Panasonic Dvd Player Receiver Cq Vd7001 Installation Safety Information Manual

							63
CQ-VD7001W
62
CQ-VD7001WInstallation 
(continued)
!1Spacer
!2Double-Faced Adhesive Tape iRound Head Screw 
(5 mmø x 6 mm)Bracket Mounting Hole
of a Bracket
(in section)
Existing Bracket (L) (Bracket originally attached to the car)!2Double-Faced 
Adhesive TapeExisting Bracket (R)iRound Head Screw
(5 mmø x 6 mm)
!1Spacer
❏Installation Procedures (When not using Mounting Collar w)Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car
manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.
Select mounting screws according to the hole positions and hole shape of the bracket.
oFlat-Head Screw (5 mmø x 6 mm) 4 pieces !0Round Head Screw (4 mmø x 3 mm)
4 pieces iRound Head Screw (5 mmø x 6 mm) 2 pieces
Recycle the Round Head Screws that fixed the transportation brackets for two more 
positions.
When using these
mounting holes
qPush the right and left clamp plates outward, one at a time, and pull the unit toward yourself.
wAfter removing the right and left clamp plates, pull the unit with both hands till it comes out.
* To remove Trim Plate q, pull it from right side to left side.
Push here to
remove the
clamp plates. qw
To Remove the Unit
Use the supplied Spacer !1if mounting hole of your
car is shaped like below.
–
+
SIDE  BRAKE
The side brake (parking brake) switch position varies with car model.
For details on the exact location of the side brake (parking brake) switch
in your car, contact your dealer.
qAttach a Clip Connector 
!5
to the end of the side
brake (parking brake) connection lead.
w
The Clip Connector 
!5
is connected to the power
source side lead of the side brake (parking brake)
lever.
Connecting the Side Brake (Parking Brake) Connection LeadHand brake Foot brakeSide Brake (Parking Brake) Connection
Lead(Blue/yellow stripe)
When the side brake (parking brake) lever is
engaged, the unit is grounded by the chassis.
Side brake (parking brake) switch
Car chassis Battery Brake light
!5
Clip Connector
Side Brake (Parking Brake)
Connection Lead
(Blue/yellow stripe)
Comes up to this point.
Power source side lead
Caution
¡For safety, be sure to ask your nearest professional installer to do this connection. 
						

							VIDEO-OUTVTR-IN
PRE-OUT REARREMOTE-OUTS.W-OUT PRE-OUT CENTERTV-CONT
PRE-OUT FRONTCAMERA-INCH/AUX-INREMOTE-IN
65
CQ-VD7001W
Note:¡To prevent from damage to the unit, be sure to follow the wiring diagrams below.¡Be sure to fully plug in the connectors. Secure them with clamps and tapes.¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or
your dealer if other methods are required.
Video Output Terminal (VIDEO-OUT)
Connect the rear monitor. (
a
page 68) Radio Antenna Connector (RADIO ANT IN) DIN Connector
To the DIN connector of a CD changer/DVD Changer. 
(e.g. CX-DP880, CX-DH801W).RGB Connector
To the Panasonic Car Navigation System (available in future).
Remote-Out Lead
To Remote-In of connected device.
Pre-Out Connector (front)
To external amplifier.
Pre-Out Connector (center)
To external amplifier.
Pre-Out Connector (rear)
To external amplifier.
Pre-Out Subwoofer connector (mono)
To external amplifier.
Video Input Terminal (VTR-IN)
Connect a VCR, camcorder, other brand’s car
navigation system, etc. (apage 68)
Remote-In Lead
(not used) Changer/AUX Input Connector
To the RCA cord of a changer/AUX.
Camera Input Terminal (CAMERA-IN)
Connect a rear view camera. (a
page 69)/
DVD Changer (
a
page 67)
TV Control Lead (TV-CONT)
(not used)
(R)(Red)
(L)(White)
(R)(Red)
(L)(White)
(R)(Red)
(L)(White) (Yellow)
(R)(Red)
(L)(White)
(R)(Red)
(L)(White) (Yellow)
(Yellow)
(Blue/red stripe) (Brown/black stripe)(Black)
(Black)
(Black)CQ-VD7001W
(Rear)
This manual refers to the connection to the Panasonic car navigation system that may possibly come on the market in
the future. Descriptions regarding the connection with Panasonic car navigation system are boxed with dotted line. 
64
CQ-VD7001WElectrical Connections
BATTERY 15 AREVERSESIDE BRAKENAVI MUTEANT-CONT MAX 0.1A
FRONT SPREAR SP
AMP-CONT MAX 0.1AACC
Motor Antenna Relay Control Lead (Blue)(To motor antenna) (Max. 100 mA)This lead is not intended for use with a switch actuated
power antenna.
Front Right +(Gray)
Front Right –(Gray/black stripe)
Front Left +(White)
Front Left –(White/black stripe)
Rear Right +(Violet)
Rear Right –(Violet/black stripe)
Rear Left +(Green)
Rear Left –(Green/black stripe) External Amplifier Control Power Lead (Blue/white stripe)
To an external amplifier.
Battery Lead (Yellow)
To the car battery, continuous +12 V DC. Power Lead (Red)
To ACC power, +12 V DC.
Ground Lead (Black)
To a clean, bare metallic part of the car chassis 
Speaker connections• Do not connect more than one speaker to one set of
speaker leads (except for connecting to a tweeter).
• Do not use a 3-wire type speaker system having a com-
mon earth lead.
Navi Mute Lead (Orange)
Connect to the Navi Mute Lead of the Panasonic car
navigation system. (available in future)
Side Brake (Parking Brake) Connection Lead (Blue/yellow
stripe)
Be sure to wire the side brake (parking brake) for safety and
preventing accidents. (apage 63)
Reverse Lead (Violet/white stripe)
When connecting the rear view camera, use the reverse lead.
(apage 69)
Note:
Use a Reverse Extension Cord 
!4
if needed.(Noise Filter) (Fuse 15 A)(Resistor 1 kΩ)
Caution
¡This unit is designed for use in a car having a 12 V negative ground battery system.
¡Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from any
metal parts.
¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may
clear the memory.
¡Run the cords avoiding the spots where the temperature can be extremely high.
!3 
Power Connector 
						

