Ricoh Projector PJ WXC1110 User Manual

							39
 Picture Mode
There are factory presets optimized for various types of images.
   Bright: For displaying the maximum brightness from computer 
input.
   PC: For computer.
     sRGB: Based in sRGB.
   Wide1: Close to Adobe RGB.
   Wide2: Widest color gamut.
   Eco: For displaying in Eco mode.
The default value of Brightness, Contrast, Color Temperature, Hue, 
and Saturation depend on Picture mode.
Default value of each mode as follows.
 Brightness
 Adjust the brightness of the image. 
   Press the  to increase the brightness of the screen (up to 20).
   Press the  to reduce the brightness of the screen (minimum 
value 0).
 Contrast
   Adjust the contrast. 
    Press  the  to increase the contrast of the screen (up to 10).
   Press the  to decrease the contrast of the screen (until -10).
Picture ModeBrightnessContrastColor TempertureSatulationHue
Bright55-100
PC55Medium100
sRGB55Warm100
Wide155Warm100
Wide255Warm100
Eco55-100
English 
English
User Settings
English   
						

							40
 Image
   Go to “Image” sub menu. 
 Display
   Go to “Display” sub menu. 
 Setup
   Go to “Setup” sub menu.  
English
User Settings   
						

							41
 Saturation 
Adjust a video image from black and white to saturated color.
   Press the  to increase the intensity of the color (up to 20).
   Press the  to decrease the intensity of the color (minimum 
value 0).
 Hue 
Adjust the skin tone.
   Press the  to adjust the color to be greenish (up to 10).
   Press the  to adjust the color to be reddish (minimum value 
-10).
 Aspect Ratio
  Use this function to choose your desired aspect ratio.
   Auto: The projector displays the image by automatically 
switching the screen sizes between 4:3 and 16:9.
   4:3: Input signal is displayed to full screen. This mode is for 4:3 
aspect images.
   16:9: Input signal is displayed with 16:9 aspect in the center of 
the screen. This mode is for 16:9 aspect signals. 
   16:10: This format is for 16:10 input sources, like wide screen 
laptop.
Image
Image
Hue
Aspect Ratio
Zoom
Color Temperature
Color Space
FrequencyPhase
SelectExitEnter
Auto
Warm
Auto
Saturation
Saturation can be only adjusted in HDMI mode with supported video timings 1080p/i, 720p, and 480p/i.
Hue can be only adjusted in HDMI mode with supported video timings 1080p/i, 720p, and 480p/i.
Note
English 
English
User Settings
English   
						

							42
 Zoom
   Adjust the magnification of the image. Magnification can be set 
50%, 75%, 100%, 125%, 150%, 175%, or 200%.
 Color Temperature
   Select the color temperature. 
   Warm: The screen image looks warmer.
   Medium: The medium color temperature.
   Cold: The screen image looks colder.
  Color Space
   Select an appropriate color matrix type from “Auto”, “RGB”, \
and 
“YCbCr”. 
 Frequency
   Adjust to achieve an optimal image when there is a vertical 
flickering in the image.
 Phase
   Adjust to achieve an optimal image when there is a flickering 
image.
The “Color Temperature” function is not supported in “Bright”, “Eco”, and “3D” modes.
The “Color Space” function is supported only in HDMI mode.
The “Frequency” can be adjusted only in VGA mode.
The “Phase” can be adjusted only in VGA mode.
Note 
English
User Settings   
						

							43
 Auto Keystone
   Automatically adjust image distortion caused by tilting the 
projector.
 Keystone
   Manually adjust image distortion caused by tilting the projector.
 Projection
   Select the projection mode, depending upon how the projector is 
mounted.
   Auto Keystone: On
   -   No reverse
  -   Left/Right reverse
   Auto Keystone: Off
   -   No reverse
  -   Left/Right reverse
  -   Up/Down reverse
  -   Left/Right and Up/Down reverse
Display
Display
OnAuto Keystone
Keystone
Projection
SelectExitEnter
The “Auto Keystone” function can be only used to adjust the image distortion vertically.
If you adjust the keystone manually then the “Auto Keystone” function will be automatically disabled.
Note
English 
English
User Settings
English   
						

