Panasonic Projector PT-RW620 User Manual

							Chapter 6 Maintenance — [SELF TEST] indications
ENGLISH - 181
Error/warning displayDetailsAction number
FF0 Radiator fan 2 error 5
FF1 Radiator fan 1 error 5
FH0 Phosphor wheel 1 error 5
FH1 5
FH2 Phosphor wheel 2 error 5
FH3 5
FJ0 Liquid cooling pump 1 error 5
FJ1 Liquid cooling pump 2 error 5
FL1 Light source 1 unit error 6
FL2 Light source 2 unit error 6
Note
 fThe self-diagnosis display and the details of the malfunction may be dif\
 ferent. fFor errors and warnings that are not described in the table, consult you\
r dealer
.
 rMeasure for error and warning
Action 
number Measure
1 The operating environment temperature is too high. Use the projector in \
an appropriate operating environment temperature
*1.
2 The operating environment temperature is too low. Use the projector in an appropriate operating environment temperature
*1.
3 The input supply voltage is low. Use electric wiring that can sufficiently withstand the power consumption of the projector.
4 Battery replacement is required. Consult your dealer.
5 If the display does not clear after switching the main power off and on, consult your dealer.
6 The light source has failed to turn on. If the light source does not lig\
ht up after turning the power off and on, consult your 
dealer.
*1 For details of operating environment temperature of the projector
, refer to “Operating environment temperature” (x   page   203).   
						

							182 - ENGLISH
Chapter 7 Appendix
This chapter describes specifications and after-sales service for the projector.  
						

							Chapter 7 Appendix — Technical information
ENGLISH - 183
Technical information
PJLink protocol
The network function of this projector supports the PJLink class 1, and the PJLink protocol can be used to perform 
projector setting and projector status query operations from a computer.
Control commands
The following table lists the PJLink protocol commands that can be used to control the projector .
 fx characters in tables are non-specific characters.
Command Control details Parameter/response 
string Remark
POWR Power supply control 0
Standby
1 Power on
POWR? Power supply status 
query 0
Standby
1 Power on
2 Preparing for switching off the projector
3 Warm-up
INPT Input selection 11
RGB1
12 RGB2
INPT? Input selection query 31DVI
- D
32 HDMI
33 DIGITAL LINK
34 SDI (Only for PT
-

RZ770, PT
-
 RZ660)
AVMT Shutter control 30Shutter function disabled (shutter: open)
AVMT? Shutter status query 31Shutter function enabled (shutter: closed)
ERST? Error status query xxxxxx 1st byte
Indicates fan errors, and returns 
0 - 2.
 f
0 = No error is 
detected
 f1 = W

arning
 f2 = Error
2nd byte
Indicates light source errors, and 
returns 0 - 2.
3rd byte Indicates temperature errors, and 
returns 0 - 2.
4th byte Returns 0.
5th byte Indicates filter errors, and returns 
0 - 2.
6th byte Indicates other errors, and returns 
0 - 2.
LAMP? Light source status 
query xxxxxxxxxxxx 1st number (1 - 5 digits): Light source 1 runtime
2nd number: 0 = Light source 1 of

f, 1 = Light source 1 on
3rd number (1 - 5 digits): Light source 2 runtime
4th number: 0 = Light source 2 off, 1 = Light source 2 on
INST? Input selection list query 11 12 31 32 33 34
Only for PT
-

RZ770, PT
-
 RZ660
11 12 31 32 33 Only for PT
-

RW730, PT
-
 RW620
NAME? Projector name query xxxxx Returns the name set in [PROJECTOR NAME] of [NETWORK 
SETUP].
INF1? Manufacturer name 
query Panasonic
Returns manufacturer name.
INF2? Model name query RZ770
RW730
RZ660
RW620Returns model name.
INF0? Other information 
queries xxxxx
Returns version number.
CLSS? Class information query 1Returns class for PJLink.   
						

