Panasonic Projector PT-SX320A User Manual

							Chapter 4 Settings —
 [PROJECTOR SETUP] menu
ENGLISH - 71
Note
 
f To specify an ID number for individual control, the ID number of a remote\
 control must match the ID number of the projector.
 
f When the ID number is set to [ALL], the projector will operate regardless of the ID number specified during remote control or computer 
control.  
If multiple projectors are set up side by side with ID set to [ALL], the\
y cannot be controlled separately from the projectors with other ID 
numbers.
 
f Refer to 
“
Setting the ID number of the remote control ”
 (
Æ page 46) for how to set the ID number on the remote control.
[INITIAL START UP]
Set the method of start up when the power cord plugged into the AC outlet.
1) Press as to select [INITIAL START UP].
2) Press qw to switch the item.
 
f The items will switch each time you press the button.
[LAST MEMORY]Starts in the condition that before disconnected the power cord or turn \
off the breaker. 
[STANDBY]Starts up in the standby mode.
[ON]Starts the projection immediately.
[PROJECTION METHOD]
Set the projection method in accordance with the installation status of \
the projector.
Change the projection method if the screen display is upside down or inv\
erted.
1) Press as to select [PROJECTION METHOD].
2) Press qw to switch the projection method.
 
f The items will switch each time you press the button.
[AUTO]The projector
’
s posture can be detected automatically by the built-in angle sensor, then switch to 
[FRONT/DESK] or [FRONT/CEILING]. When projecting in front of the screen,\
 please set to [AUTO].
[FRONT/DESK]When installing the projector on the desk, etc., in front of the screen.\
[FRONT/CEILING]When installing the projector in front of the screen with the Ceiling Mount Bracket (optional).
[REAR/DESK]When installing the projector on the desk, etc., behind the screen (with a translucent screen).
[REAR/CEILING]When installing the projector behind the screen (with a translucent screen) with the Ceiling Mount 
Bracket (optional).
Note
 
f When set to [AUTO], front projection or rear projection cannot be detected. When project\
ing from rear, please set the [PROJECTION 
METHOD] to [REAR/DESK] or [REAR/CEILING].
 
f As for the range of installation posture detected by the projector
’
s built-in angle sensor, please refer to  “
Angle sensor ”
. (
x page 26)
[LAMP POWER]
Switch the brightness of the lamp according to the operating environment\
 of the projector or the purpose.
1) Press as to select [LAMP POWER]. 
2) Press qw to switch the item.
 
f The items will switch each time you press the button.
[NORMAL]Select when high luminance is required.
[ECO]Select when high luminance is not required.
Note
 
f Set it to [ECO] rather than [NORMAL] when you want to reduce power consu\
mption, extend the life of lamp and reduce operation noise. 
f The [LAMP POWER] changes to [ECO] forcibly to protect the projector when the oper\
ating environment temperature becomes 35 
°
C (95  °
F)
or higher (30  °
C (86  °
F) or higher when used at high altitude). And, even if the [PROJECTOR SETUP] menu  
→ [LAMP POWER] is set to 
[NORMAL], the [LAMP POWER] changes to [ECO] automatically.
[LAMP RUNTIME]
Displays the runtime of the lamps
Be sure to reset the [LAMP RUNTIME] after replacing the lamp unit, refer to  “
Lamp unit replacement time ”
 
( x  page 104)   
						

							Chapter 4 Settings —
 [PROJECTOR SETUP] menu
72 - ENGLISH
[ECO MANAGEMENT]
This function optimizes lamp power according to the operating status to \
reduce power consumption.
Setting [AUTO POWER SAVE]
Set whether or not to enable the [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE 
DETECTION]  functions.
1) Press as to select [ECO MANAGEMENT].
2) Press the  button.
 
f The [ECO MANAGEMENT] screen is displayed.
3) Press as to select  [AUTO POWER SAVE].
4) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Disables the energy conservation setting.
[ON]Enables the energy conservation setting.
5) Press as to select [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] or [AV MUTE DETECTION].
[AMBIENT LIGHT DETECTION]Adjusts the power of the lamp according to the brightness of the install\
ation location.
[SIGNAL DETECTION]Lowers the power of the lamp when there is no signal.
[AV MUTE DETECTION]Lowers the power of the lamp when the [AV MUTE] is [ON].
6) Press qw to switch the item. 
f The items will switch each time you press the button.
[OFF]Disables the setting.
[ON]Enables the setting.
Note
 
f Lamp power cannot be reduced automatically in the following cases:
 
