Panasonic Kx T206e Installation Manual

11
System Connection Diagram
P
a
n
a
s
o
n
i
cPanasonicA
U
T
O
 
S
C
A
NAUTO SCAN10CH10CH
P
a
n
a
s
o
n
i
cPanasonic
PanasonicPanasonicELECTRONICMODULARSWITCHINGSYSTEM
2 CO Lines
Doorphone KX-T30865
Doorphone
6 Extensions
(one pair)
(two pair)(two pair)
(two pair)
(one pair) (one pair)KX-T7130
KX-T7050 Single Line Telephone
Cordless Phone
Telephone Answering
Machine with FacsimileKX-T7020to CO1 and CO2
Door Opener 

12
CO Line Connection
Wire SpecificationThe wire specifications are as follows:
WireSolid wire
Diameter of conductorø 0.4 – ø 0.65mm
Diameter with coatingø 0.66 – ø 1.05mm
ConnectionUse a 4-pin plug (included) to connect CO lines.
A single plug is able to connect two CO lines.  Use twisted pair cable.
1. Lift the transparent part.
2. Insert the required telephone wires into the holes of the plug.
Then press the transparent part back into the black part.
Note: Do not strip the wires.
Insert the wires all...

13
Extension Connection
Wire SpecificationThe wire specifications are as follows:
WireSolid wire
Diameter of conductorø 0.4 – ø 0.65 mm
Diameter with coatingø 0.66 – ø 1.05 mm
ConnectionUse a 4-pin plug (included) to connect extension lines.
There are 6 plugs to connect extensions to EXTN. 1 through EXTN. 6
jacks.
1. Lift the transparent part.
2. Insert the required telephone wires into the holes of the plug.
Then press the transparent part back into the black part.
Note: Do not strip the wires.
Insert...

14 Any single line telephone can be connected in parallel with a proprietary telephone.
ELECTRONICMODULARSWITCHINGSYSTEMP
O
W
E
R
Paralleled Telephone Connection
Notes
• The following features are not available for SLT connected in parallel:
Call Splitting
External Feature Access
Conference
4-conductor wiring cord
Connect pins “H”, “A”,
“B”, and “L”.2-conductor wiring cord
Connect pins “A” and “B”.
Master
socket Secondary
socket 

15
Installation of Optional Card and Unit
Doorphone (KX-T30865) Connection
2-conductor wiring cord
KX-T30865
Notes
•The doorphone adaptor is not required for KX-T206.
•To avoid howling, you must assign all extensions as “DISABLE” in the “#06/#76 Doorphone
Assignment (Day/Night)” program when you do not connect a doorphone.
•If howling occurs while using the doorphone feature, check the wiring.
•You can use cable holders to fix the wires.
Door Opener Connection
A user-supplied door opener can be connected...

16
DISA Card (KX-T20691) Connection
1. Disconnect the AC cord from the system.
2. Loosen the screws and remove the cover.3. Attach the DISA card to the marked connectors.
4. Replace the cover and secure the screws.
5. Connect the AC cord again.
CO2
CO 1
DOOR
PHONE
GROUND
EXTN.
5
EXTN.
3
EXTN
1E
X
T
N
.
6
E
X
T
N
.
4
E
X
T
N
.
2
D
P
H
P
O
W
E
R
ELECTRONIC MODULAR SWITCHING SYSTEM
The DISA feature allows an outside caller to have direct access to intercom calls.  System pro-
gramming is required.  See “#10...

17
Installation of Lightning Protectors
Overview
A lightning protector is a device to be installed on a CO line to prevent a dangerous surge from
entering the building and damaging equipment.
A dangerous surge can occur if a telephone line comes in contact with a power line.  Trouble due
to lightning surges have been showing a steady increase with the development of electronic
equipment.
In many countries, there are regulations requiring the installation of a lightning protector.
A lightning strike to a...

18
Installation of an Earth Rod
Notice
If you install an extension outside of the main building, the following precautions are recom-
mended:
(1) Install the extension wire underground.
(2) Use a conduit to protect the wire.
Note
•The lightning protector for an extension is different from that for CO.
(1) Installation location of the earth rod ...... Near the protector
(2) Check obstructions ................................ None
(3) Composition of the earth rod ................. Metal
(4) Depth of the...

19
Power Failure Transfer
In the event of a power failure, CO2 is connected to extension 22 automatically.
Note
•The system programmed data is protected by the factory provided lithium battery.
Starting the System
Plug the AC power cord into the system and an AC outlet.
•The power indicator of the system will light. 

20
General Programming Instructions
Default SettingThis system has a default factory setting.  If any of the program-
ming needs to be changed, you can change the setting by system
programming.
Required Telephone SetYou can use any of the following telephones for system program-
ming:
• Proprietary Telephone (PT): KX-T7130, KX-T7020, KX-T7050
• Single Line Telephone (SLT): tone type
All telephones (except KX-T7130) do not have display panels, so
you cannot check the setting you have made.  Therefore,...