							67
CQ-VD7001W
66
CQ-VD7001WElectrical Connections 
(continued)
CH/AUX-IN
Connection with CD Changer (CX-DP880) 
CQ-VD7001W
(Rear)
DIN Connector
DIN Cord (Black)
CD ChangerCX-DP880
(option)
Power Connector
(Supplied with CX-DP880)
RCA Cord
(L) (White) (R) (Red)Battery Lead (Yellow)
To the car battery, continuous
+12 V DC Ground Lead (Black)
To a clean, bare metallic part of the car
chassis Note:
¡Refer to the operating instructions for the connected devices, in addition.
ACC
VTR-IN
REMOTE-OUT
CH/AUX-IN
CAMERA-IN
REMOTE-OUT
BATTERY 5 AACC
Connection with DVD Changer (CX-DH801W) 
CQ-VD7001W
(Rear)
RCA Cord
(Video)
(Yellow)
(Video)
(Yellow)(L) (White) (L)
(White)
(R) (Red) (R) (Red)
Remote-Out Lead
(Black)
Remote-Out Lead
(Black) Camera Input Terminal
(Yellow)DIN Connector DIN Cord (black)
DVD ChangerCX-DH801W
(option)
Battery Lead
(Yellow) To the car battery, continuous +12 V DC
Power Lead (Red) (not used)
Power Lead (Red)
To ACC power, +12 V DC. Ground Lead (Black)
To a clean, bare metallic part of the car chassis Note:¡There are two types of changer connections as follows. Observe the features for each before connection.
Type A: You can control the changer with the main unit. But the rear monitor does not display any images.
Type B: You can see images on the rear monitor. But the changer should be controlled independently.¡Refer to the operating instructions for the connected devices, in addition.
Power Connector
(Supplied with CX-DH801W)Remote-In (RCA)
Remote Control
Sensor Extension
Cord (option)
CQ-VD7001W
(Rear)
RCA Cord
(Video)
(Yellow)
(Video)
(Yellow) (L)
(White)
(L) (White)(R) (Red) (R) (Red)DIN Cord (not used)Remote Control
Sensor Extension
Cord (option)
A
B 
						

