Panasonic Projector PT-RZ31K User Manual

							Chapter 5 Operations — Web control function
ENGLISH - 181
[Detail control] page
Click [Projector control] → [Detail control].
5 4
6 3 2
1
11 9 8
7
10
1 Control of the projector
The projector is controlled by clicking the buttons in the same 
way as the buttons on the remote control. After control, the on-
screen display of the projector at the right of the control page is 
updated.
2
 
[SUB MEMOR
 Y]
Switches the sub memory.
3
 
[SYSTEM DA
 YLIGHT VIEW]
Switches to system daylight view settings.
4
 
[FREEZE]
T

emporarily pauses the image.
5
 
[P
  IN P]
Switches the P IN P setting.
6
 
[LEFT/RIGHT SW
 AP]
Switches the flip horizontal settings. 7
 [W AVEFORM MONITOR]
Displays the waveform of the input signal.
8
 
[PROJECTION METHOD]
Switches the setting of the projection method.
9

 
[LENS]
Displays the [LENS] page.
10

 
[TEST P
 ATTERN]
Displays the test pattern.
Click the test pattern to display in the projected image from the 
patters displayed on the right side of the control page.
The display of the test pattern disappears if [Exit] is clicked.
11
 [GET OSD]
Updates the on-screen display of the projector at the right of the 
control page.
[LENS] page
Click [Projector control]  → [Detail control] → [LENS].
6 5
7 4 3 2 1
1 [HOME POSITION]
Moves the lens position to the home position or the 
ET
-

D75LE95 lens standard position.
2
 
[SHIFT]
Press 

asqw to adjust the shift.
The adjustment can be performed faster by holding down the 
button for approximately three seconds or longer.
3
 
[FOCUS]
Press 

qw to adjust the focus.
The adjustment can be performed faster by holding down the 
button for approximately six seconds or longer. 4
 [ZOOM]
Press 
qw to adjust the zoom.
5
 
[LENS MEMOR
 Y SAVE]
Saves the current lens position (shift, focus, and zoom). Click 
the number of the lens memory to save.
6
 
[LENS MEMOR
 Y LOAD]
Loads the lens position (shift, focus, and zoom). Click the 
number of the lens memory to load.
7
 
[Back]
Returns to the [Detail control] page.   
						

							Chapter 5 Operations — Web control function
182 - ENGLISH
[Network config] page
Click [Detailed set up] → [Network config].
 fClick [Network config] to display the  [CAUTION!]

 screen.
 fClick the [Next] button to display the current settings.
 fClick the [Change] button to display the setting change screen.
1
2
3
4
5
6
7
8
1 [PROJECT OR NAME]
Enter the name of the projector. Enter the host name if it is 
required when using a DHCP server etc.
2
 
[DHCP
  ON], [DHCP OFF]
To enable the DHCP client function, set to [DHCP ON].
3
 
[IP
  ADDRESS]
Enter the IP address when not using a DHCP server.
4
 
[SUBNET MASK]
Enter the subnet mask when not using a DHCP

 server.
5
 
[DEF
 AULT GATEWAY]
Enter the default gateway address when not using a DHCP 
server. 6
 [DNS1]
Enter the DNS1 server address.
Permissible characters for the entry of DNS1 server address 
(primary):
Numbers (0 - 9), period (.)
(Example: 192.168.0.253)
7
 
[DNS2]
Enter the DNS2 server address.
A

vailable characters for the entry of DNS2 server address 
(secondary):
Numbers (0 - 9), period (.)
(Example: 192.168.0.254)
8
 
[Back], [Next]
Click the [Back] button to return to the original screen. Click the 
[Next] button to display the setting confirmation screen. Click 
the [Submit] button to update the setting.
Note
 fWhen you use the “Forward” and “Back” functions of your browser , a warning message “Page has Expired” may appear. In that case, click 
[Network config] again since the following operation will not be guaranteed.
 f Changing LAN settings while connected to the LAN may cause the connection to cut out.   
						

