Panasonic Projector Pt L735ntu Operating Instructions

							ENGLISH-21
Getting started
Example of connecting to computer
NOTE:
BIt is better to shut down the computer before turning off the MAIN
POWER switch of the projector.
BDo not input the signal to the RGB2 IN/RGB1 OUT connector when the
RGB2 SELECT item in the OPTION menu is set to “OUTPUT”. (Refer
to page 45.)
162345 ON DIP
D-sub 9-pin
(male) Computer for
control useComputer
Monitor
Audio system
Refer to the accessory CD-ROM for details on the wireless network
that is used for controlling the projector with a personal computer
by means of the wireless card. (PT-L735NTU only) 
						

							22-ENGLISH
Operating range
If the remote control unit is held so that it is facing directly in front of the
remote control signal receptors on the front or rear of the projector, the
operating range is within approximately 7 m (23´) from the surfaces of the
receptors. Furthermore, the remote control unit can be operated from an
angle of ±30° to the left or right and ±15° above or below the receptors. #Open the cover.
AAA batteries
(two) $Insert the batteries so that the 
polarities are correct, and then close the
cover.
“
“ µ
“
µ
“
NOTE:
BIf there are any obstacles in between the remote control unit and the
receptors, the remote control unit may not operate correctly.
B
If strong light is allowed to shine onto the remote control signal receptor, correct projector
operation may not be possible. Place the projector as far away from light sources as possible.
BIf facing the remote control unit toward the screen to operate the projector,
the operating range of the remote control unit will be limited by the amount
of light reflection loss caused by the characteristics of the screen used.
NOTE:
BDo not drop the remote control unit.
BKeep the remote control unit away from liquids.
B
Remove the batteries if not using the remote control unit for long periods.
BDo not use rechargeable batteries.
Preparation for the remote control unit 
						

							ENGLISH-23
Basic Operation
Turning on the power
Before turning on the power
1, Ensure that all components
are connected properly.
2, 
Connect the accessory power cord.
3, Remove the lens cover.
Press the MAIN POWER switch to turn on the
power.
BThe power indicator on the projector will illuminate red.
Press the POWER button.
BThe power indicator on the projector will flash green. After a short
period, the indicator will illuminate green, and a picture will be
projected.
Turn on the power of all connected devices.
BStart the play function of a device such as a DVD player.
NOTE:
BA tinkling sound may be heard while the power indicator is turned off,
but this is not a sign of a malfunction.
#
$
%
Power indicator
AUTO SETUP
LASER
MENU VIDEO
PAGE
ENTER
R-CLICK
RGB POWER
$
(
)
*
&
'
'
#
Power cord
Lens cover 
						

							24-ENGLISH
Press the input select button to select the
input signal.
BA picture will be projected in accordance with the selected input signal.
Follow the procedure below when you set the projector up first, and when
you change the setup place.
Press the AUTO SETUP button to initiate
automatic positioning.
BThe tilt of the projector and the input
signal will be detected and keystone
distortion and the position of the
image will be corrected.
(Refer to page 27 for details.)
Adjusting the size
BTurn the zoom ring to adjust the size of the projected image.
Adjusting the focus
BTurn the focus ring to adjust the focus of the projected image.
AUTO SETUP
Input select
buttons PT-L735NTU
only
Changing
signals
VIDEO
S-VIDEO
RGB1
RGB2
&
'
)
* (
Adjusting the angle
BWhile pressing the adjuster buttons,
adjust the forward/back angle of tilt
of the projector. Adjust so that the
projector is as vertical to the screen
as possible.
RGB1RGB2
NETWORKSDCARD
RGBVIDEORGB 
						

							ENGLISH-25
Basic Operation
Turning off the power
Press the POWER button.
B“Power OFF” is displayed on the
screen.
Select “OK” using the I I
and H H
buttons and
then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected.
(The power indicator on the projector will illuminate orange.)
#
$
%
AUTO SETUP
LASER
MENU VIDEO
PAGE
ENTER
R-CLICK
RGB POWER
#
$
%
RGB input indicator Power indicator
Power OFF
OKCANCEL
Press the MAIN POWER switch to turn off the
power after the power indicator on the
projector illuminates red.
Direct power off function
You can turn off the MAIN POWER switch and move the projector immediately after use.
The cooling fan will operate by the internal power supply to cool down the lamp.
BWhen this function is used, it may take more time for the lamp to turn back on again
compared to when the lamp cools down while the MAIN POWER switch is ON.
BDo not put the projector in a bag while the cooling fan is operating. 
						

