Panasonic Wireless PT-LB50NTE/PT-LB55NTE/PT-LB60NTE, PT-LB50NTU/PT-LB60NTU Instruction Manual

11

Software Installation (cont.)
This  CD-ROM  includes  DirectX  9.0c.  To  transfer  moving  picture  using  the  projector, 
your computer must have DirectX 8.1b or newer.
Click [DirectX 9.0c] on page 10.
The License Agreement for DirectX appears.1
Place a check in the [I accept the 
agreement] checkbox and click 
[Next].
The  DirectX  Runtime  component  install  window 
appears.
2
Click [Next].
•  The  DirectX  component  install  progress  bar 
appears.
•  Do  not  perform  any  other  operations...

12

Installation free Wireless Manager ME 3.0 set up
You can use Wireless Manager ME 3.0 without installing it in the computer.
If  you  copy  Wireless  Manager  ME  3.0  to  a  removable  medium,  such  as  an  SD  card, 
you can use Wireless Manager ME 3.0 without installing it in any computer that permits 
you to access this removal medium.
Insert provided CD-ROM into the CD-ROM drive.
Setup screen appears.1
Click [Installation Free Set Up].
[Direct  CD-ROM  Startup]  and  [Other  Media  Source...

13

Connect
Select Access Port window
Click [] on the desktop, 
or select [Start] → [All Programs] → [Panasonic Wireless 
Display] → [Wireless Manager mobile edition 3.0].
Wireless Manager ME 3.0 starts up, and the “Select Access Port” window appears.
ƒ Network
When  you  specify  the  network  number 
(See  page  46)  set  on  the  projector  from 
one  of  [1],  [2],  [3],  [4],  and  [U  (USER)]
Þ1, 
projectors  that  are  presently  switched 
on  in  the  selected  network  number  are 
displayed...

14

Select the desired projectors, and click [OK].
The  launcher  shown  below  appears  and  the  connection  with  the  projector  is 
established. (“Description of the launcher” →See page 23)
The  launcher  always  appears  on  the  computer  screen,  and  can  be  used  to 
perform various operations.
The  launcher  appears  only  on  the  computer  screen  and  is  not  projected  by  the 
projector.
6
If  the  computer  has  built-in  wireless  LAN  or  has  a  wireless  LAN  card  installed,  the...

15

Connect (cont.)
•  Wireless  connection  cannot  be  made  between  the  projector  and  the  computer.  (See 
page 63)
•  Automatic connection setting (See page 44)
Þ1 • When  a  user  logs  on  a  computer  without  the  administrator  authority,  selectable 
network number is only [U].
• Depending  on  the  computer  and  wireless  LAN  card  used,  easy  wireless  set  up  may  not  be  possible.  If  this  is  the  case,  the  [Network]  setting  of  “Select  Access 
Port”  window  will  be...

16

Connect (cont.)
Connection error messages
One  of  the  following  windows  may  appear  when  a  wireless  connection  cannot  be 
made.
When a setting error for the wireless LAN card has been detected (See page 63)
• Is the wireless LAN card effective?
• Is your wireless LAN card properly recognized?
• Some  wireless  cards  may  allow  easy  wireless  set  up 
connections to function if drivers are updated.
When the Network Bridge setting has been detected (See page 64)
If  you  do  not  expect...

17

Connect (cont.)
Before  starting  Wireless  Manager  ME3.0,  it  is  necessary  to  carry  out  “Computer 
settings” („ on this page) under the administrator authority in advance.
Next, logon as a restricted user or [GUEST], and start Wireless Manager ME 3.0.
Confirm to your system administrator before changing any settings.
Following settings are examples of when using a default setting projector.
ƒ Projector settings Þ“Glossary” (See pages 61-62)
1Turn on the projector and press the [WIRELESS]...

18

Connect (cont.)
If the projector is not displayed, click [Designate] followed by [ADD], then enter 
the IP address set in the projector using the “Access Port Registration” window, 
and click [REGISTER]. (See page 20)
8
Make the SSID, network authentication, data 
encryption and communication mode settings the 
same as those of step 3, and click [OK].
12Start Wireless Manager ME 3.0, and select [U] from 
[Network] of “Select Access Port” window.
13Select the desired projector, and click [OK].
The...

19

Connect (cont.)
You  can  make  the  setting  for  infrastructure  modeÞ  (connection  through  the  access 
point);  however,  confirm  to  your  system  administrator  on  network  settings  before 
changing any settings.
Þ“Glossary” (See page 62)
ƒ Projector settings
1Turn on the projector and press the [WIRELESS] 
button on the remote control.
2Select [USER 1]- [USER 3] from [NETWORK] at the 
wireless menu and press the [ENTER] button.
3
Set the details of network and select [OK].
As for...

20

Connect (cont.)
Þ
“Glossary” (See page 61)
The  newly  registered  connection  is  added  to  the 
connection list in the window shown in step 1.
Click [ADD] and enter the IP addressÞ 
(including its periods) of the 
connection to be added, and then 
click [REGISTER].
2
Click [Designate] at the 
“Select Access Port” 
window.
The window shown to the right appears.
1
When  [Network]  is  set  to  [U]  and  the  desired  projector  is  not  displayed  at  the  “Select 
Access  port”  window,...