							Chapter 7 Appendix — Technical information
184 - ENGLISH
PJLink security authentication
The password used for PJLink is the same as that of the password set for web control.
When using the projector without security authentication, do not set a p\
assword for web control.
 fFor specifications related to PJLink, visit the website of Japan Business Machine and Information System 
Industries Association.
URL

 http://pjlink.jbmia.or.jp/english/
Using Art-Net function
Since the network function of the projector supports the Art-Net function, you can control the projector settings 
with the DMX controller and application software using the Art-Net protocol.
Channel definition
The following table lists the channel definitions used for controlling the projector with the  Art-Net function.
Channel settings can be switched using the [NETWORK] menu  → [Art-Net CHANNEL SETTING] (x
  page   152).
The control details assigned to each channel are listed in the following\
 table.
 f Channel assignment for [USER] is in factory default setting. 

Assignment can be changed.
Channel Control details
[2] [USER] [1]
CHANNEL1 LIGHT OUTPUT LIGHT OUTPUT SHUTTER
CHANNEL2 INPUT SELECT INPUT SELECT INPUT SELECT
CHANNEL3 LENS POSITION LENS POSITIONLENS FUNCTION SELECT
CHANNEL4 LENS H SHIFT LENS H SHIFTLENS CONTROL
CHANNEL5 LENS V SHIFT LENS V SHIFT POWER
CHANNEL6 LENS FOCUS LENS FOCUSLIGHT OUTPUT
CHANNEL7 LENS ZOOM LENS ZOOMENABLE/DISABLE
CHANNEL8 POWERPOWER FADE-IN
CHANNEL9 GEOMETRY GEOMETRY FADE-OUT
CHANNEL10 CUSTOM MASKING
*1CUSTOM MASKING*1CUSTOM MASKING*1
CHANNEL11 ENABLE/DISABLE ENABLE/DISABLE GEOMETRY
CHANNEL12 NONENONE NONE
*1 For PT-RZ770, PT- RZ660. The setting for PT- RW730 or PT- RW620 is “NONE”.
Control details
 rLIGHT OUTPUT
This can be set in 256 steps between 100 % and 0 %.
Performance ParameterDefault value
100
 
% 0
0
… …
0
 
% 255   
						

							Chapter 7 Appendix — Technical information
ENGLISH - 185
 rINPUT SELECT (when [Art-Net CHANNEL  SETTING] is set to [1])
Performance ParameterDefault value
No operation 0
- 7
0
RGB1
8
- 15
RGB2 16
- 23
No operation 24
- 31
DVI
-
D 32
- 39
HDMI 40
- 47
DIGITAL LINK 48
- 55
SDI (Only for PT
-

RZ770, PT
-
 RZ660) 56
- 63
No operation 64
- 127
P IN P execution, USER1 128
- 135
P IN P execution, USER2 136
- 143
P IN P execution, USER3 144
- 151
No operation 152
- 255
 rINPUT SELECT (when [Art-Net CHANNEL  SETTING] is set to [2] or [USER])
Performance ParameterDefault value
No operation 0
- 7
0
RGB1
8
- 15
RGB2 16
- 23
DVI
-
D 24
- 31
HDMI 32
- 39
DIGITAL LINK 40
- 47
SDI (Only for PT
-

RZ770, PT
-
 RZ660) 48
- 55
No operation 56
- 119
P IN P OFF 120-127
P IN P execution, USER1 128
- 135
P IN P execution, USER2 136
- 143
P IN P execution, USER3 144
- 151
No operation 152
- 255
 rLENS POSITION
Performance ParameterDefault value
No operation 0
- 31
0
Move to the home position
*132-63
Move to the ET-
DLE030 lens standard position*2
No operation 64 - 255
*1 Operation when [NORMAL] is selected in [HOME POSITION] in the [HOME POSITION] screen
*2  Operation when [DLE030] is selected in [HOME POSITION] in the  [HOME POSITION] screen
 rLENS H SHIFT , LENS V SHIFT, LENS FOCUS, LENS ZOOM
Performance ParameterDefault value
Lens adjustment (
-) High speed
0 - 31
128
(
-) Low speed
32 - 63
(
-) Fine adjustment 64 - 95
Operation stop 96
- 159
Lens adjustment (+) Fine adjustment
160
- 191
(+) Low speed 192
- 223
(+) High speed 224
- 255   
						