- When the lamp lighting is just completed or the setting of [LAMP POWER] is just completed, etc..
 
f When [AUTO POWER SAVE] is set to [OFF], settings of [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE 
DETECTION] are unavailable.
 
f When [LAMP POWER] is set to [ECO], settings of [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE DETECTION] 
are unavailable.
 
f When objects, etc. are placed around the luminance sensor on the top of \
the projector, [AMBIENT LIGHT DETECTION] may not function 
properly.
Setting [POWER MANAGEMENT]
Set the operation as following if there is no signal input.
1) Press as to select [ECO MANAGEMENT].
2) Press the  button.
 
f The [ECO MANAGEMENT] screen is displayed.
3) Press as to select [POWER MANAGEMENT].
4) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Power management function is off.
[READY]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp turns off 
and cools down when reaching the set time, meanwhile the projector is in\
 the power management 
mode. The projection lamp will be turned on if the input signal is reconnected or any button is pressed.
[SHUT DOWN]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp is turned 
off and cooled down when reached the set time, then the projector enter in\
to standby status.   
						

							Chapter 4 Settings —
 [PROJECTOR SETUP] menu
ENGLISH - 73
Setting [TIMER]
The timer can be set to 5-120 minutes. The increment is 5 minutes.
1) Press as to select [TIMER].
2) Press qw to set the timer.
 
f The time will switch each time you press the button.
Setting [STANDBY MODE]
Set the power consumption during standby.
1) Press as to select [ECO MANAGEMENT].
2) Press the  button.
 
f The [ECO MANAGEMENT] screen is displayed.
3) Press as to select [STANDBY MODE].
4) Press qw to switch the item.
 
f The items will switch each time you press the button.
[ECO]Select this item to reduce power consumption during standby. 
[NORMAL]Select this item to use the network function or the serial communication\
 function during standby.  
Note
 
f If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projec\
tor is standing by. Also, you cannot use some 
 
RS-232C protocol commands.
 
f When set to [ECO], it may take approx.10 seconds longer before the proje\
ctor starts projecting after the power is turned on, compared with 
when [NORMAL] is set.
 
f When set to [NORMAL], it may take approx.1 minute to enable the network \
function after connecting the power cord.
 
f The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu 
→
 [INITIALIZE 
 ALL] is 
executed. (
Æ page 76)
[EMULATE]
When controlling the projector on a computer via the < SERIAL IN> terminal, set use of control commands on a 
previously purchased Panasonic projector. This allows the control software for an existing Panasonic projector to \
be inherited and used.
1) Press as to select [EMULATE].
2) Press the  button.
 
f The [EMULATE] screen is displayed.
3) Press  as to select one item.
[DEFAULT]DEFAULT
[D3500]D3500
[D4000]D4000
[D/W5k SERIES]D/W5k SERIES
[D/W/Z6k SERIES]D/W/Z6k SERIES
[L730 SERIES]L730 SERIES
[L780 SERIES]L780 SERIES
[L735 SERIES]L735 SERIES
[L785 SERIES]L785 SERIES
[F/W SERIES]F/W SERIES
[LZ370]LZ370
[LB/W SERIES]LB/W SERIES
[VX500 SERIES]VX500 SERIES
[EZ570 SERIES]EZ570 SERIES
[VW431D]VW431D
4) Press the  button.   
						

							Chapter 4 Settings —
 [PROJECTOR SETUP] menu
74 - ENGLISH
[FUNCTION BUTTON]
The function assigned to the  button of the remote control is \
displayed. You can also release the 
assigned setting.
Releasing assigned function to the  button
1) Press as to select [FUNCTION BUTTON].
2) Press the  button.
 
