Home
>
RadioShack
>
Communications receiver
>
RadioShack Pro 2020 Vhf Uhf Scanner Reciever Instructions Manual
RadioShack Pro 2020 Vhf Uhf Scanner Reciever Instructions Manual
View the RadioShack Pro 2020 Vhf Uhf Scanner Reciever Instructions Manual for free. All the RadioShack manuals and user’s guides are available for free view without any registration. You can also download the manual as PDF to your computer.
![Page 1
PRO-2020 Scanner
(200-0112) Operation Faxback Doc. # 45530
Operating Your Pro-2020
Turn on your Pro-2020 by rotating [VOLUME] clockwise. (When first turned
on, your Pro-2020 may start scanning).
Rotate [SQUELCH] fully counterclockwise. Youll hear a rushing noise from
the speaker. Slowly rotate [SQUELCH] clockwise until the noise just stops.
Youre now ready to start entering frequencies.
Programming Frequencies
Before programming frequencies, make...](http://img.usermanuals.tech/thumb/5706/83773/w300_radio-shack_pro-2020-vhf-uhf-scanner-reciever_short-manual_d-0.png "Page 1
PRO-2020 Scanner
(200-0112) Operation Faxback Doc. # 45530
Operating Your Pro-2020
Turn on your Pro-2020 by rotating [VOLUME] clockwise. (When first turned
on, your Pro-2020 may start scanning).
Rotate [SQUELCH] fully counterclockwise. Youll hear a rushing noise from
the speaker. Slowly rotate [SQUELCH] clockwise until the noise just stops.
Youre now ready to start entering frequencies.
Programming Frequencies
Before programming frequencies, make...")
![Page 2
a channel. As soon as the signal ends, the scanning function will resume.
Most communications heard will be two-way. To make sure you dont miss any
replies, press [DELAY]. This will cause your Pro-2020 to stay on a channel
for two seconds after the end of a transmission, giving you time to hear
any reply. To release the Delay function, just press [DELAY] again. The
Delay indicator will show on the display when the Delay function is used.
Lockout Function
You may want your Pro-2020 to skip...](http://img.usermanuals.tech/thumb/5706/83773/w300_radio-shack_pro-2020-vhf-uhf-scanner-reciever_short-manual_d-1.png "Page 2
a channel. As soon as the signal ends, the scanning function will resume.
Most communications heard will be two-way. To make sure you dont miss any
replies, press [DELAY]. This will cause your Pro-2020 to stay on a channel
for two seconds after the end of a transmission, giving you time to hear
any reply. To release the Delay function, just press [DELAY] again. The
Delay indicator will show on the display when the Delay function is used.
Lockout Function
You may want your Pro-2020 to skip...")
![Page 3
1. Press [PROGRAM] key.
2. Press [LIMIT] key. Enter the lower limit of frequency range to be
searched (such as 45.00 MHz). Press [ENTER].
3. Press [LIMIT] key again. Enter the upper limit of frequency range to
be searched (such as 46.00 MHz). Press [ENTER].
4. Press either [up arrow] or [down arrow] to start Search. [Down arrow]
will start search from the highest frequency and go down. [Up arrow]
will start from the lowest frequency and go up.
5. You can...](http://img.usermanuals.tech/thumb/5706/83773/w300_radio-shack_pro-2020-vhf-uhf-scanner-reciever_short-manual_d-2.png "Page 3
1. Press [PROGRAM] key.
2. Press [LIMIT] key. Enter the lower limit of frequency range to be
searched (such as 45.00 MHz). Press [ENTER].
3. Press [LIMIT] key again. Enter the upper limit of frequency range to
be searched (such as 46.00 MHz). Press [ENTER].
4. Press either [up arrow] or [down arrow] to start Search. [Down arrow]
will start search from the highest frequency and go down. [Up arrow]
will start from the lowest frequency and go up.
5. You can...")
