Panasonic Wireless PT-LB50NTE/PT-LB55NTE/PT-LB60NTE, PT-LB50NTU/PT-LB60NTU Instruction Manual

							
51

Network setting of the projector (cont.)
 ENCRYPTION  :   Select  the  encryption  method  to  be  used  for  communication 
between the projector and the network.
  NONE   :   Select when transmit without encryption. It is selectable only when  [AUTHENTICATION] is [OPEN] or [SHARED].
  WEP
Þ    :  Select when ENCRYPTION is WEP.
  TKIPÞ    :  Select when ENCRYPTION is TKIP. 
        Selectable when [AUTHENTICATION] is [WPA-PSK].
  AES
Þ    :  Select when ENCRYPTION is AES. 
        Selectable when [AUTHENTICATION] is [WPA-PSK].
Additionally perform the following setting using the [AUTHENTICA TION] setting.
  When  setting  [OPEN]  or  [SHARED]  as  authentication  and  setting  [WEP]  as  the 
encryption method:
  DEFAULT KEY :  Set 1  – 4 numerals for the default key.
  KEY 1 – 4  :  Set these to match the WEP key registered in [DEFAULT KEY].
          Either the 64-bit or 128-bit WEP key can be set.  For the 64-bit key,  input  five  alphanumerics  (or  a  10-digit  string  for  the  hexadecimal 
format)  for  the  128-bit  key,  input  13  alphanumerics  (or  a  26-digit 
string for the hexadecimal format).
 When setting [WPA-PSK] as authentication : Set key and select [OK].
         Input  either  8  to  63  alphanumerics  or  a  64  digit  string  in  the 
hexadecimal format.
Þ
“Glossary” (See page 62)
Important  video/audio  data  is  protected  because  AESÞ  encryption  processing  takes 
place in advance for all network numbers, even if [ENCRYPTION] is set to [NONE].
Þ
“Glossary” (See page 62)
DETAILED SETUP
CANCEL
SELECT
USER1 3/3
DEF AULT KEY
KEY1
KEY2
KEY3
KEY4
* * * * * * * *
* * * * * * * * * * * * * * * *
* * * * * * * *
1
OKCANCELRETURN 
						

							
52

Network setting of the projector (cont.)
The  following  is  set  as  [USER1]-[USER3]  in  the  wireless  menu  before  the  projector 
leaves the factory.SSID  :  Panasonic Projector
DHCP  :  OFF
IP ADDRESS  :  192.168.10.100
SUBNETMASK  :  255.255.255.0
GATEWAY  :  192.168.10.1
MODE  :  AD HOC
AUTHENTICATION  :  OPEN
ENCRYPTION  :  NONE
Default settings of [USER1]-[USER3] 
						

							
53

Using WebBrowser
Select [WEB CONTROL] on the wireless menu.1
Select [ON] or [OFF] with the [] buttons.
ON  : This enables control on the WebBrowser.
OFF : This disables control on the WebBrowser.2
Control a projector through the WEB browser of a computer. It is called “WEB Control”.
(The example is when using Microsoft Internet Explorer.)
• Connect projector and computer. (See page 14)
• Release the proxy settings of the Web Browser used. (See next page)
• Enable JavaScript.  (See page 55)
RETURN
SELECT
PT-LB50NTE
LANGUAGE
OPTION
SECURITY
WIRELESS
POSITION
PICTURENETWORK
NAME CHANGE
INPUT PASSWORD
PASSWORD CHANGE
WEB CONTROL
STATUS
INITIALIZEUSER1
ON
OFF
Before using the WEB control
• When  the  projector  settings  have  been  changed  using  a  WebBrowser,  the  projector  will not appear on the connection list until the projector network is switched to [USER 
1] - [USER 3].
• After  the  projector  network  has  been  switched  to  [USER  1]  -  [USER  3],  manually  release the proxy settings of the WebBrowser used.
ƒ Projector settings
Set the [WEB CONTROL] of wireless menu [ON]. 
						