							Chapter 5 Operations — Web control function
ENGLISH - 183
[Adjust clock] page
Click [Detailed set up] → [Adjust clock].
1
2
3
4
5
6
7
1 [Time Zone]
Select the time zone.
2
 
[Set time zone]
Updates the time zone setting.
3

 
[NTP
  SYNCHRONIZATION]
Set to [ON] when setting the date and time automatically.
4
 
[NTP
  SERVER NAME]
Enter the IP address or server name of the NTP server when 
you set to adjust the date and time manually.
(To enter the server name, the DNS server needs to be set up.) 5
 [Date]
Enter the date to be changed.
6
 
[T
 ime]
Enter the time to be changed.
7
 
[Submit]
Updates the date and time settings.
Note
 fThe replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Consult 
your dealer
.
[Ping test] page
Check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up]  → [Ping test].
1
2 3
4
1 [Input IP  address]
Enter the IP address of the server to be tested.
2
 
[Submit]
Executes the connection test. 3

 Example of display when the connection has succeeded
4  
Example of display when the connection has failed   
						

							Chapter 5 Operations — Web control function
184 - ENGLISH
[E-mail set up] page
Send an E-mail to preset E-mail addresses (up to two addresses) when a problem has occurred.
Click [Detailed set up] → [E-mail set up].
1
2
3
4
5
6
1 [ENABLE]
Select [ENABLE] to use the E-mail function.
2
 
[SMTP
  SERVER NAME]
Enter the IP address or the server name of the E-mail server 
(SMTP). To enter the server name, the DNS server needs to be 
set up.
3
 
[MAIL
  FROM]
Enter the E-mail address of the projector. (Up to 63 characters 
in single byte)
4
 
[MEMO]
Enter information such as the location of the projector that 
notifies the sender of the E-mail. (Up to 63 characters in single 
byte) 5

 [MINIMUM TIME]
Change the minimum interval for the temperature warning 
E-mail. 
The default value is 60 minutes. In this case, another 
E-mail will not be sent for 60 minutes after sending the 
temperature warning E-mail even if it reaches the warning 
temperature.
6
 
[INT
 AKE AIR TEMPERATURE]
Change the temperature setting for the temperature warning 
mail. A temperature warning E-mail is sent when the 
temperature exceeds this value.
8
7
9
8
7
7 [E-MAIL  ADDRESS 1], [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 
2] blank when two E-mail addresses are not to be used. 8
 Settings of the conditions to send E-mail
Select the conditions to send E-mail.
[MAIL
 CONTENTS]: 
Select either [NORMAL] or [SIMPLE].
[ERROR]: 
Send an E-mail when an error occurred in the self-diagnosis.
[INTAKE AIR TEMPERATURE]: 
Send an E-mail when the intake air temperature has reached 
the value set at the above field.
[PERIODIC REPORT]: 
Place a check mark on this to send an E-mail periodically.
An E-mail will be sent on the day and time with the check mark.
9
 
[Submit]
Updates the settings and sends the details by E-mail.   
						

							Chapter 5 Operations — Web control function
ENGLISH - 185
[Authentication set up] page
Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail.
Click [Detailed set up] → [Authentication set up].
1
2
3
4
5
6
7
8
1 [Auth]
Select the authentication method specified by your Internet 
service provider
.
2
 
[SMTP
  Auth]
Set when the SMTP authentication is selected.
3
 
[POP
  server name]
Enter the POP server name.
Allowed characters:
Alphanumerics (A - Z, a - z, 0 - 9)
Minus sign (-) and period (.)
4
 
[User name]
Enter the user name for the POP

 server or the SMTP server. 5
 [Password]
Enter the password for the POP
 server or the SMTP server.
6
 
[SMTP
  server port]
Enter the port number of the SMTP server.
(Normally 25)
7
 
[POP
  server port]
Enter the port number of the POP server.
(Normally 110)
8
 
[Submit]
Update the settings.   
						

