Ricoh Projector PJ WXC1110 User Manual
Have a look at the manual Ricoh Projector PJ WXC1110 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 27
25
Remote Control Operating Range
■ When pointing the remote control directly toward the projector (Remote \
control signal
receiver), operating range for the remote control is within 3m (9.84 f\
t). Also, operation
range available for four directions (up, down, left, right to the proje\
ctor) is ± 30° and the
operation distance may become short.
■ If there are any obstacles between the remote control and the remote con\
trol signal
receiver, the remote control may not operate correctly.
■ When...](http://img.usermanuals.tech/thumb/64/100523/w64_projector_manual_9575_d-26.png "Page 27
25
Remote Control Operating Range
■ When pointing the remote control directly toward the projector (Remote \
control signal
receiver), operating range for the remote control is within 3m (9.84 f\
t). Also, operation
range available for four directions (up, down, left, right to the proje\
ctor) is ± 30° and the
operation distance may become short.
■ If there are any obstacles between the remote control and the remote con\
trol signal
receiver, the remote control may not operate correctly.
■ When...")
![Page 28
26
Connecting the Projector
To ensure the projector works well with your computer,
please make sure the timing of the display mode is
compatible with your projector. Please see page 76.
Use the cables that come with the projector.
1.........................................................................\
........................................RGB Cable2.........................................................................\
........... HDMI Cable(not supplied)...](http://img.usermanuals.tech/thumb/64/100523/w64_projector_manual_9575_d-27.png "Page 28
26
Connecting the Projector
To ensure the projector works well with your computer,
please make sure the timing of the display mode is
compatible with your projector. Please see page 76.
Use the cables that come with the projector.
1.........................................................................\
........................................RGB Cable2.........................................................................\
........... HDMI Cable(not supplied)...")
![Page 29
27
To ensure the projector works well with your computer,
please make sure the timing of the display mode is
compatible with your projector. Please see page 76.
1.........................................................................\
..........MHL Cable(not supplied)(*)2.........................................................................\
............HDMI Cable(not supplied)3.........................................................................\
...MicroSD Card(not...](http://img.usermanuals.tech/thumb/64/100523/w64_projector_manual_9575_d-28.png "Page 29
27
To ensure the projector works well with your computer,
please make sure the timing of the display mode is
compatible with your projector. Please see page 76.
1.........................................................................\
..........MHL Cable(not supplied)(*)2.........................................................................\
............HDMI Cable(not supplied)3.........................................................................\
...MicroSD Card(not...")
29 Powering Off the Projector 1. Press the “Power” to turn off the projector, you will see a message as below on the on-screen display. Power Off Power Off? Press power key again. 2. Press the “Power” again to confirm. 3. After 3~5 seconds the Power indicator will light amber. When the light starts flashing, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has entered standby mode. Once in standby mode, simply press “Power” to restart the projector. 4. Disconnect the power cord and AC adapter from the electrical outlet and the projector. English English Basic Operations English