							26-ENGLISH
Power indicator
Power indicator status
Red
IlluminatedThe projector is in standby mode and image projection
is possible by pressing the POWER button.
A picture is being projected.
The lamp is cooling down after the power is turned
off. (The cooling fan is operating.)
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated orange. (After a short period, a picture
will be projected.) The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated red. (After a short period, a picture will be
projected.) FlashingWEB STANDBY in the NETWORK menu is set to
“ON”. The projector can be controlled with personal
computers by means of a wireless network. 
(The cooling fan is operating.) : PT-L735NTU only. Flashing
slowlyIlluminated
Illuminated
Flashing Green
OrangeProjector status
RGB INPUT indicator
RGB INPUT indicator status
Illuminated during
standby modeA signal is being input to either the RGB1 IN or
RGB2 IN connector.
Illuminated during
projectionA signal is being input to the connector selected
using the input select buttons.Projector status
NOTE:
BYou can also turn off the power by pressing the POWER button twice or
by holding down it for at least 0.5 seconds.
BWhen the projector is in standby mode (the power indicator on the
projector is illuminated red), the projector will still draw a maximum 7 W of
power, even when the cooling fan has stopped. 
(PT-L735NTU only)
BWhen the WEB STANDBY is set to “ON”, the cooling fan operates and
the power indicator on the projector flashes slowly in red and the
projector draw a maximum 30 W of power. (page 48)
BDo not turn off the power while the SD card is being accessed and “SD
CARD IN USE.” is displayed on the screen. 
						

							ENGLISH-27
Correcting keystone distortion and
automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone distortion and the
position of the image can then be corrected automatically in accordance with the input signal.
Projector control panelPress the AUTO SETUP button.
(When the projected image has caused keystone distortion)
BAutomatic positioning
will be carried out.
Screen
Projected
image
If you press the AUTO SETUP button, the items given in the table below will
be set automatically in addition to keystone distortion being corrected. The
setting details change according to the signal which is being input.
[
NOTE:
BIf the edges of the projected picture are indistinct, or if a dark picture is being
projected, the automatic setup processing may stop automatically before it is
complete. If this happens, project a different picture and then press the AUTO
SETUP button once more, or make the above adjustments manually.
BSet AUTO KEYSTONE in the OPTION menu to “OFF” to prevent any
deterioration of the picture as a result of keystone correction. (Refer to page 45.)
BKeystone distortion may not be corrected enough depending on the adjustment of
the zoom ring. In this case, adjust the KEYSTONE option. (Refer to page 41.)
Input signal Contents set up automatically
POSITION, DOT CLOCK, CLOCK PHASE
(If the dot clock frequency is 100 MHz or higher, the DOT
CLOCK  and CLOCK PHASE will not be set automatically.) RGB signalsPage
40,
41
LASER
MENU VIDEO
PAGE RGB POWER
AUTO SETUPAUTO SETUP
Useful functions 
						

							28-ENGLISH
Turning off the picture and sound
momentarily (SHUTTER)
The shutter function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in shutter mode than it does in
normal projection mode.
Still picture
BThe picture being projected will be paused.
BPress the FREEZE button again to cancel the
still picture. Press the SHUTTER button.
BThe picture and sound will be turned off.
BPress any button on either the projector or
remote control unit to return to normal operating
mode.
Press the FREEZE button.
Pausing a picture (FREEZE)
Computer
ENTERR-CLICK
FREEZE
SHUTTER
Projector
FUNC1STD
SHUTTER
Computer
ENTERR-CLICK
FREEZE
SHUTTER
Projector
FUNC1STD
FREEZE 
						

							ENGLISH-29
Useful functions
BThe picture will then
be enlarged to 1.5
times the normal size.
The remote control unit functions during D.ZOOM (digital zoom)
Use the F,G,IandHbuttons to move the enlarged area which you want to project.
Use the D.ZOOM +/- buttons to change the enlargement ratio.
Press the MENU button to return to the normal screen.
[
Enlarging the picture (D.ZOOM)
Adjusting the volume (VOLUME)
Press a D.ZOOM +/- button.
Press the VOLUME +/- button.
BPress the + button to raise the volume.
BPress the - button to lower the volume.
NOTE:
B
The enlargement ratio can be changed within the range of x1 to x4, by 30 steps.
BIf the type of signal being input changes while the digital zoom function
is being used, the digital zoom function will be cancelled.
NOTE:
BYou can also select “VOLUME” from the
AUDIO menu to adjust the volume.
LASER
MENU VIDEO
PAGE
ENTER
R-CLICK
FREEZE
SHUTTER
FUNC1STD RGB POWER
AUTO SETUP
Computer
FREEZE
SHUTTER
Projector
FUNC1STD 
						

							30-ENGLISH
Useful functions of the remote control unit
Laser beam pointer
The laser beam emitted from the remote control can be used as a pointer by
pointing forward to the screen.
While the LASER button is being pressed, the laser beam is being emitted
and the operating indicator illuminates.
Do not look into the laser emitter of the remote control unit or point the laser
beam towards other people, otherwise damage to eyes may occur.
Caution
BUse of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
BThis remote control unit cannot be repaired.
AUTO SETUP
LASER
MENU VIDEO
Computer
PAGE
ENTER
R-CLICK
FREEZE
SHUTTER
Projector
FUNC1STD RGB POWER
PUSH
Warning
BDO NOT STARE INTO THE LASER
BEAM OR AIM IT AT ANY PERSONS
EYE. LASER RADIATION CAN CAUSE
SERIOUS INJURY TO THE HUMAN EYE.
Laser Transmitter window