							Chapter 5 Operations — Web control function
186 - ENGLISH
Contents of E-mail sent
Example of the E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been establis\
hed.
=== P anas onic  pr ojec t or  r epor t ( CO NF I G URE )  ===
P r ojec t or  T y pe  :  RZ 31K
S er ial No  :  123456789012
-----  E-mail set up dat a -----
T EMPERAT URE WARNING  SET UP 
MINIMUM TIME  at  [  60]  m inut es  int er v al 
I NT A K E  A I R T E M P E RA T URE   O v er  [  46 degC /  114 degF  ]  
E RRO R  [ OFF ] 
INT AKE AIR T EMPERAT URE  [ O F F  ]
P E RI O DI C RE P O RT  
S unday   [  O N  ]   M onday   [  O N  ]   T ues day   [  O N  ]   Wednes day   [  O N  ]  
T hur s day   [  O N  ]   F r iday   [  O N  ]   S at ur day   [  O N  ]  
00: 00  [  O N  ]     01: 00  [  O N  ]     02: 00  [  O N  ]     03: 00  [  O N  ]  
04: 00  [  O N  ]     05: 00  [  O N  ]     06: 00  [  O N  ]     07: 00  [  O N  ]  
08: 00  [  O N  ]     09: 00  [  O N  ]     10: 00  [  O N  ]     11: 00  [  O N  ]  
12: 00  [  O N  ]     13: 00  [  O N  ]     14: 00  [  O N  ]     15: 00  [  O N  ]  
16: 00  [  O N  ]     17: 00  [  O N  ]     18: 00  [  O N  ]     19: 00  [  O N  ]  
20: 00  [  O N  ]     21: 00  [  O N  ]     22: 00  [  O N  ]     23: 00  [  O N  ]  
-----  ERRO R I NF O RMAT I O N  -----
E r r or  c ode
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
I nt ak e air  t em per at ur e  :  25 degC /   77 degF
O pt ic s  m odule t em per at ur e  :  28 degC /   82 degF
E x haus t  air  t em per at ur e  :  28 degC /   82 degF
Light 1- B  t em per at ur e  :  28 degC /   82 degF
Light 1- S  t em per at ur e  :  28 degC /   82 degF
Light 2- B  t em per at ur e  :  29 degC /   84 degF
Light 2- S  t em per at ur e  :  28 degC /   82 degF
P RO JE CT O R RUNT I M E      7 H
P O WE R O N  132 t im es
LI G HT 1 RUNT I M E      7 H
LI G HT 1 O N  174 t im es
LI G HT 2 RUNT I M E      7 H
LI G HT 2 O N  177 t im es
-------- Current  st at us ---------
MAIN VERSIO N  1. 00 
SUB VERSIO N  1. 00 
LIGHT STATUS
LI G HT 1- B =O N LI G HT 1- S =O N
LI G HT 2- B =O N LI G HT 2- S =O N
I NP UT   S DI 1
SIG NAL NAME   ---
S I G NA L F RE Q UE NCY   ---kHz /  ---Hz 
REMO T E2 ST AT US  DISABLE 
----- Wired Net work conf igurat ion -----
DHCP  Client   O F F  
I P  addr es s   192. 168. 0. 8
M A C addr es s   12: 34: 56: 78: 90: 12
M on J an 01 12: 34: 56 20X X
----- Memo -----   
						

							Chapter 5 Operations — Web control function
ENGLISH - 187
Example of the E-mail sent for an error
The following E-mail is sent when an error has occurred.
=== P anas onic  pr ojec t or  r epor t ( E RRO R)  ===
P r ojec t or  T y pe  :  RZ 31K
S er ial No  :  123456789012
-----  ERRO R I NF O RMAT I O N  -----
U21  I nt ak e air  t em p.  er r or
E r r or  c ode
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
I nt ak e air  t em per at ur e  :  25 degC /   77 degF
O pt ic s  m odule t em per at ur e  :  28 degC /   82 degF
E x haus t  air  t em per at ur e  :  28 degC /   82 degF
Light 1- B  t em per at ur e  :  28 degC /   82 degF
Light 1- S  t em per at ur e  :  28 degC /   82 degF
Light 2- B  t em per at ur e  :  29 degC /   84 degF
Light 2- S  t em per at ur e  :  28 degC /   82 degF
P RO JE CT O R RUNT I M E      7 H
P O WE R O N  132 t im es
LI G HT 1 RUNT I M E      7 H
LI G HT 1 O N  174 t im es
LI G HT 2 RUNT I M E      7 H
LI G HT 2 O N  177 t im es
-------- Current  st at us ---------
MAIN VERSIO N  1. 00 
SUB VERSIO N  1. 00 
LIGHT STATUS
LIGHT1-B=OFF LIGHT1-S=OFF
LIGHT2-B=OFF LIGHT2-S=OFF
I NP UT   S DI 1
SIG NAL NAME  ---
S I G NA L F RE Q UE NCY   ---kHz /  ---Hz
REMO T E2 ST AT US  DISABLE  
----- Wired Net work conf igurat ion -----
DHCP  Client   OFF 
I P  addr es s   192. 168. 0. 8
M A C addr es s   12: 34: 56: 78: 90: 12
M on J an 01 12: 34: 56 20X X
----- Memo -----   
						

