Panasonic Electronic Board Ub T880 Operating Instructions

							11
Operating Instructions
For Your Safety
1
Operating Safeguards
Battery
Safety Information (For 
United Kingdom only)
This appliance is supplied with a moulded three pin 
mains plug for your safety and convenience.
A 5 amp fuse is fitted in this plug. Should the fuse need 
to be replaced, please ensure that the replacement 
fuse has a rating of 5 amps and that it is approved by 
ASTA or BSI to BS1362. Check for the ASTA mark   
or the BSI mark   on the body of the fuse. If the plug 
contains a removable fuse cover, you must ensure that 
it is refitted when the fuse is replaced. If you lose the 
fuse cover the plug must not be used until a 
replacement cover is obtained. A replacement fuse 
cover can be purchased from your local Panasonic 
Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE 
FOR THE SOCKET OUTLET IN YOUR PREMISES, 
THEN THE FUSE SHOULD BE REMOVED AND THE 
PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL 
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO 
ANY 13 AMP SOCKET.
If a new plug is to be fitted, please observe the wiring 
code as shown below. If in any doubt, please consult a 
qualified electrician.
WARNING
This appliance must be earthed.
IMPORTANT
The wires in this mains lead are coloured as 
follows:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
After installing or moving the unit, lock the 
casters and set the fall-prevention 
extension legs.
If the unit falls down or gets damaged, 
turn the unit off and unplug the power 
cord. Otherwise, it may cause fire or 
electric shock.
Do not lean against the screen or on the 
cover (lower), even if the unit is mounted 
on the wall.
When the unit is not used over an 
extended period of time, take the 
batteries out of the unit. Otherwise, the 
batteries may leak. Do not use the leaked 
batteries.
Locking the 
casters
(Push to lock)
UB-T880-PJQXC0337ZA_mst.book  11 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							For Your Safety
12 Operating Instructions
As the colours of the wire in the mains lead of this 
apparatus may not correspond with the coloured 
markings identifying the terminals in your plug, 
proceed as follows.
The wire that is coloured GREEN-AND-YELLOW must 
be connected to the terminal in the plug which is 
marked with the letter E or by the Earth symbol   or 
coloured GREEN or GREEN-AND-YELLOW.
The wire that is coloured BLUE must be connected to 
the terminal in the plug that is marked with the letter N 
or coloured BLACK.
The wire that is coloured BROWN must be connected 
to the terminal in the plug which is marked with the 
letter L or coloured RED.Precautions
Any changes or modifications not expressly approved 
by the party responsible for compliance could void the 
user’s authority to operate this device.
About Using the Battery
If a battery is used improperly, the battery may leak, 
causing corrosion of the unit, or it may burst. To 
prevent this, always follow the precaution given below.
•If the electronic pen ceases to function because the 
battery has run out, remove it immediately and 
dispose of it according to local regulations. Leaving a 
drained battery in the electronic pen may result in 
leakage.
About Disposing of the BatteryHow to replace the fuse:Open the fuse 
compartment with a 
screwdriver and 
replace the fuse and 
fuse cover.
Após o uso as pilhas / baterias 
contidas neste produto poderão 
ser dispostas em lixo doméstico.
For Brazil
For Taiwan (台灣)
UB-T880-PJQXC0337ZA_mst.book  12 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							13
Operating Instructions
For Your Safety
1
Other Information
Usage Note
Operating the elite Panaboard near electrical 
appliances may cause interference. Move away 
from the electrical appliances such as TVs, radios, 
cordless phone, or wireless devices.
MEDICAL
Consult the manufacturer of any personal medical 
devices, such as pacemakers, to determine if they 
are adequately shielded from external RF (radio 
frequency) energy. (The unit operates in the 
frequency range of 2.402 GHz to 2.481 GHz, and 
the power output level is 0.001 watts.) Do not use 
the unit in health care facilities if any regulations 
posted in the area instruct you not to do so. 
Hospitals or health care facilities may be using 
equipment that could be sensitive to external RF 
(radio frequency) energy.
For European Union (EU)
Panasonic System Networks Co., Ltd. declares 
that this equipment is in compliance with the 
essential requirements and other relevant 
provisions of Radio & Telecommunications 
Terminal Equipment (R&TTE) Directive 1999/5/EC.
Declarations of Conformity for the relevant 
Panasonic products described in this manual are 
available for download by visiting:
http://www.doc.panasonic.de
Contact to Authorised Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
No responsibility will be
 taken by our company 
with respect to consequences resulting from the 
use, damage or both of the equipment.
