be
turned off automatically. Press the power button of the scanner to turn it on. You can enable/disable the power off feature, and change
the time until the scanner turns off in User Utility.
*2 If no operation is performed for 15 minutes or longer, the scanner will enter sleep mode automatically to conserve energy. Press any
button (except the power button) on the scanner’s operation panel to return to ready mode. The time until the scanner enters sleep
mode can be changed in User Utility.
*3 For details about the error, refer to "Error Messages (KV-S1057C and KV-S1027C only)" (page 69) or check in User Utility.
16Operating Manual
Location of Controls 
						

							Required Space Around the ScannerIn order to ensure proper operation, install the unit maintaining the proper distances from surrounding objects,
as shown in the following illustration.
Notice
•Do not move the unit immediately from a cold place to a warm place. It may cause condensation, which
may damage the unit.
Operating Manual17I
n
s
t
a
l
l
a
t
i
o
n
Installation272 mm (10.7 in.)
300 mm
(11.8 in.)
500 mm(20 in.) 750 mm(30 in.)238 mm(9.4 in.)
400 mm(16 in.)  
						

							Installing the Software
Notice•Make sure to connect the unit to your computer after installing the software. Connecting the unit to your
computer and turning on the unit’s power before installing the software may influence the software
installation. If you connect the unit to your computer and turn on the unit’s power before installing the
software by mistake, install the software after disconnecting the unit from your computer.
• Make sure to log on as an administrator to install the software.
The software on the enclosed Software / Manual CD-ROM can be installed on your computer.
You can select from the 2 installation methods below, depending on your needs.
a. Complete : Install all the drivers, applications, utilities and Operating Manual.
b. Custom : Install one of the software or Operating Manual.
Note
•Normally, it is recommended to select [Complete].
1. Check that the unit has been turned off.
• If the power is turned on, press and hold the power button for more than one second to turn the unit
off.
2. Insert the Software / Manual CD-ROM into the CD/DVD drive on your computer.
• If you have a feature called "Autorun" activated, the installation process will start automatically.
• The setup window will appear.
Note
•If the AutoPlay dialog box is displayed, select [CDRun.exe].
• If the setup window does not appear, double -click [ CDRun.exe ] in the Software / Manual CD -ROM.
3. Check the [Read me first] file.
4.Select the desired installation methods from "Software" on the left side of the screen.
• If you selected [Complete], continue to step 6.
If you selected [Custom], continue to step 5.
18Operating Manual
Installation   
						

							5.If you selected [Custom] for the installation type in step 4, select the item that you want to install.
Note
•If you select TWAIN or ISIS, Image Capture Plus will also be installed.
6. Follow the instructions on the screen and complete the installation.
• Restart your computer if you are prompted to do so.
Operating Manual19
Installation   
						

							Installing the Unit1.Remove all packing tape and cushioning.
2. Pull out the feed extension tray in the direction of the arrow shown in the illustration below.
3.Set the exit tray.
a. Raise the exit stopper.
20Operating Manual
Installation