Panasonic Door Station Vl Gc001an Installation And Operation Guide

							Thank you for purchasing a Panasonic Door Station.
Please read this Installation and Operation Guide before using the unit and save for future 
reference.
Door Station
Installation and Operation Guide
Model No. VL-GC001A
PFQX2165ZA     DC0405NK0
VL-GC001A.book  Page 1  Monday, February 28, 2005  12:08 PM 
						

							2
Table of Contents
Important Information
Important safety instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
Additional safety information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
For best performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction and Installation
Included items  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
Location of controls  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Before installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
Installing the door station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Help
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
General Information
Technical data about this product  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
FCC and Other Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
VL-GC001A.book  Page 2  Monday, February 28, 2005  12:08 PM 
						

							3
Important Information
Important safety instructions
1) Read these instructions.
All the safety and operating instructions should be read before the appliance is operated.
2) Keep these instructions.
The safety and operating instructions should be retained for future reference.
3) Heed all warnings.
All warnings on the appliance and in the operating instructions should be adhered to.
4) Follow all instructions.
All operating and use instructions should be followed.
5) Do not use this apparatus near water.
For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, 
or near a swimming pool, and the like.
6) Clean only with dry cloth.
Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions. 
Slots and Openings in the cabinet are provided for ventilation and to ensure reliable 
operation of the product and to protect it from overheating. The openings should never be 
blocked by placing the product on a bed, sofa, rug, or other similar surface.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other 
apparatus (including amplifiers) that produce heat. 
This product should not be placed in a built-in installation such as a bookcase or rack 
unless proper ventilation is provided or the manufacturer’s instructions have been 
adhered to.
9) Only use attachments / accessories specified by the manufacturer.
10) Refer all servicing to qualified service personnel. Servicing is required when the 
apparatus has been damaged in any way, such as power- supply cord or plug is damaged, 
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been 
exposed to rain or moisture, does not operate normally, or has been dropped.
SAVE THESE INSTRUCTIONS
The lightning flash with arrow 
head within a triangle is 
intended to tell the user that 
parts inside the product are a 
risk of electric shock to persons.The exclamation point within a 
triangle is intended to tell the 
user that important operating 
and servicing instructions are in 
the papers with the appliance.
CAUTION
RISK OF ELECTRIC SHOCK 
DO NOT OPEN
VL-GC001A.book  Page 3  Monday, February 28, 2005  12:08 PM 
						

							4
Important Information
Additional safety information
1. Use only the power source marked on the unit. If you are not sure of the type of power 
supplied to your home, consult your dealer or local power company.
2. Use only the specified AC adaptor.
3. Do not tamper with the plug.
4. Make sure the plug is securely inserted.
5. Do not touch the plug with wet hands.
6. Do not place objects on the power cord. Install the unit where no one can step or trip on 
the cord.
7. To reduce the risk of electric shock, do not disassemble this unit. Take the unit to an 
authorized service center when service is required. Opening or removing covers may 
expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric 
shock when the unit is subsequently used.
8. Unplug the monitor station from power outlets and refer servicing to an authorized service 
center when the following conditions occur:
A. If smoke rises, or an unaccustomed noise or smell is discharged from the unit.
B. If metal objects have been dropped inside the monitor station.
9. Do not put your ear(s) near the speaker, as loud sounds emitted from the speaker may 
cause hearing impairment.
10. Only a qualified technician is allowed to connect a power cable to the unit. 
Contact an authorized service center.
11. Do not make any wiring connections when the power supply is turned on.
12. Never install wiring during a lightning storm.
13. When existing chime wires are used, it is possible that they contain AC voltage. Electric 
shock or unit damage could result. Contact an authorized service center.
14. Be sure to install the unit as specified to endure the mass.
15. If the wiring is outdoors, use a protection tube or a surge protector.
16. If the wiring is underground, do not make any connections underground.
17. WARNING 
– Unplug the monitor station from power outlets if it emits smoke, an abnormal 
smell or makes unusual noise. These conditions can cause fire or electric shock. Confirm 
that smoke has stopped and contact an authorized service center.
For best performance
LIf a power failure occurs, the unit will not function.
VL-GC001A.book  Page 4  Monday, February 28, 2005  12:08 PM 
						