							
54

Using WebBrowser (cont.)
Open “Internet Properties” window.
Click  [Start]  →  [Control  Panel]  →  [Network  and  Internet  Connections]  → 
[Internet Option].
1
2Open [Connections] → [LAN 
Settings].
3If [Use a proxy server for your LAN] has been checked, 
remove the check.
If [Use automatic configuration script] has been 
checked, remove the check.
4Click [OK].
 Proxy server settings
Release the proxy settings of the WebBrowser used.
„ Computer settings 
						

							
55

Using WebBrowser (cont.)
 Enabling JavaScript
If JavaScript has been set to disable, enable it.
2Select [Security] and set the security level to [Default 
Level], or select [Custom Level] and check the [Enable] 
checkbox under [Active scripting]. Open “Internet Properties” window.
Click  [Start]  →  [Control  Panel]  →  [Network  and  Internet  Connections]  → 
[Internet Option].
1 
						

							
56

Accessing from the Web browser

Using WebBrowser (cont.)
1Click [] on the launcher.
Or start up the WebBrowser, and enter the IP address 
set by the projector.
WebBrowser starts up and the page of “Projector control window” appears.
2Select the language to be displayed, and if a web 
access password has been set, enter that password.
3Click [ENTER].
“Basic control window” appears. (Next page)
•  Password used in this page is for accessing the web control window. (See page 58) 
  This password is different from the password set in page 47 for accessing a projector.
• If  you  forget  the  password,  perform  [INITIALIZE]  using  the  wireless  menu  of  the  projector,  and  set  a  password  once  again  using  the  “Change  Password”  window  on 
the web browser (See page 58).
• The top window may not appear depending on the WebBrowser. In this case start up  WebBrowser again, or press the [Ctrl] + [R] keys for example to update the screen.
• Connection cannot be made while the WebBrowser is set to dial-up network.
  Cancel the dial-up network setting.
• It may take some moments for WebBrowser to start up. 
						

							
57

You can make various projector settings.
Click [Projector Control]→[Basic] or [Advanced], when moving from other 
pages.
Using WebBrowser (cont.)
Projector control window
 Basic control window Option control window
Connection  with  the  projector  may  not  be  possible  immediately  after  the  power  is 
turned on. In this case wait a bit and then make the connection again. 
						

							
58

Using WebBrowser (cont.)
This page indicates the projector status.
Click [Status].
Monitor information window
The monitor information is refreshed at fixed intervals, but the current exact information 
can be checked by clicking [View] → [Refresh].
Set the password to access to “Projector control window”.
Enter the old password and new password, and click [OK].
You can enter a password up to 16 characters (upper case/lower case) and 
symbols.
Password changing window 
						

							
59

3Click [NEXT].
The settings will be registered.
 Making the above settings effective
 Select  [NETWORK]  in  the  wireless  menu  of  the  projector,  and  use  the  []  buttons 
to select the network set in this page and press the [ENTER] button.
Using WebBrowser (cont.)
You  can  make  detail  network  settings  on  projector,  when  connecting  without  the 
administrator  authority  or  when  connecting  through  an  access  point  (infrastructure 
mode).
Network setting window
1Click [Network setting] on the 
menu and click [NEXT].
The setting window appears.
2Set detail network settings.
Settings  in  this  page  are  the  same  when 
setting  [USER  1]-[USER  3]  from  wireless 
menu of the projector. (See page 49)
Important  video/audio  data  is  protected  because  AESÞ  encryption  processing  takes 
place in advance for all network numbers, even if [ENCRYPTION] is set to [NONE].
Þ
“Glossary” (See page 62) 
						

							
60

Software Uninstall
Wireless Manager ME 3.0
From the desktop, select [Start] → [All Programs] → 
[Panasonic Wireless Display] → [Uninstall Wireless Manager 
mobile edition 3.0].
Follow the instructions appearing on the screen and uninstall the software.