Runco Cp 52hd Installation And Operation Manual

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  17   
 
 
Installation 
 
Component Video Connections: If you have a DVD player, DTV decoder with a 
component (YPbPR) output or other component video source, connect it to the 
COMPONENT 1 or COMPONENT 2 input as shown in Figure 3-3. 
 
 
Figure 3-3. Component Video Connections 
 
Composite/S-Video Connections: The Climate Series LCD has one (1) 
Composite video input and an S-Video input for connecting a VCR, camcorder, 
laser disc player or DVD player; see Figure 3-4. 
 
If you connect an S-Video source to the Video 2 input, the Composite input on 
Video 2 is inactive. 
 
Figure 3-4. Composite and S-Video Connections 
 
 
 
 
 
 
  
						

							18                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Installation 
 
Connect the  (positive) and  (negative) speaker wires to the SPEAKER-R 
and SPEAKER-R terminals; see figure 3-5. Maintain the correct polarity. For 
more information, refer to the owner‟s manual for your speakers. 
 
Figure 3-5. External Speaker Connection 
 
Use a straight-through RS-232 cable with a 9-pin make connector to connect a PC 
or home theater control/automation system (if present) to the RS-232 port on the 
Climate Series LCD; see Figure 3-6. 
 
 
 
 
Figure 3-6. RS-232 Control System Connection. 
 
 
 
 
 
 
 
 
Connecting External 
Speakers (Optional) 
RS-232 Controller 
Connection (Optional) 
    
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  19   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							20                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
4. Operations 
 
1. Turn on your source components. 
2. Plug the female end of the supplied 
power cord into the AC receptacle inside 
the back input panel of the Climate 
Series LCD (AC 100V ~ 240 V). 
3. Connect the other end to your AC power 
source. 
4. Press the ON button (  ) on the 
remote control to turn on the display (or 
press the power button (  ) on the 
side of the display). 
5. After a brief warm-up period 
(approximately 10 seconds), the Climate 
Series LCD will display an image. 
 
 
 
 
 
 
The Climate Series LCD OSD language 
is initially set to English, but can also 
display the menus in French or Spanish. 
To change the OSD language: 
1. Press MENU. 
2. Select Setup from the Main Menu. 
3. Select Menu Language from the Setup 
Menu. 
4. Press   or  to highlight the desired 
language and press O.K. The change 
takes effect immediately. 
 
 
 
 
 
4.1 
Turning on the Power 
 
4.2 
Changing the OSD 
Language 
 
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  21   
 
 
Operations 
 
To maximize image quality when using the Climate Series LCD with a personal 
computer, you may need to adjust the display properties of your PC Video Card. 
To do this: 
1. Choose Settings from the Windows Start 
menu and click on “Control Panel.” 
 
 
 
 
 
 
2. Double click on the Display icon. 
3. Click the Settings tab on the display dialog 
box. 
4. Set the Screen area to 1400x1050 pixels. 
 
 
 
 
 
5. Click the Advanced button and click the 
Monitor tab on the dialog box. Set the 
Refresh Frequency to 60 Hz and click OK. 
 
 
 
 
 
 
 
 
 
4.3 
Setting the PC Display 
Properties 
 
    
						

							22                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Operations 
 
1. The maximum available resolution and vertical frequency is 
1920x1200/60Hz or the maximum supported by your video card, 
whichever is lower. 
2. The Climate Series LCD supports 8-bit color (16,777,216 
possible colors). 
 
Many functions are controlled through the menu function, using the remote 
control handset or keypad on the side of the display. 
To use the on-screen menus: 
1. Press MENU to display the Main Menu. 
2. To select a menu item, use the left- or right-arrow buttons ( ,) on the remote 
to control to highlight it. 
3. Press the down-arrow button () to access that menu. 
4. Use the up- or down-arrow buttons (,) to select the setting you want to 
change. Then, press the right-arrow button (). 
5. Press the right- or left-arrow button ( ,) to change that setting. 
6. To return to the previous menu, press MENU or (). 
The Climate Series LCD OSD menus are arranged hierarchically, as shown in 
Figure 4-1. Depending on the selected input source and/or signal characteristics, 
some menu options may not be available. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4.4 
Using the On-Screen 
Menus 
 
  
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  23   
 
 
Operations 
Picture 
Picture Mode 
Standard 
 
Setup 
Menu 
Language 
English 
 Dynamic 
 
French 
 Personal 
 
Spanish 
 Contrast 
0~100  
Transparency Off / On 
 Brightness 
 Zoom Mode 
Normal 
 Color 
 
