Panasonic Wireless PT-LB50NTE/PT-LB55NTE/PT-LB60NTE, PT-LB50NTU/PT-LB60NTU Instruction Manual

							
21

Connect (cont.)
Even  if  there  are  two  or  more  projectors  with  the  same  name,  an  ID  ([Proj]  +  4-digit 
number)  is  assigned  to  each  projector  to  enable  the  projectors  to  be  identified.  When 
you  click  [ID  Search],  a  search  for  the  projector  of  the  specified  ID  is  carried  out  from 
among the projectors that are presently switched on, from all channels other than [U].
It is necessary to know ID in advance. When input selection is switched to WIRELESS 
on  a  projector,  the  ID  appears  on  the  upper  right  of  the  projection  screen  for 
approximately  5  seconds.  If  you  write  down  the  ID  displayed  on  the  “Select  Access 
Port” window in advance, you can search a projector by the ID from next time.
Click [] on the launcher.
The “Select Access Port” window appears.
1
Enter four figures of desired projector’s ID, and click 
[Search].
Start Searching.
3
When the projector of the applicable ID is found, the 
computer will be connected to that projector, and the 
status display of the launcher will turn green.
If appropriate ID is not found, an error message appears.
4
Click [ID Search].
[Projector ID Search] window appears.2
Searching by projector’s ID 
						

							
22

Click [] on the launcher.
The following window appears.
1
Click [Yes].
The  computer  returns  to  the  original  network  settings  when  the  connection  is 
ended.
However, note that some time may be needed to return to the original network 
settings.
2
Connect (cont.)
When the launcher is minimized, right click [] on the notification area to display pop 
up menu and click [End].
Canceling the connection 
						

							
23

The  launcher  always  appears  on  the  computer  screen,  and  can  be  used  to  perform 
various operations.
• Two  types  of  launchers  are  available  in  the  launcher  display  mode,  the  “simple launcher”  and  the  “full  launcher”.  By  default,  the  “simple  launcher”  is  displayed.  The 
launcher display mode can be toggled by clicking 
/ on the right side of the launcher 
window.
  The display mode that the system was in when Wireless Manager ME 3.0 was exited 
is activated the next time the program is started.
• Two launcher button sizes are allowed, the [Small button] and the [Large button]. This  is controlled in [Launcher size setting] in “Option” window. (See page 44)
• Right-click [
] on the notification area to display the menu.
Simple launcherFull launcher
Mute Volume
control
Description of the launcher
Various projection methods
ƒ
Cancel connection
Place in notification area
 Status indication
ƒ Status : Indicate the connecting status.
Connected  computers’  names,  IDs, 
and  their  status  are  displayed  in  the 
pop  up  window  when  the  cursor  is 
on [] of the launcher.
  When connected to one projector
  (Green, lit):  Transmission possible
  (Blue, blinking):  Own computer currently transmitting
    (in the live mode or motion streaming mode)
  (Yellow, lit):  Other user currently transmitting
  (Red, lit):  Communication impossible
  (Black, lit):  When the projector has not been selected
  When connected to multiple projectors
  (Green, lit):  All transmission possible
  (Blue, blinking):  Currently transmitting
  (Yellow, blinking): Communication impossible for more than one unit
  (Red, lit):  All communication impossible
  (Black, lit):  When the projector has not been selected 
						

							
24

Various projection methods (cont.)
Full launcher
 Projection mode select buttons
 „ Live Mode:    D i s p l a y s   t h e   c o m p u t e r   s c r e e n   o v e r   t h e   e n t i r e 
projection screen.
     (See page 25)
 … Multi Live Mode:   Display  the  screens  of  multiple  computers  on  the 
divided  projection  screen.  In  16-screen  index  style, 
[] changes to []. (See page 26)
 Function buttons
 † Selective area transmission: 
     By using the selective area window, you can specify 
the  necessary  information  alone  from  the  computer 
screen, and display it on the projection screen. 
    (See page 35)
 ‡ Secondary display transmission:
       You  can  set  the  computer  screen  and  the  projector 
screen  to  the  multi-monitor  mode,  and  use  the 
computer  screen  as  the  primary  monitor  and  the 
projector  screen  as  the  secondary  monitor.  (See 
page 36)
 ˆ One Shot function:  
The  screen  displayed  when  you  click  the  mouse  is 
projected as a still image. (See page 37)
 ‰ Motion streaming mode:     Projects  a  moving  picture  over  the  entire  projection 
screen. (See page 38)
 Š Shutter function:  Blanks the screen for a moment. (See page 40)
 ‹ WEB control:  Control  a  projector  through  the  WEB  browser  of  a 
computer. (See page 53)
 Œ Select Access Port:   Displays the “Select Access Port” window. 
     (See page 13)
  Option:   Displays the “Option” window. (See page 42)
 Ž Pointer function:   You  can  change  the  shape  of  the  pointer  appearing 
on the projection screen. (See page 40)
‹Š‰ˆ‡†…„ŒŽ 
						

