Philips Hts335w User Manual

							41
English
Video Setup Page (underlined options are the factory default settings)
Setup Menu Options (c o n t i n u e d )
HDMI Setup
 It provides the picture settings to enhance the appearance and 
picture quality for disc playback.  This feature is only applicable if 
you have connected this unit to a HDMI-compatible TV/device.
  { Wide Screen Format } – Select a suitable screen display. 
Note:  This feature is only available if you have selected the { 16:9 
Wide Screen } in { TV Display } setup option.
{ Superwide }  
Display the 4:3 picture disc on the wide-screen TV 
with non-linear stretching (centre position of the 
screen is stretched less than the side).
{ 4:3 Pillar Box }
Display the 4:3 picture disc on the wide-screen TV 
without stretching.  Black bars will be shown on 
the both sides of the TV screen. 
{ Off }
No aspect ratio adjustment is made when this 
option is selected.
Note:  The { Superwide } is only applicable for 
resolution: 720p or 1080i.
{ HDMI Video }–  Select a suitable video resolution depending 
on the capability of the connected TV/device 
to further enhance the HDMI video output.
{ 480p }
Progressive output in 480 lines for NTSC TV.
{ 576p }
Progressive output in 576 lines for PAL TV.
{ 720p } - (if a HDMI TV is connected)
Progressive output upscale to 720 lines.
{ 1080i } - (if a HDMI TV is connected)
Interlaced output upscale to 1080 lines. 
{ Auto } 
The video output automatically follows the 
display’s supported resolution.
Note:  If no display appears on the TV due to 
unsupported resolution, use the Scart cable to 
connect this unit and your TV. Turn on your TV to 
the correct video input channel and adjust the 
resolution setting to 480p/576p.
Component
 Select the type of video output that matches the video 
connection between this unit and your TV.
{ YUV }    –  For component video (Y Pb Pr) connection.
{ RGB }    –  For SCART connection.
 
						

							42
EnglishPreference Page (underlined options are the factory default settings)
Audio
 Select the preferred audio language for DVDs with multiple 
sound tracks.  
Subtitle
 Select the preferred subtitle language for DVD playback.
Disc Menu
 Select the preferred disc menu language for DVD playback.
Note:  If the selected audio/subtitle/disc menu language is not available on 
the DVD, the disc’s default language will be used instead.
Parental
 This is to prohibit viewing of discs that had exceeded the limits 
you set. It works only on the DVDs with parental level assigned 
to the complete disc or to certain scenes on the disc. 
1) Use ST keys to select a rating level from 1 to 8 and press OK.  
2) Use the numeric keypad 0-9 on the remote control to enter your 
six-digit password.
Notes:  
–  The ratings are country-dependent (‘1’ is considered material that is 
least offensive and ‘8’ is most offensive). To disable parental controls and 
allow all discs to play, select ‘8’.
–  Some DVDs are not encoded with a rating though the movie rating 
may be printed on the disc cover. The rating level feature does not 
prohibit playback of such discs. VCD, SVCD and CD have no level 
indication, so parental control has no effect on these type of discs.
–  DVDs that are rated higher than the level you selected will not be 
played unless you enter the same six-digit password. 
Surround
 Set the preferred surround setting when the unit is powered up.
{ On }   –  Turn on to multi-channel surround mode. 
{ Last Setting }  –  Turn on to the last surround setting. 
PBC
 Play Back Control feature is applicable for VCD/SVCD only. It 
allows you to play Video CDs (2.0) interactively, following the 
menu on the display.  
{ On }   –  The index menu (if available) appears on the 
TV when you load a VCD/SVCD.
{ Off }   –  The VCD/SVCD skips the index menu and 
playback directly from the beginning.
Setup Menu Options (continued)
 
						