							5
Introduction and Installation
Included items
1234
5
No.ItemQuantityNotes
1Door station 1 ------
2Mounting bracket 1 Attached to rear of the door station.
3Wood screws 2 For the door station.
(3.8 mm x 20 mm, 
1/8 x13/16)
4Allen wrench 1 ------
5Bolt covers 2 One for spare.
VL-GC001A.book  Page 5  Monday, February 28, 2005  12:08 PM 
						

							6
Introduction and Installation
Location of controls
Front view Rear view
ACamera
LWhen a visitor presses the Call Button, the camera will turn on and an image of the 
visitor will be shown on the display of the monitor station.
BMicrophone
CCall Button
LThe Call Button is lit with a blue LED light while the power is on.
LA visitor can press this button to call the monitor station.
DSpeaker
EWater drain hole
LThis hole allows rain water to drain. Do not cover it.
FCamera angle control lever
LThe camera angle can be adjusted when installing the door station (page 7, 10).
A
B
EF
C
D
VL-GC001A.book  Page 6  Monday, February 28, 2005  12:08 PM 
						

							7
Introduction and Installation
Before installation
To avoid malfunction or communication disturbances, do not install the door station in the 
following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places where a high concentration of dust, hydrogen sulfide, phosphorus, ammonia, sulfur, 
carbon, acid, or noxious fumes occur.
– Within 2 m (67) of a TV, microwave, personal computer, air conditioner or any other 
electrical device.
Standard installation position of the door station and camera range
Upper/lower range
LSide view of when the camera is facing the 
front at 0°.Left/right range
LTop view of when the camera is facing the 
front at 0°.
LTop view of when the camera is facing the 
left at 15°.
LTop view of when the camera is facing the 
right at 15°.
500 mm
(1911/16)
Image range:
425 mm (163/4) Center of the 
door station
1450 mm
(571/16)
46°
Image range:
580 mm (2213/16)
500 mm
(1911/16)60°
L
R
Image range:
650 mm (259/16)
L
R
Image range:
650 mm (259/16)
L
R
VL-GC001A.book  Page 7  Monday, February 28, 2005  12:08 PM 
						

							8
Introduction and Installation
Note:
LThe measurements and angles are for reference purposes and may vary depending on the 
environment.
LIf a strong light is shining on the door station, the visitor’s face may not be distinguishable. 
Do not place the door station in the following locations.
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the door station.
– Where echoing occurs, causing the unit to beep frequently.
LMake sure the back of the door station is not subject to water.
Wire type and distance
LWire (between the monitor station and the door station):
Type: General cable CAT-3 24 AWG
Distance: Maximum 100 m (about 328 feet)
VL-GC001A.book  Page 8  Monday, February 28, 2005  12:08 PM 
						

							9
Introduction and Installation
Installing the door station
Make sure to install the door station on a flat, vertical wall.
Important information: 
On the bottom surface of the door station, there is a hole to allow water to drain. Do not 
cover it up when installing.
1Unscrew the hex-head screw using the longer end of the allen wrench and remove the 
mounting bracket from the rear of the door station.
LThe pin hole camera is not a screw to be touched or removed.
Hex-head screw
(Attached to the door station)
Allen wrenchMounting bracket
Pin hole camera
VL-GC001A.book  Page 9  Monday, February 28, 2005  12:08 PM 
						

							10
Introduction and Installation
2Attach the mounting bracket to the wall using the wood screws (3.8 mm x 20 mm, 1/8 x 13/16).
LBefore drilling, see page 7 for installation location.
3Connect the wires that connect to the monitor station to the terminal connector by 
unscrewing the screws, pushing in the wires, then tightly fastening the screws.
LSee page 8 for the wire type and distance.
LYou can change the camera angle using the camera angle control lever. See page 7 for 
details.
Wood screws
Wall Mounting bracket
83.5 mm
(3
5/16)
Camera angle control lever
Wire (Not included) Terminal connector
(Non polar)
Screw
VL-GC001A.book  Page 10  Monday, February 28, 2005  12:08 PM