Planar Pr5022 Projector User Manual

DLP® Projector – User’s Manual 
Starting and Shutting down the Projector 
1.  Slide the lens cover. 
2.  Connect the power cord to the projector 
[A]  Connect the other end to a wall out-
let.  Switch [B] from on (O) to off ( — )   
3.  The POWER and READY LEDs on the 
projector turn on.                                         
Turn on the connected devices.  
4.  Ensure the Ready LED is on a steady 
(not flashing) orange and then press the 
Power button to turn on the projector.  
 
The projector...

DLP® Projector – User’s Manual 
7.  When the “Power Off?/Press Power 
again” message appears, press the 
Power button. The projector turns off. 
 
8.  Turn off the main Power switch when the 
Ready LED stops flashing. 
 
 
Caution: 
Do not unplug the power cord until the Ready LED stops flashing, indicating the projector has cooled 
down. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 14 –  

DLP® Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the pro-
jector. When enabled, the password must be entered after you power on the projector. (See 
“Navigating the OSD” on page 20 and “Setting the OSD Language” on page 21 for help on using 
OSD menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the...

DLP® Projector – User’s Manual 
 Every time you start the projector, a 
password dialog box appears. 
 
Enter the password in the order you 
set it at step 6. (Press the Menu 
button to cancel if you enter the wrong 
password.)  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 16 –  

DLP® Projector – User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Be sure cables are not in the way or can cause the projector to be knocked over. 
 
 
 
1.  To raise the level of the projector, lift the projector [A] and press the height-
adjuster button [B].  
The height adjuster drops down [C].  
2.  To lower the...

DLP® Projector – User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom 
control (on the projector 
only) to resize the pro-
jected image and 
screen size. B 
2.  Use the Image-focus 
control (on the projector 
only) to sharpen the 
projected image A. 
 
3.  Press the Keystone 
button on the remote 
control. 
The keystone control 
appears on the display.  
 
4.  Use the Keystone but-
ton to correct image 
distortion.  
Adjusting the Volume 
1.  Press the Volume +/- 
button on the...

DLP® Projector – User’s Manual 
3.  Press the Mute button 
to turn off the volume. 
(For remote only)  
– 19 –  

DLP® Projector – User’s Manual 
On-Screen Display (OSD) Menu Settings 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illustration shows the corresponding buttons on the re-
mote control and on the projector. 
 
                
1. To open the OSD, press the Menu button.  
2....

DLP® Projector – User’s Manual 
Setting the OSD Language 
You may want to reference the OSD on your projector while reading this section. Set the OSD lan-
guage to your preference before continuing. (The default language is English.) 
1. Press the Menu button. The Main menu appears. 
 
2. Press the cursor  button until Tool is highlighted.  
 
3. Press the cursor  button until Tool is highlighted.  
4. Press the  button until your language is displayed. 
5. Press the Menu button twice to close the OSD....

DLP® Projector – User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting.  
 
– 22 –