							
25

Various projection methods (cont.)
Press the [MULTI-LIVE SELECT] button on the remote 
control to turn the projection screen into a full 
screen display (the status when no index window is 
displayed).
If  you  press  the  [MULTI-LIVE  SELECT]  button  once  or  twice  when  index 
windows  are  displayed  on  the  projection  screen,  the  screen  will  switch  over  to 
a full screen display.
1
Check the status indication on the launcher to make 
sure that transmission is possible (check that the 
green lamp is lit).
2
Click [] on the launcher.
The current computer screen is transmitted to the selected projector. In the live 
mode the projector is occupied by a single computer, so operations from other 
computers are not possible.
Picture  quality  or  other  options  can  be  set  on  the  “Option”  window  by  clicking 
[] on the launcher.
3
 Quitting live mode
Click [] on the launcher again.
Connect  a  computer  to  a  projector,  and  display  the  computer  screen  over  the  entire 
projection screen.
Live mode
•  For  presentations  in  live  mode,  the  [PAGE  ▲▼]  buttons  on  the  remote  control  will 
function  in  the  same  way  as  the  computer’s  Page  Up  and  Page  Down  keys.  (When 
using  “Presenter  View”  of  “PowerPoint”,  the  [PAGE  ▲▼]  buttons  of  the  remote 
control  correspond  to  Back  space  key  and  Space  key.)  This  means  that  if  you 
run  a  computer  application  that  supports  the  Page  Up  and  Page  Down  keys,  the 
presentation screen can be changed using the remote control.
• Movie play is slowed if [High Definition] is selected in the “Option” window .
• Some  portions  of  images  are  not  projected  under  some  applications  (MS  Office 
Assistant, IME Bar, animation and locus of the mouse cursor, and others).
• If  the  connection  error  occurs  during  projection,  the  message  ‘Stop  “Live  mode”’  will  appear, then restart projection by clicking launcher buttons. 
						

							
26

Various projection methods (cont.)
Multi live mode has “4-screen multi style”, “4-screen index style” and “16-screen index 
style”.
Styles are switched by the projector or the remote control.
 How to switch styles
Either  press  the  [MULTI-LIVE  SELECT]  button  on  the  remote  control  or  select 
[OPTION]  →  [DETAILED  SETUP]  →  [INDEX  WINDOW]  on  the  projector’s  main 
menu and press the [ENTER] button.
Multi live mode
• 4-screen index style
   Display the indexes (small screens) of  up  to  four  computer  screens, 
and  make  one  of  these  screens 
an  enlarged  display.  You  can  also 
temporarily  switch  over  to  a  full 
screen display.
• 16-screen index style
   Display  the  indexes  of  up  to  16  computer  screens.  You  can  also 
t e m p o r a r i l y   s w i t c h   o v e r   o n e   o f 
t h e s e   s c r e e n s   t o   a   f u l l   s c r e e n 
display.
• 4-screen multi style
   Set  the  projector  to  a  full  screen 
d i s p l a y.   A s s i g n   a n   a r e a   o f   o n e 
quarter  of  the  projector  screen  to 
each  of  up  to  four  computers,  and 
project  images  on  the  projector 
screen.
• When the projector starts up, it resumes in the current style the last time the projector was turned off.
• When  transferring  to  the  live  mode,  first  select  the  4-screen  multi  style,  and  then 
click  [
]  on  the  computer.  Please  note  the  connections  to  the  second  and  higher 
numbered computers will be nullified.
• If  you  switch  over  to  a  4-screen  multi  style  when  five  or  more  computers  are  connected  in  a  16-screen  index  style,  the  connections  to  the  fifth  and  higher 
numbered computers will be nullified.
Switching from one style to another
[MULTI-LIVE SELECT]button
[MULTI-LIVE 
SELECT]button
[MULTI-LIVE SELECT]
button 
						

							
27

Various projection methods (cont.)
Check the status indication on the launcher to make 
sure that transmission is possible (check that the 
green lamp is lit).
2
Press the [MULTI-LIVE SELECT] button on the remote 
control to turn the projection screen into a full screen 
display (the status when no index window is displayed).
If  you  press  the  [MULTI-LIVE  SELECT]  button  once  or  twice  when  index 
windows  are  displayed  on  the  projection  screen,  the  screen  will  switch  over  to 
a full screen display.
1
Click [] on the launcher.
The window shown to the right appears.
3
Select and click the projection position.
The  computer  image  is  transmitted  to  the  selected  quarter 
of the projection screen.
4
 Switching to a different position
Select  and  click  a  different  projection  position  in 
step 4 above.
 Enlarged display
If  []  is  clicked  with  a  computer,  projector  screens 
temporarily  change  to  full  screen  display.  To  return 
to  the  original  display,  click  [
]  with  the  computer 
that click [
] and select original projection positions 
with each computer.
 Quitting 4-screen multi style
Select  and  click  the  checked  position  in  step  4 
above.
• In the 4-screen multi style, the computer screens from all the computers connected to  the projector can be transmitted to the projector. (If an image from another computer 
has been sent to the image position where an image is already displayed, the existing 
image is replaced by the new image.)
• If  the  connection  error  occurs  during  projection,  the  message  ‘Stop  “Live  mode”’  will  appear, then restart projection by clicking launcher buttons.
• Picture quality or other options can be set on the “Option” window by clicking [
] on 
the launcher.
4-screen multi style
Connect  up  to  four  computers  to  one  projector,  and  then  divide  the  projector  screen 
into  four  parts,  and  simultaneously  display  the  screens  for  the  four  computers  on  the 
projector screen. 
						

