Planar Pr5022 Projector User Manual

DLP® Projector – User’s Manual 
Item Label Description See page: 
8.  Height-adjuster but-
ton 
Push to release height adjuster 17 
Important: 
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. 
Do not obstruct any of the ventilation openings. 
Top view—On-screen Display (OSD) buttons and LEDs 
 
Item Label Description See page: 
1.  Keystone/ 
Down cursor
Corrects image-trapezoid (wider bottom) effect  
Navigates and changes settings in the OSD...

DLP® Projector – User’s Manual 
Item Label Description See page: 
6.  Enter Changes settings in the OSD 20 
7.  VOL+/ 
Right cursor 
Increases volume 
Navigates and changes settings in the OSD 20 
8.  Auto Optimizes image size, position, and resolution 
Navigates and changes settings in the OSD 
9.  Menu Opens and exits the OSD 
10.  Source Detects the input device 
11.  Power Turns the projector on or off 
13 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 4 –  

DLP® Projector – User’s Manual 
Rear view 
 
Item Label Description See page:
1.  Rear IR receiver Receiver for IR signal from remote control 7 
2.  DVI-D Connect a DVI-D cable (not supplied) from a com-
puter 
3.  VGA IN Connect a VGA cable (supplied)  from a computer 
4.  VGA OUT Connect to a monitor (not supplied) 
5.  S-video Connect the S-video cable (not supplied) from a video 
device 
6.  Video Connect a composite video cable (supplied) from a 
video device. 
7.  Audio in-R Connect the audio...

DLP® Projector – User’s Manual 
Note: 
If your video equipment has both S-video and RCA jacks (composite video) connect to the S-video 
connector.  
S-video provides a better quality signal. 
Bottom view 
 
 
Item Label Description See page: 
1.  Ceiling support 
holes 
Contact your dealer for information on mount-
ing the projector on a ceiling.  
2.  Height adjuster but-
ton 
Push to release height adjuster 
3.  Height adjuster Adjuster drops down when adjuster button is 
pushed 
4.  Tilt adjuster...

DLP® Projector – User’s Manual 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluores-
cent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between 
the remote control and the projector is obstructed, you can bounce the signal off certain reflective sur-
faces such as projector screens. 
 
3. The buttons and keys on the...

DLP® Projector – User’s Manual 
Item Label Description See page: 
8.  Up cursor  
9.  Right cursor  
10.  Down cursor 
Navigates and changes settings in the OSD  20 
11.  Volume +/- Adjusts volume 18 
12.  Mute Mutes the built-in speaker 
13.  Zoom+ Zoom in  
14.  Zoom- Zoom out 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank Makes the screen blank 
17.  Source Detects the input device 
18.  Auto Auto adjustment for phase, tracking, size, position 
19.  Menu Opens the OSD  20 
20....

DLP® Projector – User’s Manual 
the rear of the projector, the remote will function well within a radius of about 10 meters (33 feet) and 
30 degrees above or below the projector level. If the projector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote control; however the buttons on the projector are...

 
– 10 – 
Setup and Operation 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the di-
rection of the arrow. 
 
2.  Insert the supplied batteries taking 
note of the polarity (+/-) as shown 
here. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries. (Alkaline is better) 
 
2. Dispose of used batteries according to local ordinance regulations.  
 
3. Remove the batteries when not using the projector for prolonged periods. 
 
  

DLP® Projector – User’s Manual 
Connecting Input Devices 
A PC or notebook computer as well as video devices can be connected to the projector at the same 
time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital 
still cameras. Check the user manual of the connecting device to confirm it has the appropriate output 
connector.  
 
Item Label Description 
A Rear IR Receiver for IR signal from remote control. 
B DVI-D Connect DVI-D cable (not supplied) from a...

DLP® Projector – User’s Manual 
Item Label Description 
 USB Connect the supplied USB cable (supplied) from a computer for 
USB mouse function and firmware upgrades. 
 
RS-232 Reserved for installation control. 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections. 
– 12 –