							69
CQ-VD7001W
68
CQ-VD7001WElectrical Connections 
(continued)
(Video)
(Yellow)
REVERSE
PRN
D
2
L
Panasonic
CAMERA-IN
Connecting the Reverse LeadIf using an optional rear view camera, the reverse lead must
be connected.
Connect the reverse lead (violet/white stripe) to the positive (+)
lead of the reverse lamp (the lamp with a clear lens that lights
when the transmission gear is shifted into the reverse position).
Note:
¡Connect the reverse lead after cutting the terminal at the end.
¡Use a Reverse Extension Cord 
!4
if needed.
Connection with Rear View Camera
Rear View Camera (option)
RCA Cord(option)
Rear View Camera
Control Unit (option)
CQ-VD7001W
(Rear)
(Video)
(Yellow)
!3
Power Connector
Reverse lamp
Clip connector
(option)BatteryCar chassis
Transmission gear
!4
Reverse Extension Cord
(Violet/white stripe) Reverse Lead
(Violet/white stripe)Camera Input
Camera Input Terminal(Yellow)
Check the reverse lamp.
Take it out of the back of
the tail lamp mount.
Note:¡Refer to the operating instructions for the connected devices, in addition.
INTELLIGENT SYSTEM
BS G-CODE
POWER
VTR-INConnection with Rear Monitor
Note:¡Refer to the operating instructions for the connected devices, in addition.¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in
order to establish a proper connection.
VIDEO-OUT
COLOR LCD MONITOR
VM1500
Panasonic
STAND BY (R)
ON (G)
CQ-VD7001W
(Rear)
RCA Cord
(option)
(R) (Red) (R) (Red)
(L) (White) (L) (White)
(Video) (Yellow) (Video) (Yellow)
Example:
Example:
Rear Monitor
e.g. CY-VM1500EX (option)
Video Input Audio Right
Audio Left
Connection with VCR or Camcorder
CQ-VD7001W
(Rear)
(R)
(Red)(L)
(White)
(Video)
(Yellow)
VCR (option)
Camcorder (option)
(R) (Red)
(L) (White) (Video) (Yellow)
RCA Cord
(option)
Video Output
Audio Left
Audio Right
Note:¡Refer to the operating instructions for the connected devices, in addition.¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in
order to establish a proper connection.
Caution
¡For people sitting in the front seats, please
enjoy only audio during driving. 
						

							7071
CQ-VD7001W
CQ-VD7001W
SpecificationsGeneral¡Power supply : 12 V DC (11 V – 16 V), test
voltage 14.4 V, negative
ground
¡Current consumption : Less than 10 A (during disc
playback)
¡Maximum power output
:50 W x 4 ch
¡Compatible speaker 
impedance : 4 Ω
¡Video input signal : Composite video signal, 1.0
Vp-p (75 Ω)
¡Audio input sensitivity : 2 Vrms
¡Video output signal : Composite video signal, 1.0
Vp-p (75 Ω)
¡
Pre-Amp output voltage
:2 Vrms
¡
Pre-Amp output impedance
:Less than 600 Ω
¡Dimensions (W x H x D) : 178 x 50 x 165 mm
¡Weight : 2.4 kg
FM stereo radio¡Frequency range :
87.5 MHz – 108 MHz
¡Usable sensitivity :
12.2 
dBf
¡Stereo separation :
40 dB (1 kHz)
¡S/N ratio :
63 dB
AM stereo radio¡Frequency range :
531 kHz – 1 602 kHz
¡Usable sensitivity :
25 
dB/µV
¡Image rejection ratio :
50 dB
Audio section¡Output voltage/Impedance : 2 Vrms/600 Ω
¡Frequency characteristics 
(when “LARGE” is selected)
Front L/R, Center, Rear 
(surround) L/R : 20 Hz – 20 kHz (±1 dB)
¡Delay time
• 
Dolby DigitalCenter : 0 – 5 ms
Rear (surround) L/R : 0 – 15 ms
• Dolby Pro Logic
Rear (surround) L/R : 15 – 30 ms
• Distortion
Front L/R (1 kHz, 0 dB, PCM input)
:0.01 %
¡Dynamic range : 96 dB (during CD playback)
¡S/N ratio : 100 dB (during CD playback)
Monitor¡Liquid crystal panel : 7”wide
¡Screen dimensions 
(W x H x D) : 154 x 87 x 177 mm 
¡Number of pixels : 336 960 pixels (234 vertical x
480 horizontal x 3)
¡Valid pixel ratio : Over 99.99%
¡Display method : Transparent color filter format
¡Drive method : TFT (Thin Film Transistor)
active matrix format
¡Light source : Internal light (Built-in small
fluorescent lamp)
Note:
¡Specifications and the design are subject to modification without notice due to improvements in technology.
¡Some figures and illustrations on this manual may be different from your product.