							
28

Various projection methods (cont.)
When  the  projector  is  set  to  “4-screen  index  style”,  connect  up  to  four  computers  to 
one  projector,  and  then  simultaneously  display  the  screens  for  the  four  computers  on 
the index windows and also on a large screen.
Check the status indication on the launcher to make 
sure that transmission is possible (check that the 
green lamp is lit).
2
Press the [MULTI-LIVE SELECT] button of the remote 
control to switch the projection screen to “4- screen 
index style”. (See page 26)
1
Click [] on the launcher.
The window shown to the right appears.
3
Select and click the projection position.
T h e   c o m p u t e r   i m a g e   i s   t r a n s m i t t e d   t o   t h e   a r e a   o f 
corresponding window.4
4-screen index style 
						

							
29

 Quitting 4-screen index style
Select  and  click  the  checked  position  in  step  4  on  the  previous 
page.
Various projection methods (cont.)
 Enlarged display
• Use  the  []  buttons  on  the  remote  control  to  move  the 
focus  (yellow  box)  to  the  image  to  be  enlarged,  and  press 
the  [ENTER]  button.  The  image  is  enlarged  and  displayed 
at the top of the projection screen.
• The  image  display  will  fill  the  entire  screen  if  the  [ENTER] 
button is pressed again.
• To  return  to  the  4-screen  index  style,  press  the  [ENTER] 
button again.
•  While  an  enlarged  image  is  displayed,  the  [PAGE  ▲▼]  buttons  on  the  remote  control  will  function  in  the  same  way  as  the  computer’s  Page  Up  and  Page  Down 
keys.  (When  using  “Presenter  View”  of  “PowerPoint”,  the  [PAGE  ▲▼] buttons  of  the 
remote  control  correspond  to  Back  space  key  and  Space  key.)  This  means  that  if 
you run a computer application that supports the Page Up and Page Down keys, the 
presentation screen can be changed using the remote control.
 • Picture quality or other options can be set on the “Option” window by clicking [
] on 
the launcher.
 •  If  the  connection  error  occurs  during  projection,  the  message  ‘Stop  “Live  mode”’  will 
appear, then restart projection by clicking launcher buttons.
In the 4-screen index style, the green status display lamp remains lit.
Other computers can send images only to the windows which are not being used. 
						

							
30

Various projection methods (cont.)
Check the status indication on the launcher to make 
sure that transmission is possible (check that the 
green lamp is lit).
2
Press the [MULTI-LIVE SELECT] button of the remote 
control to switch the projection screen to “16-screen 
index style”. (See page 26)
1
Click [] on the launcher.
The  computer  images  are  automatically  sent  to  the  empty  windows  on  the  16-
screen display. Display position is not selectable.
3
 Enlarged display
•  Use  the  [▲▼]  buttons  on  the  remote  control  to  move  the  focus  (yellow  box) 
to  the  image  to  be  enlarged  and  press  [ENTER]  to  expand  that  image  to  fill  the 
display.
• Press [ENTER] again to return to the 16-screen index style.
Toggle between
these with the
[ENTER] button.
When  the  projector  is  set  to  “16-screen  index  style”,  connect  up  to  16  computers  to 
one  projector,  and  simultaneously  display  the  screens  for  the  16  computers  on  index 
windows and also on a large screen.
•  While  an  enlarged  image  is  displayed,  the  [PAGE  ▲▼]  buttons  on  the  remote control  will  function  in  the  same  way  as  the  computer’s  Page  Up  and  Page  Down 
keys.  (When  using  “Presenter  View”  of  “PowerPoint”,  the  [PAGE  ▲▼] buttons  of  the 
remote  control  correspond  to  Back  space  key  and  Space  key.)  This  means  that  if 
you run a computer application that supports the Page Up and Page Down keys, the 
presentation screen can be changed using the remote control.
 • Picture quality or other options can be set on the “Option” window by clicking [
] on 
the launcher.
 •  If  the  connection  error  occurs  during  projection,  the  message  ‘Stop  “Live  mode”’  will 
appear, then restart projection by clicking launcher buttons.
 Quitting 16-screen index style
Click [] on the launcher again.
16-screen index style