f The [FUNCTION BUTTON] screen is displayed.
3) Press the  button.
4) When the confirmation screen is displayed, press qw to select [OK] and press the  button.
Note
 
f You can also cancel the assigned settings by displaying the on-screen menu, selecting the menu item to be canceled (main menu, submenu, 
or details menu), and then pressing the  button for at least \
3 seconds.
[AUDIO SETTING]
You can perform more detailed setting for Audio.
Adjusting the volume
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 
f The [AUDIO SETTING] screen is displayed.
3) Press as to select [VOLUME].
4) Press qw to adjust the level.
OperationAdjustmentRange
Press the 
w button.
Increases the volume.
0 ~ 63
Press the  q button.
Decreases the volume.
Setting the mute
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 
f The [AUDIO SETTING] screen is displayed.
3) Press as to select [MUTE].
4) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Audio is output.
[ON]Audio is not output.
Setting the audio output during standby
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 
f The [AUDIO SETTING] screen is displayed.
3) Press as to select [IN STANDBY MODE].   
						

							Chapter 4 Settings —
 [PROJECTOR SETUP] menu
ENGLISH - 75
4) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Disables audio output in the standby mode.
[ON]Enables audio output in the standby mode when [STANDBY MODE] is set to [NORMAL]. At this time, 
press the  button/ button on the remote control or the contr\
ol panel to adjust the 
volume.
Note
 
f When [ECO MANAGEMENT] 
→
 [ST ANDBY MODE] is set to [ECO] (
x page 73), even if [IN STANDBY MODE] is set to [ON], audio 
cannot be output during standby. 
 
f When [IN STANDBY MODE] is set to [ON], the audio output is interrupted during the coolin\
g period after the power is turned off, but this is 
not a malfunction.
Setting audio input selection
Choose the audio input terminal for each input signal.
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 
f The [AUDIO SETTING] screen is displayed.
3) Press as to select one item of [AUDIO IN SELECT].
[HDMI]Set the audio output when [HDMI] input is selected.
[NETWORK]Set the audio output when [NETWORK] input is selected.
4) Press qw to switch the item.
 
f The sub items will switch each time you press the button.
[HDMI]Select one item among [HDMI AUDIO IN] or [AUDIO IN].
[NETWORK]Select one item among [NETWORK AUDIO IN] or [AUDIO IN].
[TEST PATTERN]
Displays the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input 
signal before performing various adjustments.
1) Press as to select [TEST PATTERN].
2) Press the  button.
 
f The test pattern with the [PATTERN CHANGE] individual adjustment screen is displayed.
3) Press qw to switch the test pattern.
 
f The test pattern will switch each time you press the button.
 
f When you press the  button or the  button, it will exit th\
e test pattern and return to the 
sub menu of [PROJECTOR SETUP].
All white
Select a test pattern so that it is easy to make various adjustments.
Color bars (vertical)
Color bars (horizontal)
White cross on the black background 
Black cross on the white background
Cross hatch
Note
 
f The initial setting is All white. The initial screen is Cross hatch if you have assigned it to the  button.   
						

							Chapter 4 Settings —
 [PROJECTOR SETUP] menu
76 - ENGLISH
[FILTER COUNTER]
You can check the filter usage time and set the cleaning cycle for the air filter. Also, reset the filter usage time.
1) Press as to select [FILTER COUNTER].
2) Press the  button.
 
f The [FILTER COUNTER] screen is displayed.
[FILTER COUNTER]Displays the using time of the filter.
[TIMER]Sets the cleaning cycle (time) for the air filter.
[FILTER COUNTER RESET]Resets the filter usage time.
Setting [TIMER] 
Sets the cleaning cycle (time) if you want to clean the air filter periodically
. When the time reaches, an alert 
message  “
FIL
 TER COUNTER has reached the set time. ”
 for filter cleaning is displayed on the projected screen.
1) Press as to select [FILTER COUNTER].
2) Press the  button.
 
f The [FILTER COUNTER] screen is displayed.
3) Press as to select [TIMER].
4) Press qw to switch the setting of the timer.
 
f The items will switch each time you press the button. 
[OFF]Sets when you do not want to display the set time reaching alert message\
.
[1 000 H] ~ [5 000 H]Sets the timer in 1 000 hour increments from 1 000 to 5 000 hours.
Resetting [FILTER COUNTER]
1) Press as to select [FILTER COUNTER].
2) Press the  button.
 
f The [FILTER COUNTER] screen is displayed.
3) Press as to select [FILTER COUNTER RESET].
4) Press the  button.
 
