Panasonic EYFR02 Operating Instructions

Assembly Qualifier
Operating Instructions
Model No: EYFR02
IMPORTANTThis manual contains safety information. Read manual completely before f\
irst using this product and save this manual for future use. 

-  - 
Index
English: Page  3
FUNCTIONAL DESCRIPTION
(A)I/O connector
(B)Beeper
(C)Volume switch
(D)Fastening PASS indicator
(E)Antenna
(F)Fastening FAIL indicator
(G)Mounting holes
(H)Signal strength indicator
(I)Power indicator
(J)Key lock
(K)D-sub 9-pin female inch thread
(L)Power switch
(M)Power plug inlet
(N)Mode switching keys ()
(O)Power cord
(B)
(I)
(J)
(K)
(A)
(C)
(F)(E)(D)
(L)
(O)
(G)
(H)(M)
(M) 

- 3 -  
I. INTRODUCTION
Thank you for purchasing the Panasonic Assembly Qualifier. The AQ Wireless can monitor battery  tools.  In  its  simplest  form,  the AQ  Wireless  is  configured  to  monitor  a  tool  while  it's running, determine if the fastening process was successful, report the status of the fasten-ing, and perform counting functions.
How to Use This Manual
• Please  read  this  manual  completely  before  starting  to  use  your AQ  Wireless.  If  this  unit  is mishandled a fatal...

- 4 - 

II. BEFORE USING THE ASSEMBLY QUALIFIER
Downloading software
The  assembly  qualifier  is  configured  (relay  output  time,  frequency,  etc.)  by 
connecting  it  to  a  computer.  The  Device  Programmer  application  is  required  in 
order  to  do  this.  If  you  need  to  configure  the  assembly  qualifier,  the  software 
can be downloaded from the following URL:
http://●●●●●.●●●
Device Programmer system requirements
Read before use
• You may not be able to use the Device Programmer on...

- 5 -  

Hard disk
Ultra DMA-100 or better
At least 50 MB of space for installing the software
• When  recording  to  disk,  space  equal  to  at  least  twice  the  size  of  the  data  being 
created is required. 
•  An  error  may  occur  during  recording  if  the  compression  setting  is  enabled. 
Deselect  the  “Compress  contents  to  save  disk  space”  checkbox  in  the  hard 
disk’s “Properties.” 
Interface
Serial communications port (COM)
Other
Mouse or equivalent pointing device
Required...

- 6 - 

• Microsoft and Windows are registered trademarks or trademarks of Microsoft 
Corporation in the United States and other countries.
•  IBM  and  PC/AT  are  registered  trademarks  of  International  Business 
Machines Corporation.
•  Apple,  the Apple  logo,  Macintosh,  and  MacOS  are  registered  trademarks  of 
Apple Inc.
•  Intel, Pentium, and Celeron are registered trademarks or trademarks of Intel 
Corporation in the United States and other countries.
•  Screenshots  have  been  used  in...

- 7 -  

Installing the software
● Before installing the software, quit all other open applications. 
1.  Double-click “Panasonic Device Programmer.zip.”
2.  Follow the instructions on the screen to install the software.
● Restart the computer once the installation is complete.
Configuring settings with the software
1.  Connect the assembly qualifier to the computer.
• Use an RS-232C straight cable.
Using a serial RS-3C port to connect the assembly qualifierUsing a USB port to connect the...

- 8 - 

• File menu
1 Creates a new file.
2 Opens a previously created file.
3 Saves the current settings.
4 Saves the current settings as a new file.
5 Opens recently used files.
6 Exits the Device Programmer application.
• Product menu
EYFR021 Selects the assembly qualifier.  
(This setting does not need to be changed.)
2 Not used
• Tool menu
Configures the port used to connect the assembly 
qualifier to the computer.
1 Selects the port.
2 Sets the baud rate.  
Initial setting: 9600 

- 9 -  

• About menu
Allows you to check the software’s version. 
Installing the assembly qualifier
Installation method
Mount the assembly qualifier securely with screws using the four mountin\
g holes. 
NOTE
Before  mounting  the  assembly  qualifier,  test  it  where  you  plan  to  install  it  to  ensure 
that there are no communications issues. 
CAUTION
Verify  that  the  assembly  qualifier  is  not  affected  by  other  wireless  equipment  before 
mounting it. 

- 10 - 

III.	OPERATION
Registering the tool with the assembly qualifier
● Preparing the assembly qualifier
1.  Connect the power cord to the assembly qualifier.
.  Plug the power cord into a wall outlet.
3.  Turn on the assembly qualifier. 
 
All indicators will turn on and off, leaving only the power indicator on.
4.  Insert a mode switching key into the key lock and turn to the left. 
 
The power indicator will flash, and the assembly qualifier will enter to\
ol 
registration standby mode.
●...