Panasonic Electronic Board Ub T880 Operating Instructions

							Usage
21Operating Instructions
1
Volume Control
•The volume of the USB speaker on the elite Panaboard can be controlled using the Volume Dial, the 
volume of Windows, and the volume of the application being used. To adjust the volume, use the Volume 
Dial, or adjust the volume of the application.
Power Switch
•After turning the elite Panaboard off, wait more than 2 seconds before turning it back on.
Moving the elite Panaboard When Using the Stand (Sold Separately)
1.After confirming that the power is off, disconnect the power cord and USB cable.
2.Release the locks on the casters.
3.Move the elite Panaboard, avoid banging or shaking the board.
Notice
•Always move the elite Panaboard with 2 people.
•Do not drag or step on the cable.
4.Lock the casters.
UB-T880-PJQXC0337ZA_mst.book  21 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
22 Operating Instructions
Installing the elite 
Panaboard software/book
You need to install the elite Panaboard software/book 
on the computer that will be used with the elite 
Panaboard.
To install the elite Panaboard software/book, follow the 
procedure below.
Notice
•Do not connect the USB cable until the 
installation is completed.
•Do not connect more than 1 elite Panaboard to 
the same computer. 
(Doing so can cause erroneous behavior on the 
computer.)
1.Turn on your computer and start the Windows 
operating system.
•Log into an account with Administrator 
privileges.
2.Insert the included DVD-ROM into the 
DVD-ROM drive.
•The setup screen will be displayed.
•If the setup screen does not appear, select your 
DVD-ROM drive in Explorer and double-click 
[Menu.exe].
•In Windows Vista or Windows 7, if the Autoplay 
dialog box is displayed, click [Run Menu.exe].
3.When the “Welcome” screen has been 
displayed, click [Next].
4.When the “Model Selections” screen is 
displayed, click the type of device you are 
using.
5.When the “Menu” screen is displayed, click 
[Read Me First].
•After the system requirements are displayed, 
make sure that your computer meets the 
requirements.
6.Click [Install elite Panaboard] on the “Menu” 
screen.
7.If you agree to the terms in the “License 
Agreement”, click [Yes].
•In Windows Vista, if the “User Account Control” 
window is displayed, click [Continue] to continue 
with the installation.
•In Windows 7, if the “User Account Control” 
window is displayed, click [Yes] to continue with 
the installation.
UB-T880-PJQXC0337ZA_mst.book  22 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							23
Operating Instructions
Usage
1
8.When the following screen is displayed, 
confirm that the USB cable is not connected to 
your computer or the elite Panaboard, and 
click [OK].
•If the USB cable is connected to the elite 
Panaboard, disconnect the cable, and click [OK].
•If .NET Framework 3.0 or later is not installed, an 
installation screen will be displayed. Follow the 
on-screen directions to install these components.
9.When the installation wizard is displayed, 
follow the on-screen instructions and continue 
with the installation.
10.When installation has finished, click [Finish].
•Restart your computer if you are prompted to do 
so.
•The group [elite Panaboard] will be created in 
the [Panasonic] group in the program menu.
•The following items will appear in the [elite 
Panaboard] group:
– elite Panaboard software
– elite Panaboard book
– Electronic Pen Registration Tool
– Operating Instructions
– Software Help
– Download the latest version
Note
•To view the Operating Instructions, you must 
have Adobe® Reader® installed on your 
computer. If your computer is connected to 
the Internet, you can download Adobe 
Reader from Adobe’s web site.
UB-T880-PJQXC0337ZA_mst.book  23 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
24 Operating Instructions
Setting the Projector
Set up your projector as instructed below.
About Positioning the Image
•
When you are projecting an image, make sure the 
image is inside the screen frame.
Project the Image as a Rectangle
•
Adjust the location of the projector to project at a 
right angle with the elite Panaboard.
•If the image is projected trapezoidally, the position 
may not be read correctly. Adjust the projector so 
that the projected image is a rectangle. Refer to your 
projector’s documentation for information on 
adjusting the projected image.
Set the Proper Resolution
•
Set your computer’s and projector’s resolutions to 
the most appropriate setting.
If the resolution is not set properly, the image will be 
difficult to see. Particularly, if the projector’s 
resolution is lower than the computer’s, thin lines can 
appear cut or broken. Refer to your projector’s 
documentation for information on adjusting the 
resolution.
