Panasonic Electronic Board Ub 780bp Operating Instructions

Included AccessoriesCheck that all of the following items are included with your elite Panaboard.
In the event that an item is missing, please contact your dealer.
List of AccessoriesUSB Cable
(5 m [16 ft. 4  7
/8  in.])1Software CD-ROM1AAA Battery (LR03)
(Disposable)1Electronic Pen1Penpoint
(Replacement)2
Operating Instructions
(For Basic Operations) (this document)
1
Warranty1
Note
•Stand is sold separately.
• Store the extra penpoint along with this operating manual.
• The warranty may not be included...

Names and Uses of the Parts
Screen Front ViewNotice•The elite Panaboard is designed exclusively for projector images. Do not write on the screen board
with a white-board marker.12Operating Instructions (For Basic Operations)UsagePosition Sensor
Detects the position of the electronic pen. Do 
not block the sensor while operating the elite
Panaboard.
Screen Board
Project the contents of a computer screen using a 
projector.
Pen Tray
Push the center of the door to open the pen tray, 
which can hold up to 2...

Electronic Pen
Notice•Use the electronic pen by holding it at a right angle to the screen board.
Holding it at an angle can cause its position to be read incorrectly.
• Do not use multiple pens at the same time. This can result in erroneous operation.
• Do not push the penpoint while holding the pen close to the elite Panaboard. Doing so can cause
erroneous behavior.
Note
•The electronic pen switches to power-save mode after about 30 minutes.
• When waking up the pen from power-save mode by pushing the...

Inserting (Replacing) Batteries1. Remove (replace) the battery cover.
•When replacing the cover, follow the procedure in
reverse.
2. Insert (exchange) the battery and replace the
cover.
• Make sure to use a AAA alkaline battery, and
ensure that 
 and  face the correct
directions.
14Operating Instructions (For Basic Operations)Usage     

Connecting External Components1.Connect the elite Panaboard to a computer using the USB cable (included).
• Be sure the elite Panaboard software is installed on the computer before connecting it to the elite
Panaboard.
• elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port.
Computer: Plug the A connector (larger connector) into a USB port on the computer.
• Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation.
2.Connect...

Moving the elite Panaboard When Using the Stand (Sold Separately)1.Disconnect the USB cable from the elite Panaboard.
2. Release the locks on the casters.
3. Move the elite Panaboard, avoid banging or shaking the board.
Notice
•Always move the elite Panaboard with 2 people.
• Do not drag or step on the cable.
4. Lock the casters.
16Operating Instructions (For Basic Operations)Usage 

Installing the elite
Panaboard software
You need to install the elite Panaboard software on the
computer that will be used with the elite Panaboard.
To install the elite Panaboard software, follow the
procedure below.
Notice
•Do not connect the USB cable until the
installation is completed.
• Do not connect more than 1 elite Panaboard to
the same computer.
(Doing so can cause erroneous behavior on the
computer.)
1. Turn on your computer and start the Windows
operating system.
• Log into an account with...

Setting the Projector
Set up your projector as instructed below.
About Positioning the Image
• When you are projecting an image, make sure that
the edge of the projected image is at least 5 mm
( 1
/4  in.) from the screen frame. The electronic pen
may not function correctly within 50 mm (2 in.) of the
position sensor in the upper-left corner of the screen
board.Project the Image as a Rectangle• Adjust the location of the projector to project at a
right angle with the elite Panaboard.18Operating...

•If the image is projected trapezoidally, the
position of the electronic pen may not be read
correctly. Adjust the projector so that the
projected image is a rectangle. Refer to your
projector's documentation for information on
adjusting the projected image.
Set the Proper Resolution
• Set your computer's and projector's resolutions to
the most appropriate setting.
If the resolution is not set properly, the image will be
difficult to see. Particularly, if the projector's
resolution is...

Starting the elite
Panaboard software and
Performing Calibration
1. Connect the elite Panaboard to your computer
with the USB cable.
• The elite Panaboard software starts
automatically.
• When you start the elite Panaboard software for
the first time, the calibration screen is displayed.
• Restart your computer if you are prompted to do
so. After the computer has restarted, connect
the elite Panaboard to your computer with the
USB cable.
2. Perform calibration.
3. Press the electronic pen at a right...