UB-T880-PJQXC0337ZA_mst.book  13 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
14Operating Instructions
Usage
Included Accessories
Check that all of the following items are included with your elite Panaboard.
In the event that an item is missing, please contact your dealer.
List of Accessories
* A 2.4 GHz USB Wireless Adaptor is preinstalled on the elite Panaboard.FCC ID: ACJ5Z6UE-608049 / IC: 216A-UE608049
Note
•The illustration of the power cord shown above is for the United States. The shape of the plug may vary 
depending on country/area.
•Stand is sold separately.
•Store the extra penpoint along with this operating manual.
•Replacement penpoints are available for purchase separately (page 34).
•The warranty may not be included depending on country/area.
About Using the DVD-ROM
Power Cord
(3 m [9 ft. 10
1/8in.]) 1 USB Cable
(5 m [16 ft. 47/8in.]) 1 Software DVD-ROM 1
AAA Battery (LR03) (Disposable) 1Electronic Pen1 Penpoint
(Replacement) 1
Operating Instructions (this document) 1W
arr a nty1 2.4 GHz USB 
Wireless Adaptor* 1
To prevent damage to the DVD-ROM:
•Do not touch or write on the surface of the disc.
•Do not leave the disc out of the protective case.
•Do not leave the disc in the direct sunlight or near heat sources.
•Do not place heavy objects on the disc case or drop the case.
•To clean the disc, hold the disc by its edges and wipe it from the center to the edges with a dry, soft cloth.
UB-T880-PJQXC0337ZA_mst.book  14 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
15Operating Instructions
1
Names and Uses of the Parts
Screen
Notice
•The operation of external devices connected via the USB hub is not guaranteed.
•External devices connected via the USB hub that require a lot of power, such as scanners or CD/
CD-Rs, may not operate properly. For more information, please consult the relevant dealer.
•When the elite Panaboard is used while peripherals connected to the USB hub are operating, the 
response of the elite Panaboard may be delayed and the electronic pen may malfunction. If such 
problems occur, connect the peripherals directly to the computer.
Note
•The elite Panaboard detects a change in electrostatic capacitance when touched by your finger. For 
this reason, it may not react to fingernails, gloved hands, or the electronic pen when a glove is worn.
•If you touch multiple points in a close area (within 10 cm [4 in.]), this may be recognized as a single 
point, or freehand lines may be drawn connected or intersecting.
Screen Board
Detects the position of your finger or the electronic pen.
Project the contents of a computer screen using a projector.
Error LED (red)
Blinks red when an error occurs. Power Switch/Power LED (green)
Turns the elite Panaboard on or off each time the power switch is pressed.
Lights green when the power is on.
Pen Tray
Push the center of the door to open the pen tray, which can hold the electronic 
pen.
USB Speaker
Outputs sound from a computer or the audio input port in stereo.
Vo l u m e  D i a l
Adjusts the volume of the speaker.
External Audio Input Port
Connect the audio output port of a VCR or DVD player etc. to this port and hear sound through the 
USB speaker.
USB Hub (2 Ports)
You can connect external devices directly to the elite Panaboard using these ports (page 20).
USB Port
Directly connect a computer using a USB cable (included).
Power Cord AC Inlet Power Inlet for Optional Devices
Is for optional elite Panaboard accessories only. Do not use this inlet with other devices.
UB-T880-PJQXC0337ZA_mst.book  15 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
16Operating Instructions
Electronic Pen
Note
•The up and down buttons can be used in a range of approximately 10 m (approximately 30 ft.) from the 
elite Panaboard (without obstructions).
Electronic Pen Features
Black/Red/Blue/Green Draws with a marker in the selected color.
Marker line thickness and other settings can be specified in the Drawing 
Menu.
Eraser Erases marker lines that you have drawn.
Eraser size and other settings can be specified in the Drawing Menu.
Yellow/Yellowish Green/
Pink Highlights with a highlighter in the selected color.
Highlighter line thickness and other settings can be specified in the Drawing 
Menu.
Low-Power Mode Puts the electronic pen in low-power mode.
The pen detects motion to turn itself on or off automatically. To conserve 
battery power, put the pen in low-power mode before carrying it while 
walking, when it is not in use.
Selector Dial
Selects features of the electronic pen.
Status LED (green)
Lights when the electronic pen power is on.
Blinks when the electronic pen battery is low.
Prepare a new battery and replace the old battery soon.
Up Button
Performs the same function as pressing the Page Up key on 
a computer by remote control.
Down Button
Performs the same function as pressing the Page Down key 
on a computer by remote control.
Battery Cover
Penpoint Penpoint Cover Menu Button
Hold this button and touch the screen board with the pen to 
display the Drawing Menu (page 26). Strap Loop
For attaching straps, if desired.