							Chapter 5 Operations — Web control function
188 - ENGLISH
[Change password] page
Click [Change password].
1
2
3
1 [Administrator]
Used to change the setting of the [Administrator].
2
 
[User]
Used to change the setting of the [User]. 3

 [Next]
Used to change the setting of the password.
[Administrator] account
1
3
2
4
1 [Account]
Displays the account to change.
2
 
[Current]
[User name]: 
Enter the user name before the change.
[Password]: 
Enter the current password. 3

 [New]
[User name]: 
Enter the desired new user name. (Up to 16 characters in single 
byte)
[Password]: 
Enter the desired new password. (Up to 16 characters in single 
byte)
[Password(Retype)]: 
Enter the desired new password again.
4
 
[OK]
Determines the change of password.   
						

							Chapter 5 Operations — Web control function
ENGLISH - 189
[User] account
1
2
3
1 [Account]
Displays the account to change.
2
 
[New]
[User name]: 
Enter the desired new user name. (Up to 16 characters in single 
byte)
[Password]: 
Enter the desired new password. (Up to 16 characters in single 
byte)
[Password(Retype)]: 
Enter the desired new password again. 3

 [OK]
Determines the change of password.
[Change password] (For user rights)
Only the change of password is enabled under the user rights.
1
2
4 3
1 [Old Password]
Enter the current password.
2
 
[New Password]
Enter the desired new password. (Up to 16 characters in single 
byte) 3

 [Retype]
Enter the desired new password again.
4
 
[OK]
Determines the change of password.
Note
 fTo change the account of the [Administrator], entry of [User name] and [Password] in [Current] is required.
[Crestron Connected(TM)] page
The projector can be monitored/controlled with Crestron ConnectedTM.
It is necessary to access with the administrator rights to start the ope\
ration screen of Crestron Connected
TM from 
the web control screen. (The [Crestron Connected(TM)] button is not displayed in the web control screen with the 
user rights.)
The operation page of Crestron Connected
TM is displayed by clicking [Crestron Connected(TM)].
It is not displayed if Adobe Flash Player is not installed on your computer, or the browser you use does not 
support Flash. In such a case, click [Back] in the operation page to go back to the previous page.   
						

							Chapter 5 Operations — Web control function
190 - ENGLISH
Operation page
1
2
34
5
6
7
1 [Tools], [Info], [Help]Tabs for selecting the setting, information, or help page of the 
projector.
2
 
[POWER]
T

urns on/off the power.
3
 
[SHUTTER]
Switches the status of the shutter

. ([CLOSE]: Shutter function 
enabled; [OPEN]: Shutter function disabled) 4
 [Input Select]
Controls input selection.
Not available when the power of the projector is turned of
f.
5
 
Menu screen control buttons
Navigates the menu screen.
6

 
Freeze/image quality adjustment
Controls items related to freeze/image quality

.
7
 
[Back]
Returns to the previous page.
[Tools] page
Click [Tools] in the operation page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the 
controller to be connected with the projector
.
2
 
[User Password]
Set the user rights password for the operation page of Crestron 
Connected
TM.
3
 
[Admin Password]
Set the administrator rights password for the operation page of 
Crestron Connected
TM. 4  
Network status
Displays the settings of wired LAN.
[DHCP]
Displays the current setting.
[Ip 

Address]
Displays the current setting.
[Subnet Mask]
Displays the current setting.
[Default Gateway]
Displays the current setting.
[DNS Server]
Displays the current setting.
5
 
[Exit]
Returns to the operation page.