Home > Roland > Printer > Roland XJ 640 User Manual

Roland XJ 640 User Manual

Here you can view all the pages of manual Roland XJ 640 User Manual. The Roland manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 41

39Chapter 2 Operation
2-5 If Ink Runs Out
Checking for Remaining Ink
Procedure
Press.
Press
several times.
Press.
Press.
Press.
Press
 to go back to the original screen.
The display shows an approximate guide to the amount of remaining ink, which may differ somewhat from the actual
amount remaining.
1          2           3           4
5          6           7           8
9        10         11         12
Amount of ink remaining
Much
Little
MENU
INK REMAINING
1          2           3           4
5...

Page 42

2-5 If Ink Runs Out
Chapter 2 Operation
40
When Ink Cartridges Become Empty
When ink runs out, a warning beep sounds and printing pauses. Then a
screen like the one shown in the figure appears (unless the default settings
have been changed). Pull out the empty cartridge and insert a new one.
Printing resumes.
Procedure
Check which cartridge is empty.
Gently shake the new cartridge.
Pull out the empty cartridge and immediately insert the
new one.
Important Notes on Replacing Cartridges
➢Be sure to...

Page 43

2-5 If Ink Runs Out
Chapter 2 Operation
41
WARNINGNever store ink, maintenance fluid, or discharged fluid in any of the following loca-
tions.
➢ Any location exposed to open flame
➢ Any location where high temperature may occur
➢ Near bleach or any other such oxidizing agent or explosive material
➢ Any location within the reach of children
Fire may be a danger. Accidental ingestion by children may pose a health hazard.
Downloaded From ManualsPrinter.com Manuals 

Page 44

42
Downloaded From ManualsPrinter.com Manuals 

Page 45

43
Chapter 3
Operation of the Media
Take-up System
Downloaded From ManualsPrinter.com Manuals 

Page 46

44Chapter 3 Operation of the Media Take-up System
3-1 The Take-up  System
Features of the Take-up System
Using the take-up system lets you perform printing while the media is taken up automatically. This makes possible
unattended operation at night and efficient printing of lengthy media.
Operating Conditions for the Take-up System
Settings Related to Media Feed
When using the take-up system, to avoid pulling media with undue force, be sure to observe the following points.
Operations that pull the media...

Page 47

45Chapter 3 Operation of the Media Take-up System
3-2 Using the Take-up System
Loading Roll Media
1.Pass the media through the printer.
Move the dancer roller toward the rear.
Load the roll media.
 P. 28, Loading Media 
Pull back the loading lever.
The media is secured in place.
2.Fasten the media to the paper tube.
When you attach the paper tube, insert it securely onto the end caps on the take-up unit. For information on how to
install it, refer to the Setup Guide.
Useto select TU.
Press.
The...

Page 48

3-2 Using the Take-up System
Chapter 3 Operation of the Media Take-up System
46
Fasten the media in place with tape at three locations (the center and both edges) so that the
media is not at an angle.
Take-up with outward curl
Take-up with inward curl
3.Make the setting for the direction of automatic take-up and perform take-up of
the media onto the paper tube.
Press.
The media is pulled out and the screen shown in the
figure appears.
Pull the dancer roller back toward you.
Fasten first.
Paper...

Page 49

3-2 Using the Take-up System
Chapter 3 Operation of the Media Take-up System
47
Make sure the media is stretched taut, and press
.
The screen shown in the figure appears.
Make the setting for the AUTO switch on the take-up unit.
Take-up with outward curl
Take-up with inward curl
	Press.
Making the setting is complete when the screen shown
in the figure (the top menu) appears.
When you begin take-up, take care to ensure that the end of the media does not become rolled or creased.
CHECK
TAKE-UP SETTING...

Page 50

3-2 Using the Take-up System
Chapter 3 Operation of the Media Take-up System
48
 

To Take up Media Manually
You can take up media by using the MANUAL switch. However, never operate the MANUAL switch while the loading
lever is pulled back. Doing so may cause the media to be pulled with excessive force, actuating the protective feature
and resulting in an error.
Removing Taken-up  Media
CAUTIONRemoval of taken-up roll media from the unit is a task which must be carried out
by two or more persons.
If...
Start reading Roland XJ 640 User Manual

Related Manuals for Roland XJ 640 User Manual

All Roland manuals