Do Not Look Directly into the Projector Lamp
•
When using a projector, try to avoid looking directly 
into the projector lamp. Doing so can hurt your eyes.
UB-T880-PJQXC0337ZA_mst.book  24 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							25
Operating Instructions
Usage
1
.
Setting Your System 
(Calibration)
About Calibration
Calibration refers to setting up the elite Panaboard and 
projector so that lines and comments drawn with your 
finger or the electronic pen are displayed in the correct 
position. Be sure to perform calibration before use.
After you have set up the elite Panaboard, project an 
image onto the screen board and use the elite 
Panaboard software installed on your computer to 
perform calibration.
After Calibration
Do Not Move the elite Panaboard or the 
Projector
•
The following changes will bring the position of 
projection out of alignment with the position of your 
finger or the electronic pen, and you will need to 
recalibrate the equipment.
– The location of the projector changed.
– The location of the elite Panaboard changed.
– The image area or placement was changed due 
to changes in the zoom, focus, etc.
– The resolution of the projector or the computer  changed.
•If you are using the elite Panaboard installed on a 
stand, be aware that accidentally hitting the elite 
Panaboard or pushing too strongly with the 
electronic pen while operating can move the stand’s 
position, which will result in misalignment of the 
projected image and the electronic pen’s position.
•Make sure to lock the stand’s casters when using the 
elite Panaboard, as failing to do so can cause 
misalignment.
Note
•To perform calibration, click the   icon in the 
notification area and click [Calibration] in the 
pop-up menu.
Starting the elite 
Panaboard software and 
Performing Calibration
1.Turn on the elite Panaboard.
2.Connect the elite Panaboard to your computer 
with the USB cable.
•The elite Panaboard software starts 
automatically.
•Once the elite Panaboard software starts up, the 
calibration screen is automatically displayed.
•Restart your computer if you are prompted to do 
so. After the computer has restarted, connect the 
elite Panaboard to your computer with the USB 
cable.
3.Calibrate the equipment by using your finger to 
touch the center of the indicated points in the 
order shown for about 2 seconds.
•Touch the screen board at a right angle with your 
finger.
•After you touch an indicated point correctly, the 
next point is shown automatically.
•When calibration has finished normally, a 
completion dialog box is displayed.
UB-T880-PJQXC0337ZA_mst.book  25 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Usage
26 Operating Instructions
4.Click [OK].
•If the elite Panaboard and projector are fixed so 
that they will not move (Wall mounted case), 
select the [Always use this calibration 
information.] check box, and click [OK] to skip 
calibration from the next time you start the elite 
Panaboard software.
•When calibration is finished, the   icon is 
displayed in the notification area. You can now 
use the elite Panaboard software.
•To display the Select Function Menu, click the 
Menu Start Tab (left side:   / right side:   ) on 
the screen with your finger.
•To display the Drawing Menu, touch the screen 
board while holding the menu button on the 
electronic pen.
Note
•For detailed information about using the elite 
Panaboard software, refer to the help menu. 
For details on accessing the help 
information, see “Viewing the Help of the 
Software” (page 27).
Exiting the elite Panaboard software
Click on the   icon in the notification area, and select 
[Exit] from the menu.
Example of the Select Function Menu
Example of the Drawing Menu
UB-T880-PJQXC0337ZA_mst.book  26 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							27
Operating Instructions
Usage
1
Viewing the Help of the 
Software
Follow the procedure below to view the help of the 
software installed on your computer.
1.Turn on your computer and start Windows.
2.Open “Software Help” from the Start menu. 
([Start]  →   [All Programs] →    [Panasonic]  →   [elite 
Panaboard]  →   [Software Help])
•General help information of the installed software 
is displayed.
Note
•To access the help information of elite 
Panaboard software and Electronic Pen, 
click the   icon in the notification area and 
select  [Help] from the pop-up menu.
•To access elite Panaboard book help 
information, select  [Help...] from the elite 
Panaboard book [Help] menu.
•We recommend that you view the help using 
Internet Explorer® 6.0 or later for Windows.
Uninstalling the elite 
Panaboard software/
book
If it is necessary to uninstall the elite Panaboard 
software/book, follow the procedure below.