							43
English
Preference Page (underlined options are the factory default settings)
MP3/JPEG Nav
 MP3/JPEG Navigator can only be set if the disc is recorded with a 
menu. It allows you to select different display menus for easy 
navigation.
{ Without Menu } – Display all the fi les contained in the MP3/
Picture disc.
{ With Menu }  –  Display the folder menu of the MP3/Picture 
disc.
Note:  This unit can only display 650 fi les/folder in the directory.
Password
 The password is used for the Disc Lock and Parental. The default 
password is ‘136900’. To change the password:
1) Press OK to access the change password menu.
Old Password
New Password
Confirm PWDChange Password
OK
2) Use the numeric keypad 0-9 on the remote control to 
enter your existing six-digit password at { Old Password }.
Note:  When doing this for the fi rst time or if you forget your existing  
password, key in ‘136900’.
3)  Enter the new six-digit password at { New Password }.
4)  Enter the new six-digit password again at { Confi rm PWD }.
5) Press OK to confi rm and exit the menu.
DivX Subtitle
 Select the font type that supports the recorded DivX subtitle.
{ Central Europe } – Display Central Europe fonts.
{ Cyrillic }    – Display Cyrillic fonts.
{ Greek }     – Display Greek subtitle fonts.
{ Standard }     – Display a standard list of Roman subtitle    
 fonts provided by this unit.
{ Hebrew }     – Display Hebrew subtitle fonts.
{ Chinese (Simp) } – Display Simplifi ed Chinese fonts.
{ Korean }     – Display Korean fonts.
Default
 This feature enables you to reset all the setup menu options and 
your personal settings to the factory defaults, except your 
password for the Disc Lock and Parental.  
 Press OK to confi rm the default reset.
Setup Menu Options (c o n t i n u e d )
 
						

							44
English
Radio Operations
Before you start ...
Make sure the FM and AM/MW 
antennas antennas 
are connected.are connected.
Tuning to radio stations
A Press SOURCE repeatedly until ‘FM’ 
appears on the display panel (or press 
RADIO on the remote control).
B Press W / X on the remote control to 
start tuning.

						

							45
English
Radio Operations (c o n t i n u e d )
B
 Press u.

						

							46
English
Sound and Volume Controls
SLEEP
MUTE 
SURROUNDVOL+-
SOUND
Volume control
z Press VOL +/- to increase or 
decrease the volume level. 

						

							47
English
Installing the latest software
Periodically Philips will issue software 
upgrades to enhance the user experience. 
A Get the software version of this unit by 
pressing OPEN/CLOSE ç to open the 
disc compartment 
B Press DISPLAY on the remote control. 

						

							48
English
Tr o u b l e s h o o t i n g
WARNING
Under no circumstances should you try to repair the system yourself, as this will
invalidate the warranty. Never open the system as there is a risk of electric shock.
If a fault occurs, fi rst check the points listed below before taking the system for repair. 
If you are unable to solve a problem by following these instructions, consult your dealer or
Philips for help.
No power.
No picture.
Completely distorted picture 
or black/white picture.
No sound or distorted sound.
No surround sound effect 
from the speakers.
The remote control does not 
function properly.–   Press STANDBY-ON on the unit to turn on the 
power.
–   Make sure the mains cord is properly connected and 
the AC outlet has power.
–  Refer to your TVs manual for correct Video In 
channel  selection. Change the TV channel until you 
see the DVD screen.
–  Press DISC/USB to select disc mode.
–  If this happens when you turn on the progressive scan 
feature, wait for 15 seconds for the auto recovery or 
switch back to the default mode as below:
  1)  Press OPEN/CLOSE ç.
  2)  Press W on the remote control.
  3)  Press AUDIO on the remote control. 
–  Check the video connection.
–  Sometimes a small amount of picture distortion may  
 appear. This is not a malfunction.
–  The disc is dirty. Clean the disc.
–  Adjust the volume.
–  Check the speaker connections and settings.
–  Make sure that the audio cables are connected and 
press SOURCE to select the correct input source (for 
example, TV or AUX/DI) to choose the device that 
you want to hear through this unit.
–  Press SURROUND to select a correct surround 
sound setting.
–  Make sure that the source you are playing is recorded 
or broadcast in surround sound (DTS, Dolby Digital, 
etc).
–  Select the source you want to play (for example, 
DISC/USB or RADIO) before pressing the function 
button (X, í / ë).
–  Reduce the distance between the remote control and 
this unit.
–  Batteries are weak, replace the batteries.
–  Point the remote control directly toward the IR sensor.  Problem (General)  Solution
 