(No strap is included. Use a strap from which the cord will 
detach if excessive force is applied.)
UB-T880-PJQXC0337ZA_mst.book  16 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
17Operating Instructions
1
Notice
•When the electronic pen and your finger are used simultaneously, the elite Panaboard can not 
recognize these separately. Wait 1 second or more when changing between your finger and the 
electronic pen. When changed in a shorter time or when the electronic pen and your finger touch 
simultaneously, the result is according to which one the elite Panaboard recognized first.
•Confirm that the status LED lights when using the electronic pen.
•To avoid operating errors, do not touch the penpoint when the electronic pen is not in use.
Inserting (Replacing) Batteries
Registering the Electronic Pen
The elite Panaboard automatically detects electronic pens within approximately 10 m (approximately 30 ft.), 
but if other electronic whiteboards are nearby, electronic pens for those whiteboards may be detected 
accidentally. Similarly, other electronic whiteboards may detect electronic pens for the elite Panaboard. In the 
following cases, register the electronic pen to the elite Panaboard.
•Buttons on the electronic pen are unresponsive
•The elite Panaboard responds to the electronic pen as if you were touching the elite Panaboard with your 
finger
•The elite Panaboard responds as if you were operating it, but you are not
•elite Panaboard operation is erratic
Once you register an electronic pen, it cannot be used with another electronic whiteboard. (The whiteboard 
responds as if you were touching it with your finger instead of the electronic pen.) 
To use registered electronic pens with another electronic whiteboard, unregister the pens.
See “Registering the Electronic Pen” and “Unregistering the Electronic Pen” in “Software Help” for 
instructions on registering and unregistering the electronic pen.
For details on accessing the help information, see “Viewing the Help of the Software” (page 27).
1.Unlock the battery cover ( 1
), 
and open the cover ( 2
).
•When replacing the cover, follow the procedure in 
reverse.
2.Insert (replace) the battery, and then 
reattach the cover and lock it.
•Make sure to use a AAA alkaline battery, and 
ensure that  +
 and  -
 face the correct directions.
•Dispose of expired batteries quickly, by covering 
the terminals in tape and following the disposal 
regulations in your country/area.
UB-T880-PJQXC0337ZA_mst.book  17 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
18Operating Instructions
Connecting External Components
1.Connect the power cord (included) to the elite Panaboard, and plug the power cord into an AC 
outlet.
•Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is 
easy to unplug.
•If you are using the optional stand, plug the power cord into the AC inlet, and secure the cord as 
shown in the illustrations below.
•About Grounding
If you cannot connect the grounding line, contact your dealer. The cost of installing a grounding 
connection is not included in the price of the elite Panaboard.
•The included power cord is exclusively for use with the elite Panaboard. Do not use it with any 
other devices.
Power Cord
(Included)
When attaching the power cord downward. When attaching the power cord along the lower side of the elite Panaboard.
UB-T880-PJQXC0337ZA_mst.book  18 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
19Operating Instructions
1
2.Connect the elite Panaboard to a computer using the USB cable (included).
•elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard’s USB port. 
Computer: Plug the A connector (larger connector) into a USB port on the computer.
•Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation.
Notice
•Do not connect the elite Panaboard to a computer via USB unless elite Panaboard software/book is 
installed. 
Only connect the USB cable after following the steps in “Installing the elite Panaboard software/
book” (page 22) to install the software.
3.Connect the computer to a projector.
•For instructions on connecting your computer and projector, refer to the respecting instruction manuals.
To USB Port USB Cable
(Included)
Video Cable AC
AC
Computer
Projector
UB-T880-PJQXC0337ZA_mst.book  19 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
20Operating Instructions
Connecting External Devices
1.Connect the external device to the elite Panaboard using a USB cable (sold separately).
•elite Panaboard: Plug the A connector (larger connector) into the elite Panaboard’s USB port. 
External device: Plug the B connector (smaller connector) into a USB port on the external device.
About the Usage Location
•Do not place the elite Panaboard where it is directly exposed to sunlight.
•Do not use the elite Panaboard in a location less than 10°C (50°F) or in a location subject to extreme 
changes in temperature.
Note
•The elite Panaboard may not work properly when used in one of the above locations.
•Operating the elite Panaboard near electrical appliances may cause interference. Move away from the 
electrical appliances.
To USB Port USB Cable
(Sold Separately)
MFP
Flatbed 
Scanner To USB Port
UB-T880-PJQXC0337ZA_mst.book  20 ページ  ２０１０年５月１１日　火曜日　午後１時９分