1.Turn on your computer and start Windows.
•Log into an account with Administrator 
privileges.
2.Select [Add or Remove Programs] from the 
Control Panel.
•In Windows Vista or Windows 7, select [Uninstall 
a program].
3.Select Panasonic elite Panaboard, then remove 
it.
4.Follow the on-screen instructions.
5.When uninstallation is complete, restart your 
computer.
Download the Latest 
Software
Follow the procedure below to download the latest 
version of the software from the download web site.
1.Turn on your computer and start Windows.
2.On the Start menu, point to [All Programs]  →  
[Panasonic]  →   [elite Panaboard], and click 
[Download the latest version].
UB-T880-PJQXC0337ZA_mst.book  27 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Appendix
28Operating Instructions
Appendix
Daily Care
When cleaning the elite Panaboard or inside the elite Panaboard, make sure to switch off the power and 
unplug the power cord from the AC outlet.
Cleaning the elite Panaboard
Gently wipe the elite Panaboard with a soft, moist 
cloth.
Notice
•The elite Panaboard is designed exclusively for 
projector images. 
To remove marks written with a whiteboard 
marker or stubborn stains, use whiteboard 
cleaner or neutral household detergent diluted 
with water.
•Do not use thinner, benzene, or abrasive 
chemicals to clean. 
(Doing so can result in discoloration.)
Replacing the Battery in the 
Electronic Pen
When the electronic pen battery is low, the pen status 
LED blinks. Continued use of the electronic pen can 
lead to poor performance. Replace the battery as soon 
as possible. See “Inserting (Replacing) Batteries” 
(page 17) for details on replacing the battery.
•Dispose of expired batteries quickly, by covering the 
terminals in tape and following the disposal 
regulations in your country/area.
Após o uso as pilhas / baterias 
contidas neste produto poderão 
ser dispostas em lixo doméstico.
For Brazil
For Taiwan ( 台灣)
UB-T880-PJQXC0337ZA_mst.book  28 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							29
Operating Instructions
Appendix
1
Replacing the Penpoint of the 
Electronic Pen
As the penpoint of the electronic pen becomes worn, 
the penpoint will no longer slide easily across the 
surface. Continuing to use the electronic pen in this 
condition may make the screen dirty and cause 
malfunction. Replace the penpoint with a new one as 
soon as possible.
1.Remove the penpoint cover.
2.Remove the old penpoint and attach the new 
one.
3.Reattach the penpoint cover.
O
ld
 P
e
n p
o i
n
t
N ew
 P e
n p
oin
t
UB-T880-PJQXC0337ZA_mst.book  29 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Appendix
30Operating Instructions
Troubleshooting
When experiencing problems, please refer to the table below for possible solutions. If the problem persists, 
contact your dealer.Symptom Possible cause and solution See page
The LEDs do not light 
when the power switch is 
turned on. Check that the power cord is properly plugged in.
→
If the problem persists, unplug the cord momentarily, wait about 
2 seconds, and plug it in again. —
Error LED (red) is 
blinking. Turn off the power, and turn it on.
→
If the problem persists, contact your dealer. —
The computer does not 
recognize the elite 
Panaboard.
•The elite Panaboard and your computer are not connected.
→ Securely connect the elite Panaboard and your computer 
using a USB cable.
•The USB cable is connected to a USB hub.
→Do not connect the elite Panaboard through a USB hub. —
The connection between 
the computer and the 
elite Panaboard is 
unexpectedly lost. Check that the elite Panaboard is in an operable state, and that the 
USB cable is properly connected.
—
The elite Panaboard 
response is delayed. Other applications or anti-virus software are active.
→
Shut down the other applications and anti-virus software. 5
The point of control is out 
of alignment with your 
finger or the electronic 
pen. The projected image is misaligned.
→
Perform the calibration again. 25
Lines or comments 
drawn with your finger 
are not shown on the 
computer screen.
•You are touching the screen board with a part of your hand other 
than your finger.
→ Use only your finger tip to touch the screen board.
•You are touching too lightly with your finger.
→Touch the screen board more firmly. —
UB-T880-PJQXC0337ZA_mst.book  30 ページ  ２０１０年５月１１日　火曜日　午後１時９分