Panasonic Kx-T7880 Wireless Phone Reference Guide

R 
Panasonic 
EFERENCE 
G UIDE 
- 
Please read the Imomm &mm INSTRUCU~NS on 
pages 20 through the buck cover before use. 
Read and understand all instructions. 
MODEL No. 
KX-T7880  

THANK YOUFORPURCHASING THE KX-T7880. 
Contents 
FOR BEST PERFORMANCE.. ............................................................ 3 
PREPARATION ................................................................................ 
5 
LOCATION OF CONTROLS 
............................................................... 
8 
WALL MOUNTING 
........................................................................ 10 
LOCATING THE HANDSET FROM THE BASE UNIT.. 
......................... 10 
ADJUSTING THE 
RINGER...

FOR BEST PERFORMANCE 
Ll Noise 
Calls are transmitted between the base unit and the handset using wireless radio waves. 
For maximum distance and noise free operation, the recommended base unit location is: 
Away from electrical appliances such 
as a fax, radio, or personal computer. 
In a HIGH location, with no 
obstructions or interference 
from electrical appliances. 
l Wireless telephones, except for the 900MHz telephone, can be used together. 
. X-P. out of range. an alarm tone sounds continuously...

FOR BEST PERFORMANCE 
Cl Battery Charge 
To power the handset, install the battery in the handset (see page 7) and place the handset 
on the charging unit for about 15 hours to charge before initial use. 
l The handset can also be placed with the dialing buttons 
facing upward. 
l The CHARGE indicator lights. 
l The battery cannot be overcharged. 
OR 
Note: 
l Clean the charge contacts with a soft cloth once a month, or the battery may not 
charge properly. 
l Once the handset battery is fully charged,...

PREPARATION 
II Charging Unit 
. . Connect as shown. 
Fasten the AC Adaptor 
cord to the cord holder 2. Close the cradle cover (included). 
To Power Outlet 
AC Adaptor 
THE WALL OUTLET POWER SOCKET SHOULD BE LOCATED 
NEAR THIS EQUIPMENT AND BE EASILY ACCESSIBLE. 
Vote: 
1 Spare Battery*: When the handset battery needs charging, replace it with the fully 
charged spare battery. This will eliminate waiting for the handset battery to fully 
recharge. 
1 USE ONLY Panasonic AC ADAPTOR KX-Al 1. The adaptor...

PREPARATION 
0 Base Unit 
1. Connect as shown. 
2. Raise the antenna. adaptor 1 
DIALING MODE Selector:  When in the SLT mode, setting is necessary. 
If your telephone line has touch tone 
service, set to “TONE?.” If it has rotary 
service, set to “PULSE.” 
CONNECTION MODE Selector: 2 
If connected to a Telephone Line Jack 
To Power Outlet 
or a PBX, except for Panasonic KX-T or AC Adaptor 
KX-TD series, set to “SLT.” (120VAC, 60HZ) - . 
m 
If this unit is connected to Panasonic 
KX-T or KX-TD series,...

PREPARATION 
iI Handset 
_. Install the battery 2. Close the handset cover 
(included) in the (included). 
direction of the arrow on 
the battery. 3. Set the POWER/RINGER 
switch to “ON.” 
Place the handset on the 
charging unit for about 15 
hours to charge the battery. 
uuuuu 
k-/J 
-ii 
D To install a handset clip 
You can hang the handset on your pocket by attaching the handset clip. 
1. Slide the cover in the direction of the 2. Insert the clip (included) in the direction 
arrow to remove it. of the...

LOCATION OF CONTROLS 
Cl Base Unit 
IN USE Indicator 
POWER Indicate Antenna 
CONNECTION MODE 
DIALING MODE Selector 
v ‘LOCATOR Button 
Cl Charging Unit 
CHARGE Indicator 
SPARE CHARGE _ 
Indicator Charge Contacts 
Cradle Cover 
Battery Charge Compartment 
for Spare Battery 
(under the cover)  

LOCATION OF CONTROLS 
.(Il Handset 
Antenna 
Flexible Keys (1 through 4) 
and 
Indicators: 
Used as a One-Touch Dialing, 
CO button, etc. Used to make or 
receive an intercom (Fl) i outside 
(F2 - F4) call in EMSS mode. 
AUTO Button: 
Used before dialing a speed 
dial number. Used to store 
programming in EMSS mode. 
TALK Button and 
Used to make or receive a call. 
The indicator flashes when the 
battery is low. 
pulse to tone during a call in 
SLT mode. 
POWER/RINGER Switch: 
Set to “ON.” If set to...

WALL MOUNTING 
The base unit can be mounted on a wall. 
1. Drill two holes spaced 2. Insert the tabs of the wall 
8.4 cm (3.3 inches) apart mounting plate (included) 
and install two screws. into the openings of the 
base unit, then push it in 
the direction of the arrow. 
8.4 cn; 
(3.3 inches) 3. Mount the base unit on the 
wall. 
LOCATING THE HANDSET FROM THE BASE UNIT 
This feature helps you find the handset if misplaced. You may also locate a person at the 
handset from the base unit by sounding beep...