f The [FILTER COUNTER RESET] screen is displayed.
5) Press qw to select [OK] and then press the  button.
[INITIALIZE ALL]
Return various setting values to their factory default settings.
1) Press as to select [INITIALIZE ALL].
2) Press the  button.
 
f The [INITIALIZE ALL] screen is displayed.
3) When the confirmation screen is displayed, press qw to select [OK] and then press the  button.
 
f The [NOW INITIALIZING...] screen is displayed and then the [POWER OFF] screen will be displayed.
4) Press the  button.
 
f The operation of other buttons is disabled.
 
f The initial setting (display language) screen will be displayed when the projector is switched on the next time.
Note
 
f The projector will enter the standby status to reflect the setting values when [INITIALIZE 
ALL] is executed.
 
f When [INITIALIZE ALL] is executed, [STANDBY MODE], [EMULATE], [FILTER COUNTER] and the setting values of [NETWORK] cannot be 
returned to the factory default values. 
 
For details about the initialization of [NETWORK], please refer to [NETWORK]  →
 [INITIALIZE]. (
Æ page 82)    
						

							Chapter 4 Settings —
 [SECURITY] menu
ENGLISH - 77
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an \
item from the sub-menu.
Refer to  “
Navigating through the menu ”
 (x page 48) for the operation of the menu screen.
 
f When the projector is used for the first time
Initial password: Press 
awsqawsq in order, and press the  button.
Attention
 
f When you select the [SECURITY] menu and press the  button, enteri\
ng a password is required. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 
f When the password has been changed previously, enter the changed password, and press the  button.
Note
 
f The entered password is displayed with * marks on the screen.
 
f An error message is displayed on the screen when the entered password is\
 incorrect. Re-enter the correct password.
[PASSWORD]
The [PASSWORD] screen is displayed when press the power <
v/
b > button and turning on the power. When the 
entered password is incorrect, the operation will be restricted to the p\
ower < v/
b > button on the control panel and 
on the remote control .
1) Press as to select [PASSWORD].
2) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Disables the security password entry.
[ON]Enables the security password entry.
Note
 
f The [PASSWORD] setting is set to [OFF] by the factory default or when [INITIALIZE ALL] in [PROJECTOR SETUP] menu (
x page 76) is 
executed.
 
f Change the password periodically that is hard to guess.
 
f The security password is enabled after setting [PASSWORD] to [ON] and press the power <
v/
b > button.
[PASSWORD CHANGE]
Change the security password.
1) Press as to select [PASSWORD CHANGE].
2) Press the  button.
 
f The [PASSWORD CHANGE] screen is displayed.
3) Press asqw and the number ( - ) buttons to set the password.
 
f Up to eight button operations can be set.
4) Press the  button.
5) Re-enter the password for the confirmation.
6) Press the  button.
Note
 
f The entered password is displayed with * marks on the screen.
 
f An error message is displayed on the screen when the entered password is\
 incorrect. Re-enter the correct password.
 
f If numbers have been used for the security password, the security passwo\
rd will need to be initialized again if the remote control is lost. 
Consult your dealer for the initialization method.   
						

							Chapter 4 Settings —
 [SECURITY] menu
78 - ENGLISH
[TEXT DISPLAY]
Overlap the security message (text or image) over the projecting image.
1) Press as to select [TEXT DISPLAY].
2) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Hides the security message.
[ON]Displays the text set in the [SECURITY] menu 
→
 [TEXT CHANGE].
[TEXT CHANGE]
Edit the text to be displayed when [ON] is selected in [TEXT DISPLAY].
1) Press as to select [TEXT CHANGE].
2) Press the  button.
 
f The [TEXT CHANGE] screen is displayed.
3) Press asqw to select the text, and press the  button to enter the text.
4) Press asqw to select [OK], and press the  button.
 
f The text is changed.
[MENU LOCK]
Display the menu by the  button and set whether or not to enable m\
enu operations.
1) Press as to select [MENU LOCK].
2) Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]Unlocks menu operations.
[ON]Locks menu operations.
Note
 
f When the entered password is incorrect after setting [MENU LOCK] to [ON]\
, the  button cannot be operated.
 
f [MENU LOCK] is set to [OFF] at the time of purchase or when [INITIALIZE \
ALL] is executed.
 
