Panasonic Electronic Board UB-T780 Operating Instructions

When disposing of the battery, cover the
battery contacts with insulation (ex. tape).
Direct contact with other
 batteries may re-
sult in leaking, fire, or explosion. Do not solder the battery, as it may result
in the battery leaking, generating heat, or
bursting.
Power
When the unit is not used over an exten-
ded period of time, switch it Off and unplug
it. If an unused unit is left connected to a
power source for a long period, degraded
insulation may cause electric shock, cur-
rent leakage or fire....

Safety Information (For
United Kingdom Only)
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 5 amp. fuse is fitted in this plug.
 Should the fuse need
to be replaced please ensure that the replacement fuse
has a rating of 5 amps. and that it is approved by ASTA
or BSI to BS1362. Check for the ASTA mark   or the
BSI mark   on the body of the fuse. If the plug contains
a removable fuse cover you must ensure that it is
refitted when the fuse is replaced. If...

Included Accessories
Check that all of the following items are included with your elite Panaboard.
In the event that an item is missing, please contact your dealer.
List of Accessories Power Cord
(3 m [9 ft. 10  3
/8 in.]) 1 USB Cable
(5 m [16 ft. 5  3
/8in.]) 1 Software CD-ROM 1
AAA Battery (LR03)
(Disposable) 1 Electronic Pen 1 Penpoint
(Replacement) 2
Operating Instructions
(For Basic Operations) (this document) 1 Warranty 1
Note
•The illustration of the power cord shown above is for the United...

Names and Uses of the Parts
Screen
Front View Rear View
12 Operating Instructions (For Basic Operations)
UsagePosition Sensor
Detects the position of the electronic pen. Do 
not block the sensor while operating the elite
Panaboard.
Screen Board
Project the contents of a computer screen using a 
projector.
Power Switch
Pen Tray
Push the center of the door to open the pen tray, 
which can hold up to 2 electronic pens.
Status LEDs
Left: Power LED (green)
Lights green when the power is on.
Right: Error LED...

Notice
•The elite Panaboard is designed exclusively for projector images. Do not write on the screen board
with a white-board marker. If you write on the screen board with a white-board marker, you cannot
erase it with a standard eraser. Use a commercially available melamine foam eraser to erase.
Electronic Pen Notice
•Use the electronic pen by holding it at a right angle to the screen board.
Holding it at an angle can cause its position to be read incorrectly.
• Do not use multiple pens at the same...

Inserting (Exchanging) Batteries
1. Remove (replace) the battery cover. •
When replacing the cover, follow the procedure in
reverse. 2. Insert (exchange) the battery and replace the
cover.
•
Make sure to use a AAA alkaline battery, and
ensure that   and   face the correct direc-
tions. 14 Operating Instructions (For Basic Operations)
Usage     

Connecting External Components
1.Set the power switch to "O" (OFF), connect the power cord (included) to the elite Panaboard, and
plug the power cord into an AC outlet. •
Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is
easy to unplug.
• If you are using the optional stand, plug the power cord into the AC inlet, and secure the cord
as shown in the illustrations below.
When attaching the power cord down-
ward. When attaching the power cord along the...

2.
Connect the elite Panaboard to a computer using the USB cable (included).
•elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port.
Computer: Plug the A connector (larger connector) into a USB port on the computer.
• Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation. 3.
Connect the computer to a projector.
•For instructions on connecting your computer and projector, refer
 to the respecting instruction manuals.
About...

Installing the elite Pana-
board software
You need to install the elite Panaboard software on
 the
computer that will be used with the elite Panaboard.
To install the elite Panaboard software, follow the
procedure below. Notice
•Do not connect the USB cable until the
installation is completed.
• Do not connect more than 1 elite Panaboard to
the same computer.
(Doing

 so can cause erroneous behavior on the
computer.)
1. Turn on your computer and start the
Windows *1
 operating system.
• Log into an...

Setting the Projector
Set up your projector as instructed below.
About Positioning the Image
•
When you are projecting an image, make sure that
the edge of the projected image is at least 5 mm
(1
/
4 in.) from the screen frame. The electronic pen
may not function correctly within 50 mm (2 in.) of the
position sensor in the upper-left corner of the screen
board. Project the Image as a Rectangle
•
Adjust the location of the projector to project at a
right angle with the elite Panaboard. •
If the image is...