							44
Setup
 Language 
The language used in the On-Screen Menu is available in English, 
Germany, French, Italian, Spanish, Portuguese, Polish, Dutch, 
Russian, Swedish, Greek, Traditional Chinese, Simplified Chinese, 
Japanese, Korean, and Turkish.
 Boot-up Source
   Set the projector’s boot-up source between “Auto”, “Computer”, 
“HDMI/MHL”, and “Media”.
 Direct Power On
   When enabled, the projector will automatically power on when 
AC power is supplied, without pressing the “Power” button on 
the projector control panel or on the remote control.
 Sleep Timer
   Set the countdown timer interval between “0:30”, “1:00”, “\
3:00”, 
“8:00”, “12:00”, “Auto”, or “Off”. The countdown\
 timer will start, 
with or without a signal being sent to the projector. The projector 
will automatically power off when the countdown has finished.
 Advanced
   Go to “Advanced” sub menu.
If the “Boot-Up Source” is set to“Auto” then at each boot-up of the projector, the input source (COMPUTER, HDMI, or Media) is always chosen the same as in previous session. 
Note
If the “Sleep Timer” is set to“Auto” then the project will automatically power off after 15 minutes if the projector has not detected any signal from COMPUTER or HDMI source. 
Note
Setup
EnglishLanguage
Boot-up SourceDirect Power On
SelectExitEnter
Sleep TimerAdvanced
Reset
Software Ver.
Auto
Off
Security 
English
User Settings   
						

							45
 Security
 Go to “Security” sub menu. To change the security setting, enter 
the security code in 6 digits.
 The default password is       .(Enters with 4 directional key)
Security
Enter a password. (6 Digits)Exit
 Reset
   Return all data to the factory defaults. After choosing this option, 
a confirmation message appears on the screen. Select “Yes” to 
confirm or “No” to cancel reset.
Reset
Reset?
No Ye s
 Software Ver.
   View the current projector’s firmware version.
Note
Password is not reset by “Reset” comand.
If you fotgot the Password, please contact your dealer or service representative..
English 
English
User Settings
English   
						

							46
 Mute 
Select the “Mute” mode between “AV Mute” (mute both audio 
and video), “Audio” (mute audio only), and “Video” (mute\
 video 
only).
 3D
Use this funciton to set the display mode of the 3D image. Please 
note that this projector supports only DLP Link 3D signal. Blu-ray 
3D is not supported.
  On: Turn on “3D” image display.
  Off: Turn off “3D” image display.
 3D Sync. Invert
Flips the timing of the switch between the left and right of an 
image to display. Change the setting if the 3D images you see 
appear not as expected.
  On: Select when left and right 3D images are swapped to be 
displayed.
  Off: If the 3D images are displayed correctly, do not change the 
“Off” settings.
Advanced
The function of the “Mute” button on the remote control depends on the selected “Mute” option in the OSD menu.
“3D” and ”3D Sync. Invert” cannot be changed when you 
select image settings.
In 3D mode, the maximum supported input timing is 1024 x 768 @ 120Hz.
Note
Advanced
AV Mute
3D
3D Sync. Invert
SelectExitEnter
Off
Mute
Off 
English
User Settings   
						

							47
 Security 
Select the “Security” mode.  
  On: Use the security verification when turning on the Protector.
  Off: Disable to use security verification.
 Change Password
Change the password. Press "Enter".
  Enter New Password (6 digits): 
Use 4 directional keys to enter new password.
Enter the new password. (6 Digits)
Change Password
Exit
  Confirm New Password (6 digits): 
Enter the same password that you entered.
Change Password
Enter the password again. (6 Digits)
Exit
Security
Security
On
Change Password
SelectExitEnter
Security
Note
Do not foget the password.
Password is not reset by “Reset” comand.
If you fotgot the Password, please contact your dealer or service representative..
English 
English
User Settings
English   
						

							48
If the confirmed Password doesn not match with the entered 
Password, Input the new Password again.
By entering “Menu” key, you can cancel the “Change 
Password”menu. 
English
User Settings