							Chapter 7 Appendix — Technical information
186 - ENGLISH
 rLENS FUNCTION SELECT (when [Art-Net CHANNEL  SETTING] is set to [1])
Operate together with LENS CONTROL.
PerformanceParameterDefault value
No operation 0
- 15
0
LENS H SHIFT
16
- 31
LENS V SHIFT 32
- 47
LENS FOCUS 48
- 63
LENS ZOOM 64
- 79
Move to the home position
*180-95
Move to the ET-
DLE030 lens standard position*2
No operation 96 - 255
*1 Operation when [NORMAL] is selected in [HOME POSITION] in the [HOME POSITION] screen
*2  Operation when [DLE030] is selected in [HOME POSITION] in the  [HOME POSITION] screen
 rLENS CONTROL  (when [Art-Net CHANNEL SETTING] is set to [1])
Operate together with LENS FUNCTION SELECT.
Performance ParameterDefault value
Lens adjustment (
-) High speed
0 - 31
100
(
-) Low speed
32 - 63
(
-) Fine adjustment 64 - 95
Operation stop 96
- 127
Lens adjustment (+) Fine adjustment
128
- 159
(+) Low speed 160
- 191
(+) High speed 192
- 223
Execute command action 224
- 255
 rPOWER
Performance ParameterDefault value
Standby 0
- 63 128
No operation 64
- 191
Power on 192
- 255
 rSHUTTER
Performance ParameterDefault value
SHUTTER: Open 0
- 63 128
No operation 64
- 191
SHUTTER: Closed 192
- 255
 rFADE ‑ IN, FADE ‑ OUT (when [Art ‑ Net CHANNEL SETTING] is set to [1] or [USER])
Operate together with SHUTTER.
Performance ParameterDefault value
OFF 0
- 15
255
0.5s
16
- 31
1.0s 32
- 47
1.5s 48
- 63
2.0s 64
- 79
2.5s 80
- 95
3.0s 96
- 111
3.5s 112
- 127
4.0s 128
- 143
5.0s 144
- 159
7.0s 160
- 175
10.0s 176
- 191
No operation 192
- 255   
						

							Chapter 7 Appendix — Technical information
ENGLISH - 187
 rGEOMETR Y
Performance ParameterDefault value
OFF 0
- 15
255
KEYSTONE
16
- 31
CURVED CORRECTION 32
- 47
PC-1
*148-63
PC-2
*164-79
PC-3
*180-95
CORNER CORRECTION 96
- 111
No operation 112
- 255
*1 Only for PT- RZ770, PT- RZ660
 rCUSTOM MASKING (Only for PT‑RZ770, PT‑RZ660)
To use PC-1, PC-2, or PC-3, the optional Upgrade Kit (Model No.: ET- UK20) is required.
PerformanceParameterDefault value
OFF 0
- 31
255
PC-1
32
- 63
PC-2 64
- 95
PC-3 96
- 127
No operation 128
- 255
 rFREEZE
Performance ParameterDefault value
No operation 0
- 31
128
OFF
32
- 95
No operation 96
- 159
ON 160
- 223
No operation 224
- 255
 rCOLOR, TINT
Performance ParameterDefault value
No operation 0
- 31
0
Factory default setting
32
- 63
-31 64 - 65
… …
0 128
- 129
… …
+31 190
- 191
No operation 192
- 255
 rRASTER P ATTERN
Performance ParameterDefault value
No operation 0
- 15
0
OFF
16
- 31
WHITE 32
- 47
YELLOW 48
- 63
CYAN 64
- 79
GREEN 80
- 95
MAGENTA 96
- 111
RED 112
- 127
BLUE 128
- 143
BLACK 144
- 159
USER LOGO 160
- 175
No operation 176
- 255   
						

							Chapter 7 Appendix — Technical information
188 - ENGLISH
 rENABLE/DISABLE
Operation for all channels is not accepted when set to “Disable”.
Performance ParameterDefault value
Disable 0
- 127 0
Enable 128
- 255
Note
 fIf the projector is operated using the remote control or the control pan\
el, or by the control command while controlling the projector using the \
Art-Net function, the setting of the DMX controller or computer application may be dif ferent from the projector status. 
To reflect the controls 
of all channels to the projector, set “ENABLE/DISABLE” of channel 11 to “Disable” and then back to “Enable”.
 f T