30 Warning Indicator When the “Temp” indicator flashes amber (3 secs on, 1 sec off, ) and the message below displays on-screen, it indicates the air vents might be blocked or ambient temperature may be above 35 ° C overheated. Ensure that the air vents are not blocked and that the ambient temperature is within operating range. If the problem persists, please contact the vendor. Warning The projector will switch off automatically Over temperature Please contact a service center for repair When the “Temp” indicator flashes red (2 secs on, 0.5 sec off) and the message below displays on-screen, it indicates one of the fans has failed. The projector will automatically shut itself down. Warning The projector will switch off automatically FAN LOCKED Please contact a service center for repair When the “Error” indicator turns amber, it indicates the LED failure. The LED will shut down. In case of the fan failure, the projector shuts down automatically. Clear the projector mode by pressing and holding the Power button for 10 seconds. Please wait for about 5 minutes and try to power up again. Note English Basic Operations
31 Adjusting the Projected Image Adjusting the Height of Projector Image The projector is equipped with adjustable feet to raise and lower the image to fill the screen. To raise/lower the image: 1. Use to fine-tune the display angle. You can raise the projector front up to 7 degrees by rotating the adjustable feet. Note Front Adjustable feet 1Maximum Length: 6mm English English Basic Operations English
32 Focus Ring Adjusting the Projector Focus To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 2.82 to 5.64 feet (0.86 to 1.72 m). English Basic Operations
33 Diagonal length (inch) size of 16:10 Screen Screen Size W x HProjection Distance (D)Offset (Hd) (m)(inch)(m)(feet)(cm)WidthHeightWidthHeight 501.080.6742.5226.380.862.830 601.290.8150.7931.891.033.920 651.400.8855.1234.651.123.670 701.510.9459.4537.011.213.960 801.721.0867.7242.521.384.520 901.941.2176.3847.641.555.090 1002.151.3584.6553.151.725.650 RICOH PJ WXC1110 Adjusting Projection Image Size Width Height Diagonal Side ViewProjection Distance (D) Screen Screen (H) Offset (Hd) Projection Image Size from 50” to 100” (127.0 to 254.0 cm). English English Basic Operations English
34 The Projector has a multilingual On Screen Display that allows you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD, press the button on the Control Panel or the “Menu” button on the Remote Control. 2. To select an options, press the or buttons on the Control Panel or Remote Control. 3. To adjust settings, press the or buttons on the Control Panel or Remote Control. 4. To exit the OSD, press the button on the Control Panel or the “Menu” button on the Remote Control. On Screen Display (OSD) The projector has a multi-language on-screen display (OSD) menu that can be displayed with or without an input source. Note Input Source Menu Volume Picture Mode Brightness Contrast Image DisplaySetup Bright SelectExitEnter Sub menuSetting value or adjusting value Menu guide Menu name Computer English User Settings
35 Menu Tree Main Menu2nd Level3rd LevelRangeDefault Value Input Source Computer ComputerHDMI/MHL Media Volume0~105 Picture Mode Bright PC PC sRGB Wide 1 Wide 2 ECO Brightness0~105 Contrast0~105 Image Saturation0~2010 Hue-10~+100 Aspect Ratio Auto Auto4:3 16:9 16:10 Zoom50%/75%/100%/125%/150%/175%/200%100% Color Temperature Warm Computer => Medium HDMI => Warm Medium Cold Color Space Auto AutoRGB YCbCr Frequency-5~50 Phase0~310 English English User Settings English
36 Main Menu2nd Level3rd LevelRangeDefault Value Display Auto KeystoneOnOnOff Keystone-40~+400 Projection Auto keystone on: No reverse Left/Right reverse Auto keystone off: No reverse Left/right reverse Up/down reverse Up/down and Left/Right reverse English User Settings
37 Main Menu2nd Level3rd LevelRangeDefault Value Setup Language English English Germany French Italian Spanish Portuguese Polish Dutch Russian Swedish Greek 中文 (繁) 中文 (简) Janpanese Korean Turkish Boot-up Source Auto Computer HDMI/MHL Media Direct Power OnOnOffOff Sleep Timer Auto AutoOff 0:30 / 1:00 / 3:00 / 8:00 / 12:00 Advanced Mute Audio & Video Audio & VideoVideo Audio 3DOnOnOff 3D Sync. InvertOnOffOff SecurityGo to Security Menu ResetYesNoNo Software Ver.(displays Software Version) English English User Settings English
38 Main Menu Input Source Set the input source. Computer: Set Computer as input source. Computer SearchingComputer HDMI / MHL: Set HDMI / MHL as input source. HDMI / MHL SearchingHDMI / MHL Media: Set Media as input source. Media SearchingMedia Volume Adjust the volume. Press the to turn up the volume (up to 10) Press the to turn down the volume (minimum value 0). Input Source Menu Volume Picture Mode Brightness Contrast Image DisplaySetup Bright SelectExitEnter Computer Media Centre English User Settings