Pioneer Rvd Xg10 Projector Specifications

RVD-XG10
RS-232C
COMMAND MANUAL
Ver.1.00 

CONTENTS
----------------------------------------------------------------------------------------------------------------
1. CONNECTIONS
2. COMMANDS
 2.0 Command List
 2.1 Basic Commands
 2.2 Setup Commands
 2.3 Adjustment Commands
 2.4 Reset Commands
 2.5 Integrator Commands
3. NOTES 

1. CONNECTIONS
----------------------------------------------------------------------------------------------------------------
(1) Communication software setup
The interface used complies with the RS-232C. Set the communication software as listed below.
Baud rate : 9600 bps
Number of bits : 7 bits
Parity : Non parity
Stop bit : 1 bit
(2) Computer connection
Connect an external computer using a straight cable with 9-pin, D-SUB connectors.
The connectors should be wired as shown below.
Fig. 1...

2. COMMANDS
----------------------------------------------------------------------------------------------------------------
 2.0 Command List
 The following tables show the availability of each command according to the status of the set. Each command is
available in the conditions marked .  (C) indicates that the command is available only when the COMP. 1 or COMP.
2 input is selected, and  (V) indicates that it is available only when the video input is selected. a, aa and b in the
Command columns...

Table 3  Adjustment Commands
Standby Power
ONSet
MenuONRS-232C
Adjust
ON
ZUP
ZDW
FUP
FDW
VOLdddd = 0 to 60
FRQdddddddd = 264 to 4104›(C)
PHSdddd = 0 to 19›(C)
PSaa =L/R/U/D›(C)
ATS›(C)
CNTdddd = -51 to 0
BRTdddd = -25 to 25
COLdddd = -25 to 25Adjusts the color.›(V)
TNTdddd = -25 to 25Adjusts the tint.›(V)
SHPdddd = -25 to 25Adjusts the sharpness.›(V)
Caba =R/B, b =L/R/U/DAdjusts the convergence.Set StatusCommand Function
Zooming toward Wide-angle.
Zooming toward Telescopic.
Focusing toward Far.Focusing...

2.1 Basic Commands
       Command NameFunction
2.1.1  PON/POF Power ON/OFF switching.
2.1.2  INV/IN1/IN2 Input selection.
2.1.3  AK, EO, MSTransmission/reception check.
2.1.4  GST, GPP, GAD Current set status check.
2.1.5  AJY/AJN Start/end of adjustment using commands. 

2.1.1  PON/POF Commands
----------------------------------------------------------------------------------------------------------------
Function: Switches the power mode between standby  power ON.
----------------------------------------------------------------------------------------------------------------
Syntax: PON[CR], POF[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function::
  Remote   : [STANDBY/ON]  * Cyclic...

2.1.2  INV/IN1/IN2 Commands
----------------------------------------------------------------------------------------------------------------
Function: Selects the input.
----------------------------------------------------------------------------------------------------------------
Syntax: INV[CR], IN1[CR], IN2[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function::
  Remote:    [COMP. 1], [COMP. 2], [VIDEO]
  Main unit:...

2.1.3  AK, EO and MS Commands
----------------------------------------------------------------------------------------------------------------
Function: Checks the transmission and reception through RS-232C.
----------------------------------------------------------------------------------------------------------------
Syntax: AKY[CR], AKN[CR], EN[CR], EOF[CR], MSY[CR], MSN[CR]
----------------------------------------------------------------------------------------------------------------
Initial status:...

2.1.4  GST, GPP and GAD Commands
----------------------------------------------------------------------------------------------------------------
Function: Checks the current status of the set.
----------------------------------------------------------------------------------------------------------------
Syntax: GST[CR], GPP[CR], GAD[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: None....