o create/register the USER LOGO image, use “Logo Transfer Software” included in the supplied CD-ROM.
Control commands via LAN
When web control administrator rights password is set (Protect mode)
Connecting
1)  
Obtain the IP
  address and port number (Initial set value = 1024) of the projector a\
nd request a 
connection to the projector.
 f Y

ou can obtain both the IP address and the port number from the menu screen of the projector.
IP address Obtain from the [NETWORK] menu → [NETWORK STATUS].
Port number Obtain from the [NETWORK] menu → [NETWORK CONTROL]  → [COMMAND PORT].
2) Check the response from the projector.
Data section Blank Mode Blank Random number section Termination 
symbol
Command  example “NTCONTROL”
(ASCII string) ‘ ’
0x20 ‘1’
0x31 ‘ ’
0x20 “zzzzzzzz”
(ASCII code hex number) (CR)
0x0d
Data length 9
  bytes 1
  byte 1   byte 1   byte8
  bytes1
  byte
 fMode: 1 = Protect mode
 fExample: Response during protect mode (random number section is undefined value)
“NTCONTROL

 1 23181e1e” (CR)
3)
 
Generate a 32-byte hash value from the following data using MD5 algorith\
m.
 f “xxxxxx:yyyyy:zzzzzzzz”
xxxxxx Administrator rights user name for the web control (default user name is “admin1”)
yyyyy Password of above administrator rights user (default password is “panasonic”)
zzzzzzzz 8-byte random number obtained in Step  2)   
						

							Chapter 7 Appendix — Technical information
ENGLISH - 189
Command transmission method
Transmit using the following command formats.
 r Transmitted data
Header Data sectionTermination 
symbol
Command  example Hash value
“Connecting” ( x
 
page
 
188) ‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
Data length 32
 
bytes 1
  byte 1   byteUndefined length 1
  byte
 fExample: Transmission of power supply status acquisition command (hash value is calculated from default user 
name, password, and acquired random number)
“dbdd2dabd3d4d68c5dd970ec0c29fa6400QPW” (CR)
 r Received data
Header Data sectionTermination 
symbol
Command  example ‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
Data length 1
 
byte 1
  byte Undefined length 1
  byte
 fExample: The projector is powered on
“00001” (CR)
 r Error response
String DetailsTermination 
symbol
Message “ERR1” Undefined control command
(CR)
0x0d
“ERR2” Out of parameter range
“ERR3”
Busy state or no-acceptable period
“ERR4” Timeout or no-acceptable period
“ERR5” Wrong data length
“ERRA” Password mismatch
Data length 4
  bytes ―1
  byte
When web control administrator rights password is not set (Non-protect \
mode)
Connecting
1)  
Obtain the IP
  address and port number (Initial set value = 1024) of the projector a\
nd request a 
connection to the projector.
 f Y

ou can obtain both the IP address and the port number from the menu screen of the projector.
IP address Obtain from the [NETWORK] menu → [NETWORK STATUS].
Port number Obtain from the [NETWORK] menu → [NETWORK CONTROL]  → [COMMAND PORT].
2) Check the response from the projector.
Data sectionBlankModeTermination 
symbol
Command  example “NTCONTROL”
(ASCII string) ‘ ’
0x20 ‘0’
0x30 (CR)
0x0d
Data length 9
  bytes 1
  byte1
  byte1
  byte
 fMode: 0 = Non-protect mode
 fExample: Response during non-protect mode
“NTCONTROL

 0” (CR)   
						

							Chapter 7 Appendix — Technical information
190 - ENGLISH
Command transmission method
Transmit using the following command formats.
 r Transmitted data
Header Data sectionTermination 
symbol
Command  example ‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
Data length 1
 
byte 1
  byte Undefined length 1
  byte
 fExample: Transmission of power supply status acquisition command
“00QPW” (CR)
 r Received data
Header Data sectionTermination 
symbol
Command  example ‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
Data length 1
 
byte 1
  byte Undefined length 1
  byte
 fExample: The power of the projector is in standby status
“00000” (CR)
 r Error response
String DetailsTermination 
symbol
Message “ERR1” Undefined control command
(CR)
0x0d
“ERR2” Out of parameter range
“ERR3”
Busy state or no-acceptable period
“ERR4” Timeout or no-acceptable period
“ERR5” Wrong data length
“ERRA” Password mismatch
Data length 4
  bytes ―1
  byte