Panasonic Projector PT-SW280A User Manual

							Chapter 5 Operation of Function —
 Web control function
ENGLISH - 91
Web control function
The wireless module (Model No.: ET-WML100E) of the optional accessories is required if you want to use the 
network function through the wireless LAN.
The projector has a network function, and the following operations are a\
vailable from the computer by using the 
web control.
 
f Setting and adjustment of the projector
 
f Display of the projector status
 
f Transmission settings of E-mail messages
Note
 
f If you use the E-mail function, you need to communicate with the E-mail server. First, please make sure that you can use the E-mail.
Computer that can be used
In order to use the Web control function, a Web browser is required. Confirm that the Web browser can be used 
beforehand.
OSCompatible web browser
Windows Internet Explorer 11.0
 Microsoft Edge
Mac OSSafari 6.0/7.0/8.0/9.0
Note
 
f Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.
Accessing from the web browser
1) Start up the web browser on the computer.
2) Enter the IP address set on the projector into the URL entry field of the web browser.
3) Enter the user name and the password.
 
f The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the 
password is panasonic (lower case).   
						

							Chapter 5 Operation of Function —
 Web control function
92 - ENGLISH
4) Click [OK].
 
f The [Projector status] page is displayed.
Note
 
f Do not perform setting or control simultaneously by starting up multiple\
 web browsers. Do not set or control the projector from multiple 
computers.
 
f Change the password first. (
x page 98)
 
f Access will be locked for few minutes when an incorrect password is ente\
red three times consecutively.
 
f Some items on the projector setting page use the Javascript function of \
the web browser. The projector may not be able to be controlled 
properly if it is set with a browser that does not have this function en\
abled.
 
f If the screen for the web control is not displayed, consult your network\
 administrator.
 
f While updating the screen for the web control, the screen may become whi\
te for a moment, but it is not a malfunction.
 
f About computer screen illustrations
 
The subsequent web control screens show examples for PT-SX320A. Screen content may differ from that for the projector model you 
are using. In addition, the screen size and the display may be differ from this manual depending on the OS, WEB browser or the type of 
computer you are using.
Available functions per account
With the administrator rights, all functions can be used. With the user \
rights, available functions are restricted. 
Select an account according to the purpose of use.
l :  The operation can be performed.
― :  
 The operation cannot be performed.
Item FunctionAdministrator rights User rightsPage
[Status]
[Projector status]ll93
Error information page
ll94
[Network status]
ll95
[Projector control][Basic control]ll95
[Detail control]
ll95
[Detailed set up]
[Network config]l―96
[Ping test]
l―97
[ECO management set up] 
l―97
[Change password]
User name of [Administrator]l―98
User name of [User]
l―99
Password of [Administrator]
l―98
Password of [User]
ll99
[Download]Download Presenter Light ll88   
						

							Chapter 5 Operation of Function —
 Web control function
ENGLISH - 93
Descriptions of items
1 Page tabPages are switched by clicking this item.
2 [Status]The status of the projector is displayed by clicking this item.
3 [Projector control]The [Projector control] page is displayed by clicking this item.
4 [Detailed set up]The [Detailed set up] page is displayed by clicking this item.
5 [Change password]The [Change password] page is displayed by clicking this item.
6 [Download]The download page of Presenter Light software is displayed by 
clicking this item. (
x page 88)
[Projector status] page
Click [Status] 
→ [Projector status].
Display the status of the projector for the following items.
1
2
3
4
5
6 7
8
9
11
13 12 10
A
ON    OFF
1 [PROJECTOR TYPE]Displays the type of the projector.
2 [MAIN VERSION]Displays the firmware version of the projector.
3 [POWER]Displays the status of the power.
4 [PICTURE MODE]Displays the setting status of [PICTURE MODE].
5 [INPUT]Displays the status of the selected input.
6 [LAMP RUNTIME]Displays the runtime of the lamps (converted value).
7 [SERIAL NUMBER]Displays the serial number of the projector.
8 [AV MUTE]Displays the status of the AV mute.
9 [VOLUME]Displays the volume status.
10 [INTAKE AIR TEMPERATURE]Displays the status of the air intake temperature of the projector.
11  [EXHAUST AIR TEMPERATURE]Displays the status of the exhaust air temperature of the 
projector.
12 [SELF TEST]Displays the self-diagnosis information.
13 [PROJECTOR RUNTIME]
Displays the runtime of the projector.   
						

							Chapter 5 Operation of Function —
 Web control function
94 - ENGLISH
Error information page
When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, 
click it to display the error/warning details.
 
f The projector may go into the standby status to protect the projector de\
pending on the contents of the error.
1 Self-diagnosis result displayDisplays the item check results.[OK]: Indicates that operation is normal.[FAILED]: Indicates that there is a problem.[WARNING]: Indicates that there is a warning.
 r[FAILED] items displayed when a problem occurs
ItemDescription
[FAN]
Trouble has occurred in the fan or its drive circuit. Consult your dealer\
.
[FAN(B)] Trouble has occurred in the B panel cooling fan.
[FAN(R_G)] Trouble has occurred in the R/G panel cooling fan.
[FAN(LAMP)] Trouble has occurred in the lamp cooling fan.
[FAN(POWER)] Trouble has occurred in the power cooling fan.
[FAN(EXHAUST)] Trouble has occurred in the exhaust fan.
[INTAKE AIR TEMPERATURE] The air intake temperature is too high. The projector may be used in an operating 
environment where the temperature is high, such as near a heating applia\
nce.
[EXHAUST AIR TEMPERATURE] The exhaust air temperature is high. The air exhaust port may be blocked.
[LAMP REMAIN TIME] The lamp runtime has exceeded the prescribed cumulative time, and it is \
now time to replace
the lamp.
[LAMP STATUS] The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
[INTAKE AIR TEMP.SENSOR] Trouble has occurred in the sensor used to detect intake air temperature.\
 Consult your 
dealer.
[EXHAUST AIR TEMP.SENSOR] Trouble has occurred in the sensor used to detect exhaust air temperature\
. Consult your 
dealer.
[AIR FILTER] There is too much dust accumulated in the air filter. After the projector is switched off, and 
clean the air filter. (
x page 102)
[COVER OPEN] Cover open error.   
						

