Panasonic Kx-T2315 Integrated Telephone System Operating Instructions

							Battery Installation 
Three AA size batteries (UM-3) serve as the power source to retain the stored 
telephone numbers in memory. 
Remove the wall mount adaptor. 
Open the battery compartment 
cover. 
Insert the three AA size batteries 
observing the correct polarity. 
Replace the adaptor. 
NOTE: 
n To prevent loss of the stored telephone numbers, replace the batteries within 
10 minutes after removing the old ones. 
W Disconnect the telephone cord before opening the battery compartment 
cover. 
n Replace all the batteries once a year, or misoperation may occur. 
n Do not use Nickel-Cadmium batteries. 
BATTERY PRECAUTIONS: The batteries should be used correctly, otherwise, 
the unit may be damaged due to battery leakage. 
q Do not mix different types of batteries. 
q Do not charge, short-circuit, disassemble, heat or dispose in fire. 
n Remove all the batteries when replacing. 
4  
						

							Initial Settings 
5  
						

							Dialing Mode Selector 
Set to “Tone”. 
If dialing can not be done, set to “PULSE”. 
Ringer Volume Selector 
Set to “HIGH”. 
LOW: The ringing sound will be low. 
OFF: The telephone will not ring. 
Local Call Only Switch 
OFF: Local and long distance calls can 
be made. 
ON : The manual or automatic dialing 
operation of a number with more 
than 7 digits is not possible. 
Use a pencil or a bail-point pen to fill In the 
station directory with station name. (You can 
use the reverse side for writing, too.) 
ORemove the cover using an 
instrument with a pointed 
end, like a pen. 
6  
						

							Making and Receiving Calls 
Lift the handset. 
Dial the telephone number. 
Speak to the other party. 
l 
You can switch to the speakerphone at 
anytime by pressing the SP-PHONE 
button. You can replace the handset on 
the cradle. 
7  
						

							Press the SP-PHONE button. 
l 
The SP-PHONE indicator lights, 
Dial the telephone number. 
Speak to the other party. 
l 
You can also switch to the handset at 
anytime by lifting the handset. 
When finished, Press the 
SP-PHONE button again. 
l 
The SP-PHONE indicator light goes out 
n When the other party finds it difficult to hear your voice: 
Lower the sound level using the Speaker Volume Control or speak louder. 
n Absorbing echoes: 
Use in a room which has curtains or carpeting. 
n To avoid lost or broken conversation: 
If you and caller speak at the same time, parts of your conversation will be 
lost. To avoid this, speak alternately. 
8  
						

							Making and Receiving Calls (cont.). 
Lift the handset. 
Press the SP-PHONE button. 
or Speak to the calling party. 
Press the REDIAL button when 
the line is busy. 
l 
Pressing the REDIAL button enables 
you to redial once. 
9  
						

							Storing Phone Numbers 
n There are 20 memory stations, each station is capable of storing 16 digits 
n There are 8 Direct Call buttons, each capable of storing 16 digits. 
Each Dialing button serves as a memory station. 
Be sure that the handset is on the cradle and the SP-PHONE indicator is off 
and the batteries are installed. 
n Home Use 
Press the PROGRAM button 
until the STORE indicator lights. 
- 
Press the Station number. 
0 Phone numbers can be stored into 
memory stations m m to m p[ 
following the same procedure. 
Dial the telephone number. 
Press the AUTO/STORE button 
to store the number into 
memory. 
After storing all the numbers, 
press the PROGRAM button. 
l 
The STORE indicator goes out. 
IO  
						

							Storing Phone Numbers (cont.) 
H Home Use 
Press the PROGRAM button 
until the STORE indicator lights. 
Press the Direct Call button. 
Dial the telephone number. 
Press the AUTO/STORE button 
to store the number into 
memory. 
After storing all the numbers, 
press the PROGRAM button. 
l 
The STORE indicator goes out. 
11  
						

							W Office Use (PBX) 
Press the PROGRAM button 
until the STORE indicator lights. 
Press the Station number. 
l 
You may use the Direct call button 
instead of pressing the station number. 
Enter Line access n u m her for 
an example 9. 
Press the 
PAUSE button. 
Dial the telephone number. 
Press the AUTO/STORE button. 
After storing all the numbers, 
press the PROGRAM button. 
l 
The STORE indicator goes out.  
						

							Automatic Dialing 
Lift the handset, or press the 
SP-PHONE button. 
n To change a stored number, repeat the steps of “Storing Phone numbers”. 
n If the batteries are not installed, programming and speakerphone operation 
can not be done. 
Press the AUTO/STORE button. 
Press the Station number. 
(01 to 
20) 
Press the Direct Call button. 
13