Philips Velo 1 Manual

11
To install the Windows CE 2.0 ROM Miniature Card
1Back up all files on your Velo 1 as described above.
2Turn off your Velo 1.
3On the bottom of your Velo 1, slide back the latch to
release the door to the Flash/ROM Miniature Card slot and
remove the door to the slot and the dummy card or Flash
Card.
4Insert the ROM Miniature Card into the slot, and push the
card down until it snaps into place.
5Replace the door.
Step 1: Set Up Your Velo 1 for the Upgrade 

12
Philips Velo™1 User’s Guide
Note:Do not remove the Windows CE 2.0 ROM Miniature Card
from the Flash/ROM Miniature Card slot. After you install the ROM
Miniature Card, you will be unable to use the Flash/ROM Miniature
Card slot for other cards, such as flash memory upgrades or programs
that come on Miniature Cards.
1d: Install more RAM in your Velo 1.
If you do not have 12 MB of RAM installed on your Velo 1 you
will need to install enough RAM to bring your device up to 12
MB in order to proceed with...

13
Step 1: If you purchased the Velo 1 with 12 MB
of DRAM and the Microsoft Windows CE 2.0
Upgrade Card already installed, start here:
1Plug the supplied AC adapter into your Velo 1 and a wall
outlet.
2Press the Power button to turn on the Velo 1.
3The Setup Wizard appears; ignore it for now.
4 Unplug the AC adapter from the Velo 1.
5Insert the main battery and activate the backup battery.
(See the figures on the next page.)
aSlide the main battery door lock.
bOpen and detach the battery door.
cPull out...

14
Philips Velo™1 User’s Guide
Bottom of Velo 1
-
+
Bottom view showing rechargeable battery pack insertion 

15
Step 2: Install Windows CE Services 2.0
On Your Desktop Computer
System requirements
The minimum PC requirements for running Windows CE Services 2.0
are as follows:
wMicrosoft Windows NT
® Workstation 4.0 or Windows 95
wDesktop computer with a 486/33DX or higher processor
(Pentium P90 recommended)
w12 MB of memory for Windows NT Workstation 4.0
w8 MB of memory (12 MB recommended) for Windows 95
wHard disk drive with 10 to 50 MB of available hard-disk
space (actual requirements will vary, based on...

16
Philips Velo™1 User’s Guide
In addition to Windows CE Services 2.0, the Microsoft Windows CE
compact disc contains Microsoft Schedule+, updates to the Windows
Messaging System (Microsoft Exchange), and Windows 95 Dial-Up
Networking and some optional items. The installation program will
check for and install these components as necessary to ensure that
you can set up and run Windows CE Services 2.0, as well as
applications including Pocket PowerPoint
® and Pocket Streets.
Installing Windows CE Services...

17
Step 3:  Prepare Your Velo 1 and Your
Desktop Computer for Velo 1 Application
Installation
Before you install Velo 1 applications, you must set the PC
connection on your Velo 1. Instructions for setting the connection
are below.
If you are an experienced user, you may want to set up your
Velo 1 and your computer to make the installation procedure go
much more quickly. Making these changes requires many more
steps, but greatly speeds up the installation process. If you choose
to make these changes,...

18
Philips Velo™1 User’s Guide
To increase the speed of data transfer between your
Velo 1 and desktop computer
1Disconnect the Velo 1 from the desktop computer.
2On the Velo 1, tap Start, tap Programs, tap
Communication, then tap Remote Networking.
3Double-tap Make New Connection.
4Under Type a name for the connection, type a name
(such as “Fastest”), then tap Next.
5Tap Configure, and then in the Baud Rate list, select the
desired rate (typically 115,200 baud is the fastest), then
tap 
.
6Tap Finish....

19
Step 3: Prepare for Velo 1 Application Installation
15If you are using Windows 95:
aOn your desktop computer, click Start, point to
Settings, click Control Panel, then double-click the
System icon.
bClick the Device Manager tab, double-click Modem,
then select the port to which your Velo 1 is connected.
cClick Properties, click the Modem tab, and then under
Maximum speed select the same rate you specified on
your Velo 1. Tap 
 to close the window.
dClick OK, then click OK again to close the System...

20
Philips Velo™1 User’s Guide
Step 4: Install Velo 1 Applications From
the 
Velo 1 Upgrade CD
The Philips Velo 1 Upgrade compact disc includes programs and
components of the Velo 1 applications and operating system. You
must install these components to ensure that all features of your
Velo 1 will function as intended. To install these programs from
the CD, follow these steps:
1Connect the Velo Dock’s cable to the desktop computer’s
serial port.
2Plug the AC power adapter into the DC jack on your Velo...