							Chapter 5 Operation of Function —
 Web control function
ENGLISH - 95
[Network status] page
Click [Status] 
→ [Network status].
The current network setting status is displayed.
1
1 [WIRELESS LAN]Displays the configuration details of wireless LAN when the wireless module is attached.
[Basic control] page
Click [Projector control]  → [Basic control].
1
2
3
4
5
6
1 [INPUT]Switches the input signal.
2 [VOLUME]Adjusts the volume.
3 [PICTURE MODE]Switches the picture mode.
4 [AV MUTE]Switches on/off the AV mute.
5 [POWER]Turns off the power.
6 [CLOSED CAPTION]Switches the closed caption setting.
[Detail control] page
Click [Projector control] 
→ [Detail control].
1
2
1 [POSITION]
Operates field angle-related settings.
2 [PICTURE]
Operates picture quality settings.    
						

							Chapter 5 Operation of Function —
 Web control function
96 - ENGLISH
[Network config] page
Click [Detailed set up] 
→ [Network config].
1) Click [Network config].
 
f The [CAUTION!] screen is displayed.
1
2
2) Select the item which you want to change the setting, then click [Next].\
 
f The current setting is displayed.
3) Click [Change] button.
 
f When the wireless module is attached, the setting screen is displayed.
1
2
3
4
5
1 [SSID]Sets the SSID for use.
2 [CHANNEL]Selects the channel for use.
3 [ENCRYPTION]Selects [WPA2-PSK(AES)] when performing encrypted 
communications.
4 [KEY]Sets the key to be used when performing encrypted 
communications.
8 to 15 alphanumerics can be input. 
5 [Back], [NEXT]Click the [Back] button to return to the original screen.
Note
 
f The setting values of the [Network config] page will return to the factory default when the [INITIALIZE] of the [NETWORK] menu is executed. 
 
( x  page 82)   
						

							Chapter 5 Operation of Function —
 Web control function
ENGLISH - 97
[Ping test] page
Check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up] 
→ [Ping test].
1
23
4
1 [Input IP address]Enter the IP address of the server to be tested.
2 [Submit]Executes the connection test.
3 Example of display when the connection has succeeded
4 Example of display when the connection has failed
[ECO management set up] page
Settings related to the ECO management function of the projector can be \
made.
Click [Detailed set up] 
→ [ECO management set up].
1
2
3
4
5
6
8 7
1 [LAMP POWER]Selects the [LAMP POWER] setting.
2 [AUTO POWER SAVE]Sets to [ON] when setting [AMBIENT LIGHT DETECTION], 
[SIGNAL DETECTION] and [AV MUTE DETECTION].
3 [AMBIENT LIGHT DETECTION]Selects enable ([ON])/disable ([OFF]) of the environmental 
luminance interlock function.
4 [SIGNAL DETECTION]Selects enable ([ON])/disable ([OFF]) of the no signal interlock 
function.
5 [AV MUTE DETECTION]Selects to enable ([ON])/disable ([OFF]) of the AV mute 
detection function.
6 [POWER MANAGEMENT]Selects the power consumption mode.
7 [TIMER]Selects the time that the lamp is turned off when the POWER 
MANAGEMENT function is using.
8 [Submit]Updates the settings.
Note
 
f For details of each setting item, refer to the [PROJECTOR SETUP] menu 
→ [ECO MANAGEMENT] (
x page 72) on the projector.   
						

							Chapter 5 Operation of Function —
 Web control function
98 - ENGLISH
[Change password] page
Click [Change password].
1
2
3
1 [Administrator]Used to change the setting of the [Administrator].
2 [User]Used to change the setting of the [User].
3 [Next]Used to display the screen for changing the password.
[Administrator] account
1
2
3
4
1 [Account]Displays the account to change.
2 [Current][User name]:Enter the user name before the change.[Password]:Enter the current password.
3 [New][User name]:Enter the desired new user name. (Up to 16 characters in single 
byte)
[Password]:Enter the desired new password. (Up to 16 characters in single 
byte)
[Password(Retype)]:Enter the desired new password again.
4 [OK]Determines the change of password.   
						

							Chapter 5 Operation of Function —
 Web control function
ENGLISH - 99
 [User] account
1
2
3
1 [Account]Displays the account to change.
2 [New][User name]:Enter the desired new user name. (Up to 16 characters in single 
byte)
[Password]:Enter the desired new password. (Up to 16 characters in single 
byte)
[Password(Retype)]:Enter the desired new password again.
3 [OK]Determines the change of password.
[Change password] (For user rights)
The change of password is enabled only under the user rights.
1
2
3
4
1 [Old Password]Enter the current password.
2 [New Password]Enter the desired new password. (Up to 16 characters in single 
byte)
3 [Retype]Enter the desired new password again.
4 [OK]Determines the change of password.
Note
 
f To change the account of the administrator, you must enter the [User name] and the [Password] in [Current].   
						

							100 - ENGLISH
Chapter 6 Maintenance
This chapter describes methods of inspection when there are problems, ma\
intenance, and replacement of the 
units.