Wide 
 Tint -50~+50 
 
Zoom 
 Sharpness 0~100 
 
Cinema 
 
Color Mode 
Normal 
 Noise 
Reduction 
Off 
 Warm 
 
Weak 
 Cool 
 
Middle 
 
Audio 
Sound Mode 
Standard 
 
Strong 
 Music 
 
Advanced   
 Movie 
 
Closed Caption 
CC Mode 
On 
Personal 
 
Off 
Bass 
0~100  
CC on 
mute 
Treble 
 
Basic 
Selection 
CC1 
Balance 
 
CC 
Surround Off / On 
 
Advanced 
Selection Service 1 
AVC Off / On 
 
Option 
 SPDIF Type PCM / RAW 
 
MISC Setup XVS On / Off  
 
Audio Language 
English 
 
Restore Default 
Reset to 
Factory Setup 
default 
 French 
 
Lock Enter Password   
 Spanish 
 
Channel 
Air/Cable Air / Cable 
 
Time 
Sleep Timer Off, 5 min ~ 240 
min 
 Auto Scan 
Auto 
 
Time Zone 
Pacific 
 
STD 
 Alaska 
 
IRC 
 Hawaii 
 
HRC 
 Eastern 
 
Favorite FAV channel 
 Central 
 
Show/Hide Channel On / 
Off 
 Mountain 
 
Channel No.   Daylight Savings 
Time Off / On 
 
Channel Label  
 Clock Auto 
 
DTV Signal    
Figure 4-1. Climate Series LCD OSD Menu Structure 
 
 
 
						

							24                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Operations 
Use the controls in the Picture Menu to calibrate your Climate Series LCD for 
optimum picture quality. 
Picture Mode: To set the Picture Mode, select Picture Mode from the Picture 
menu and press the left- or right- arrow buttons to select Standard, Dynamic or 
Personal. Press O.K. or MENU to confirm your selection. 
Contrast: To adjust the Contrast, select Contrast from the Picture menu and 
press the left- or right- arrow buttons to adjust. Press O.K. or MENU to confirm 
your selection. 
Brightness: To adjust the Brightness, select Brightness from the Picture menu 
and press the left- or right- arrow buttons to adjust. Press O.K. or MENU to 
confirm your selection. 
Color: To adjust the Color, select Color from the Picture menu and press the left- 
or right- arrow buttons to adjust. Press O.K. or MENU to confirm your selection. 
Tint: To adjust the Tint, select Tint from the Picture menu and press the left- or 
right- arrow buttons to adjust. Press O.K. or MENU to confirm your selection. 
Sharpness: To adjust the Sharpness, select Sharpness from the Picture menu 
and press the left- or right- arrow buttons to adjust. Press O.K. or MENU to 
confirm your selection. 
Color Mode: To set the Color Mode, select Color Mode from the Picture menu 
and press the left- or right- arrow buttons to select Normal, Warm or Cool. Press 
O.K. or MENU to confirm your selection. 
 
 
 
Picture 
   
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  25   
 
 
Operations 
To adjust the Climate Series LCD audio setting, select Audio from the Main Menu 
and press the up- or down-button to select the setting you want to change. 
Sounds Mode: To set the Sound Mode, select Sound Mode from the Audio 
menu and press the left- or right- arrow buttons to select Standard, Music, Movie 
or Personal. Press O.K. or MENU to confirm your selection. 
Bass: To adjust the Bass, select Bass from the Audio menu and press the left- or 
right- arrow buttons to adjust. Press O.K. or MENU to confirm your selection. 
Treble: To adjust the Treble, select Treble from the Audio menu and press the 
left- or right- arrow buttons to adjust. Press O.K. or MENU to confirm your 
selection. 
Balance: To adjust the left/right speaker balance, select Balance from the Audio 
Menu and press the left- or right- arrow buttons to make one channel louder than 
the other. 
Surround: To turn the Surround Sound on or off, select Surround from the Audio 
Menu and press the left- or right- arrow buttons to change setting. When finished, 
press O.K. or MENU. 
AVC: To turn the AVC on or off, select AVC from the Audio Menu and press the 
left- or right- arrow buttons to change setting. When finished, press O.K. or 
MENU to confirm your selection. 
SPDIF Type: To set the SPDIF Type, select SPDIF Type from the Audio menu 
and press the left- or right- arrow buttons to select PCM or RAW. Press O.K. or 
MENU to confirm your selection. 
Audio Language: To change the Audio Language, select Audio Language from 
the Audio menu and press the left- or right- arrow buttons to select English, 
French or Spanish. Press O.K. or MENU to confirm your selection. 
 
Audio 
   
						

							26                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Operations 
To set the Climate Series LCD Time functions, select Time from the Main Menu 
and press the up- or down-button to select the setting you want to change. 
Sleep Timer: Use the Sleep Timer to turn off the Climate Series LCD after a 
specified interval. 
To set the Sleep Timer: 
 Select Sleep Timer from the Time menu and press the left- or right- arrow 
buttons to change setting. 
-OR- 
 Press the SLEEP button on the remote control. 
Use the left- or right- arrow buttons to turn Sleep Timer off or select 5min ~ 
240min. Then, press O.K. or MENU. 
Time Zone: To set the local (North American) time zone, select Time Zone from 
the Time menu and press the left- or right- arrow buttons to select Pacific, 
Alaska, Hawaii, Eastern, Central or Mountain. Press O.K. or MENU to confirm 
your selection. 
Daylight Saving Time: To turn the Daylight Saving Time setting on or off, select 
Time Zone from the Time menu and press the left- or right- arrow buttons to 
change setting. When finished, press O.K. or MENU. 
Clock: To set the Climate Series LCD internal clock, select Clock from the Time 
menu and press ENTER. Clock should automatically update based on the digital 
channel‟s time source. When finished, press O.K. or MENU. 
 
 
 
 
Time