						

							49
EnglishThe unit does not start 
playback.
The aspect ratio of the screen 
cannot be changed even 
though you have set the TV 
display.
Cannot activate some features 
e.g. Angles, Subtitles, or 
multi-language Audio.
Not able to select some items 
in the setup/system menu.
Unable to play DivX movies.
Radio reception is poor.
The unit does not work.–  Insert a readable disc with the playback side facing 
down. The DVD+R/CD-R must be Finalised.
–  Make sure the disc is not scratched or warped. 
–  Press SETUP to turn off the system setup menu  
 screen.
–  You may need to enter the password in order to 
unlock the disc for playback.
–  Moisture may have condensed inside this unit. 
Remove the disc and leave this unit turned on for 
about an hour.
–  The aspect ratio is fi xed on the DVD disc.
–  Depending on the TV, it may not be possible to 
change the aspect ratio.
–  The features may not be available on the DVD.
–  Changing the language for the sound or subtitle is  
 prohibited on this DVD.
–  Press STOP button twice before selecting the system 
setup menu.
–  Depending on the disc availability, some menu items 
cannot be selected.
–  Ensure that the DivX fi le is encoded according to the  
 ‘Home Theatre Profi le’ with the DivX encoder.
–  Check that the DivX movie downloaded is a complete  
fi le.
–  If the signal is too weak, adjust the antenna or 
connect an external antenna for better reception.
–  Increase the distance between this unit and your TV 
or VCR.
–  Tune in to the correct frequency.
–  Place the antenna further away from any equipment 
that may be causing the interference.
–  Disconnect the power cord from the power outlet 
for a few minutes. Reconnect the power cord and try 
to operate again as usual.
 Problem (Playback)  Solution
Tr o u b l e s h o o t i n g  (c o n t i n u e d )
 
						

							50
English Problem (USB/HDMI)  Solution
Tr o u b l e s h o o t i n g  (c o n t i n u e d )
The contents of the USB fl ash 
drive cannot be read.
Slow operation of the USB 
fl ash drive.
No audio output from HDMI 
connection.
No video output from HDMI 
connection. 
 
If the indicator on the wireless 
transmitter blinks 
continuously for more than 
one minute.–  The USB fl ash drive format is not compatible with this 
unit.
–  Drive is formatted with a different fi le system which is 
not supported by this unit (e.g. NTFS).
–  Large fi le size or high memory USB fl ash drive takes 
longer time to read and display on the TV.
–   You will not hear any sound from the HDMI output if 
the source device is only DVI/HDCP (High-bandwidth 
Digital Content Protection)-compatible.
–   It is not possible to output SACD or copy-controlled 
DVD-Audio sources from the HDMI connection.
–   Make sure that the audio output setting is not turned 
off. See ‘Setup Menu Options - { Audio Setup Page - 
HDMI Audio }’ for details.
–  HDMI connection can only be made to HDMI-
equipped devices with HDCP (High Bandwidth Digital 
Content Protection).  If you wish to connect to a DVI 
connector (equipped with HDCP), you will need a 
separate adaptor (DVI to HDMI).
–   Make sure the resolution of this unit matches the 
device you have connected using the HDMI.  See 
‘Setup Menu Options - { Video Setup Page - HDMI 
Setup - HDMI Video }’ for details.  
–   The transmitter may have been swapped with another 
transmitter supplied with other receiver.
–   Turn off all connected devices.
–   Turn on the connected home theatre system.
–   Press and hold the CONNECT button on the 
transmitter for fi ve seconds.  Release the CONNECT 
button.
–   Turn on the wireless receiver.