Panasonic Micro - Foaming Cleansing Device Eh Xc10 Operating Instructions

11
Before use
• Read the following information on the recommended usage 
frequency for best skin care results.
Warm makeup removal Less than 3 minutes once per day
Brush cleansing Less than 1 minute once per day
Silicone brush cleansing
Less than 1 minute twice per week
Excessive use will have an adverse effect on the skin.  
Please adjust the number of times used and usage time 
depending on the appearance of your skin.
•  Please remove accessories (necklaces, earrings, etc.) before 
use as they may get...

12
English
 How to use
• Make sure the warming makeup removal plate is not cracked or 
dirty before use.
• 
The appliance will not operate when connected to the AC 
adaptor. The AC adaptor is used only for charging the appliance.
Warm makeup removal
The warming makeup removal plate loosens and easily removes 
makeup.
 1
1Press the warming makeup removal switch and 
select the desired temperature.
Warming makeup removal plate temperature options
Low (): approx. 43 °C (109 °F)
High (): approx. 48 °C (118...

13
English
Brush cleansing
Remove dead skin and dirt from pores with the gentle fi ne brush and 
microfoam.
If you are still wearing makeup, fi rst remove the makeup using the 
warm makeup removal mode or remove eye makeup with your hands.
 1
1Attach the soft brush by pressing 
it until it clicks into place.
2
2Open the facial cleanser compartment 
and add facial cleanser.
Add the recommended amount as 
indicated on your facial cleanser product 
(the amount you normally use).
Notes
• 
Use a foaming...

14


Do not press the bristles of the soft 
brush into your skin. Lightly apply the 
brush to your skin so that the bristles 
just touch the skin and then wash your 
face in a circular motion.
If you feel irritation even if you are not 
pressing the brush into the skin, stop 
using the brush.
• 
Do not use the brush around your eyes.
6
6After you have finished washing your face, press 
the facial cleanse switch to turn off the power.
• 
Make sure to wash the appliance after use.  
(See page 15.)
•...

15
Cleaning
1
1Rinse foam off the brush with water and then 
remove.
2
2Open the facial cleanser 
compartment cover, begin 
pouring water into the foam 
dispenser, and then press the 
facial cleanse switch to rinse.
• 
If a significant amount of facial 
cleanser remains, the power may 
turn off a few seconds after pressing 
the facial cleanse switch or may not 
operate smoothly. In such cases, use 
warm water to clean and remove the 
excess cleanser.
3
3Press the facial cleanse switch to turn off the...

16
Troubleshooting
ProblemPossible cause Action
The power does not turn on.
The appliance has not been charged.Charge the appliance.  
(See page 9.)
The AC adaptor is connected.Disconnect the AC adaptor before use.
The power turns off during use.
There is no power remaining in the battery.Charge the appliance.  
(See page 9.)
Appliance is clogged with facial cleanser.Use warm water to clean and remove 
the cleanser.
Too much facial cleanser or sticky facial 
cleanser or other inappropriate cleanser has...

17
ProblemPossible cause Action
Using the soft brush does not remove 
my makeup.
You did not remove makeup before using the 
soft brush, or you are using facial cleanser 
that does not remove makeup well.
If you are still wearing makeup, first 
remove the makeup using the warm 
makeup removal mode or remove eye 
makeup with your hands.
Using a facial cleanser designed to 
remove makeup is also more effective 
when using the soft brush.
The quality or quantity of foam is poor.
There is too much or too...

18
• Take care not to short circuit the positive and negative terminals 
of the removed battery, and insulate the terminals by applying 
tape to them.



Specifications
Power supply
See the name plate on the AC adaptor.
(Automatic voltage conversion)
Charging time Approx. 2 hours
This product is intended for household use only.
AC Adaptor: Conforms to ANSI/UL Std.1310, and 
Cert. to CAN/CSA C22.2 No.223.
Micro-Foaming Cleansing Device: 
 Conforms to UL Std. 1431, and Cert. to CAN/CSA 
E60335-2-23....

19
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio...

20
EH-XC10_AM.indb   202015/07/21   18:02:25