Panasonic Ey7542 Operating Instructions Manual

Multi-Impact & Drill Driver
Entraînement perceuse & percussions multiples
Pistola taladradora y múltiples impactos
Operating Instructions
Instructions d’utilisation
Manual de instrucciones
 Model No: EY7542
IMPORTANTThis manual contains safety information. Read manual completely before f\
irst using this product and save this manual for future use.
IMPORTANTCe mode d’emploi contient des informations sur la sécurité. Lis\
ez-le en entier avant d’utiliser le produit et conservez-le pour référence....

-  - 
Index/Index/Indice
English: Page 3 
Français:  Page 17  Español:  Página 33
FUNCTIONAL DESCRIPTION
DESCRIPTION DES FONCTIONS
DESCRIPCIÓN FUNCIONAL
(P)
(R)
(S)
(A)
(F)
(E)
(C)
(D)
Ni-MHNi-Cd
(G)
(G)
(H)
(I)
(J)
(O)(N)(M)
(L)(K)
(A)6.35 mm (1/4") hex quick connect chuckMandrin de connexion rapide hexagonal de 6,35 mm (1/4")Mandril hexagonal de conexión rápida de 6,35 mm (1/4")
(B)Clutch handlePoignée de l’embrayageMango de embrague
(C)Impact/Drill driver switchCommutateur de...

- 3 - 

I.  INTRODUCTION
This  tool  is  the  Multi-Impact  &  Drill 
driver  that  has    operation  modes, 
“Impact  Driver  mode”  and  “Drill  Driver mode”. The modes can be selected by sliding the impact/drill driver switch.
II. GENERAL  SAFE -
TY RULES
 WARNING! Read all instructions
Failure  to  follow  all  instructions  listed below  may  result  in  electric  shock,  fire and/or  serious  injury.  The  term  “power tool”  in  all  of  the  warnings  listed  below refers  to  your  main...

- 4 -  

7) I f  d e v i c e s  a r e  p r o v i d e d  f o r  t h e connection  of  dust  extraction  and collection  facilities,  ensure  these are connected and properly used. 
Use of these devices can reduce dust related hazards.
Power Tool Use and Care
1) Do not force the power tool. Use the correct  power  tool  for  your  applica-tion.
The  correct  power  tool  will  do  the  job better and safer at the rate for which it was designed.
) 
Do  not  use  the  power  tool  if  the switch does...

- 5 - 

)   Wear  ear  protectors.  Exposure  to noise can cause hearing loss.
3)   Be  aware  that  this  tool  is  always  in  an operating  condition,  since  it  does  not have  to  be  plugged  into  an  electrical outlet.
4)  If the bit becomes jammed, immediate-ly  turn  the  trigger  switch  off  to  prevent an overload which can damage the bat-tery pack or motor. Use reverse motion to loosen jammed bits.
5)  
Do  NOT  operate  the  Forward/Reverse lever  when  the  trigger  switch  is  on....

- 6 -  

a. pins  on  plug  of  extension  cord  are the  same  number,  size  and  shape as those of plug on charger.
b.  extension  cord  is  properly  wired 
and in good electrical condition.
c. wire size is large enough for ampere rating of charger as specified below.
RECOMMENDED MINIMUM AWG SIZE OFEXTENSION CORDS FORBATTERY CHARGERS
AC Input Rating.AmperesAWG Size of Cord
Equal to or greater thanBut less thanLength of Cord, Feet
550100150
018181816
8) Do  not  operate  charger  with...

- 7 - 

4. Pull the bit to make sure it does not come out.
5. To remove the bit, pull out the collar in the same way.
CAUTION:
• If  the  collar  does  not  return  to  its 
original  position  or  the  bit  comes  out when pulled on, the bit has not been properly  attached.  Make  sure  the  bit 
is properly attached before use.
Use 6.35 mm (1/4") hexagonal bits.To  ensure  proper  securement  of  the bit,  use  only  hexagonal  bits  with  9.5 mm (3/8") detent.
6.35 mm (1/4")9.5 mm...

- 8 -  

Reverse  Rotation  Switch 
Operation
 1. Push  the  lever  for  reverse  rotation. Check  the  direction  of  rotation  be-fore use.
   .  Depress the trigger switch slightly to 
start the tool slowly.
  3. After  use,  set  the  lever  to  its  center 
position (switch lock).
Selecting Mode
Select modeIntended useWork material
Impact driverFasteningBolt Nut
Driving
Wood screwMetal screwSelf-driving screwDrill driver mode with clutch func-tionDrilling
WoodMetal
 WARNING!
This  tool  must...

- 9 - 

• When  the  main  unit  is  held  by  the belt  hook,  avoid  jumping  or  running with it.  Doing so may cause the hook to slip and the main unit may fall.  T h i s  m a y  r e s u l t  i n  a n  a c c i d e n t  o r injury.
•  When  the  belt  hook  is  not  used,  be 
sure  to  return  it  to  the  storing  posi-t i o n .  T h e  b e l t  h o o k  m a y  c a t c h  o n something. 
  T h i s  m a y  r e s u l t  i n  a n  a c c i d e n t  o r 
injury.
• 
W h e n  t h e  u n i t  i s  h o o k...

- 10 -  

Caution : DO NOT STARE INTO BEAM.
Use  of  controls  or  adjustments  or  performance of  procedures  other  than  those  specified  herein may result in hazardous radiation exposure.
(2) Overheat warning lamp
Off (normal operation)
Flashing: Overheat
Indicates operation has been halted due to battery overheating.
The  overheating  protection  feature halts  driver  operation  to  protect  the 
b a t t e r y  p a c k  i n  t h e  e v e n t  o f  o v e r-
heating.  The  overheat  warning  lamp...