f When [MENU LOCK] is set to [ON], after entering the password to release \
the lock, the unlock state is held until the projector enters the 
standby mode.
[MENU LOCK PASSWORD]
The menu lock password can be changed.
1) Press as to select [MENU LOCK PASSWORD].
2) Press the  button.
 
f The [MENU LOCK PASSWORD] screen is displayed.
3) Press asqw to select the text, and press the  button to enter the text.
 
f Up to 16 characters can be input.
4) Press asqw to select [OK], and press the  button.
 
f To cancel, select [CANCEL].
Attention
 
f The initial password is 
“
AAAA ”
 at the time of purchase or when [INITIALIZE  ALL] is executed.
 
f Change the password periodically that is hard to guess.   
						

							Chapter 4 Settings —
 [SECURITY] menu
ENGLISH - 79
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote\
 control.
1) Press as to select [CONTROL DEVICE SETUP].
2) Press the  button.
 
f The [CONTROL DEVICE SETUP] screen is displayed.
3) Press as to select [CONTROL PANEL] or [REMOTE CONTROLLER].
[CONTROL PANEL]You can set the limitation on the control from the control panel.
[REMOTE CONTROLLER]You can set the limitation on the control from the remote control.
4) Press qw to switch between [ENABLE] and [DISABLE]. 
 
f You can set the limitation on the control by the control panel or the rem\
ote control.
[ENABLE]Enable the button operations.
[DISABLE]Disable the button operations.
 
f A confirmation screen will be displayed when you change [ENABLE] to [DISABLE], then proceed to Step 
5).
5) Press qw to select [OK], and then press the  button.
Note
 
f When a button operation is performed on the device set to [DISABLE] , th\
e [PASSWORD] screen is displayed.
 
To continue operations, enter the security password.
 
f The [PASSWORD] screen will disappear when there is no operation for approx.10 \
seconds.
 
f If the operations of both [CONTROL PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 
f Even when you set button operations on the remote control to be disabled\
, operations of the  and  buttons on the remote 
control are enabled.   
						

							Chapter 4 Settings —
 [NETWORK/USB] menu
80 - ENGLISH
[NETWORK/USB] menu
On the menu screen, select [NETWORK/USB] from the main menu, and select \
an item from the sub-menu.
Refer to  “
Navigating through the menu ”
 (x page 48) for the operation of the menu screen.
Note
 
f The on-screen menu (menu screen) of the projector has not the network setting about the wireless LAN. When the wireless module (Model 
No.: ET-WML100E) of the optional accessories is inserted to the projector, please set the wireless LAN by accessing the projector via a 
computer. For detailed, please refer to 
“
W
 eb control function”
 →
 “
[Network config] page ”
 (
x  page 96).
[NAME CHANGE]
Change the name as desired in such a case as the projector needs to be identified on application software.
1) Press as to select [NAME CHANGE].
2) Press the  button.
 
f The [NAME CHANGE] screen is displayed.
3) Select characters with the asqw buttons and press the  button to enter the projector name. 
 
f Up to eight characters can be input.
 
f Select [ALL DELETE] to delete all the entered characters, or press the  button on the remote 
control to delete a character on the cursor in the entry field. 
 
4) Select [OK] with the as buttons and press the  button. 
 
f To cancel the change of the name, press 
asqw to select [CANCEL] and press the  button.
Note
 
f [Name 
□□□□
] (□□□□
 is 4-digit number) is set before the projector leaves the factory.
[MEMORY VIEWER LIGHT]
Note
 
f The menu except for [SET SLIDE] which settings have been changed is not yet effective before the [APPLY] is not executed.
[SET SLIDE]
Start the slide show.
1) Press as to select [SET SLIDE].
2) Press the  button.
 
f Slide show will start.
[SLIDE TRANSITION EFFECT]
Set the slide transition effect when the slide show image is switching.
1) Press as to select [SLIDE TRANSITION EFFECT].
2) Press qw to switch the item.
 
f The items will switch each time you press the button.
[SLIDE RIGHT]Switches the image from the left to the right.
[SLIDE DOWN]Switches the image from the top to the bottom.
[SORT ORDER]
Set the sort order of the slide show.
1) Press as to select [SORT ORDER].