Runco Cp 52hd Installation And Operation Manual

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  27   
 
 
Operations 
Use the controls in the Setup menu to perform advanced image quality 
adjustments and access various other Climate Series LCD Display functions. 
Menu Language: Select Menu Language from the Setup menu and press the 
left- or right- arrow buttons to select English, French or Spanish. Press O.K. or 
MENU to confirm your selection. 
Transparency: To turn the Transparency of the Menu on or off, select 
Transparency from the Setup Menu and press the left- or right- arrow buttons to 
change setting. When finished, press O.K. or MENU. 
Zoom Mode: Select Zoom Mode from the Setup menu and press the left- or 
right- arrow buttons to select Normal, Wide, Zoom or Cinema. Press O.K. or 
MENU to confirm your selection. 
Noise Reduction: Select Noise Reduction from the Setup menu and press the 
left- or right- arrow buttons to select Off, Weak, Middle or Strong. Press O.K. or 
MENU to confirm your selection. 
Closed Caption: Select Closed Caption from the Setup menu to control the 
display of closed captions when watching programs that contain them. 
Restore Default: Restore Default setting returns your Climate Series LCD to the 
original Factory Default setting.
 
 
 
 
 
 
 
Setup 
   
						

							28                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Operations 
Use the Lock Menu to set your own password and use this password to lock your 
Climate Series LCD. Password default is set to 0000. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Lock 
   
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  29   
 
 
Operations 
 Use the controls in the Channel menu to adjust Channel settings and access 
various other Climate Series LCD Display functions. 
Air/Cable: Use the Air/Cable setting in the Channel menu to select Air or Cable. 
Auto Scan: Use the Auto Scan to select the Cable system. Press the left- or 
right- arrow buttons to select Auto, STD, IRC or HRC. 
Favorite: Select Favorite from the Channel menu to set the favorite channel 
associated with the FAV button on the Climate Series remote control. 
Show/Hide: Select the Show/Hide from the Channel menu to show or hide a 
specific channel. 
Channel No.: Allows you to tune up and down through various channels to 
select channel options. 
Channel Label: Select this Channel setting to enter customer names for 
individual channels. 
DTV Signal: Shows the format of the currently tuned channel. 
 
 
 
 
 
 
 
 
Channel 
   
						

							30                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Operations 
 
The Climate Series LCD supports Multichannel Television Sound (MTS), the 
broadcast audio standard that allows transmission of both stereo and Secondary 
Audio Program (SAP) content. 
The SAP is usually a foreign-language translation. However, it can also be used 
for other purposes such as Described Video Services (DVS0, which provide 
descriptive narration of key visual elements in programs for the benefit of the 
visually impaired. 
You can select sound options depending 
on the broadcast signal by pressing the 
MTS button on the remote control. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4.5 
Stereo Sound/SAP 
 
 
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  31   
 
 
5. Maintenance and Troubleshooting 
 
Regular cleaning will extend the life and performance of the Climate Series LCD. 
Before cleaning, be sure to unplug the power cord from the power outlet. 
Do not under any circumstances use solvents such as benzene or thinner to 
clean the Climate Series LCD. Doing so may cause deterioration or peeling of 
paint from the display or remote control unit. 
For cleaning the weatherproof protective front glass or remote control, use a mild 
household glass cleaner with a non abrasive soft cloth. If using a cleaner for the 
first time, we suggest using a test spot in a corner before cleaning the entire 
surface. 
For cleaning the body, use a mild household cleaner with a non abrasive with a 
soft cloth. If using a cleaner for the first time, we suggest using a test spot on the 
back of the TV before cleaning the entire surface. 
It is recommended that you clean the air filters located at the bottom of the 
Climate Series LCD every six (6) months. To remove the filters, simply unscrew 
the two (2) screws. Wash the filter with warm water.  Do not use chemicals of any 
sort. Allow to dry before reinstalling. 
As a general rule, use a vacuum cleaner about once a month to clean the vents 
on the rear panel of the display of dust buildup (set the vacuum cleaner to its 
weakest setting when doing this). If not removed, accumulated dust can cause 
the internal temperature to increase, resulting in possible breakdown or fire. 
 
 
Table 5-1. Troubleshooting Chart 
Symptom Possible Cause(s) Solution 
The display does not turn 
on after initial installation. 
 The Climate Series LCD is 
not plugged in or the AC 
outlet is not active. 
 
 
 The remote control battery 
has run out. 
 Ensure that the 
Climate Series 
LCD is plugged in 
and that the AC 
outlet is active. 
 Replace the 
battery. 
The display is on, but there 
is no picture. 
 Incorrect source selection. 
 
 Source component is not 
turned on. 
 Source component is 
connected incorrectly or not 
at all. 
 Select the correct 
source. 
 Turn on the source 
component. 
 Check video 
connections to the 
source component. 
 
 
5.1 
Cleaning 
 
5.2 
Troubleshooting Tips 
 
5.1 
Cleaning 
 
Cleaning the Display, 
Panel Body and Remote 
Control 
Cleaning the Air Filters 
and Vents 
   
						

							32                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Troubleshooting 
 
Table 5-1. Troubleshooting Chart (continued) 
Symptom Possible Cause(s) Solution 
Picture is okay, but there 
is no sound. 
 Audio output is muted. 
 
 
 Volume setting is too low. 
 
 Source component is 
connected incorrectly or not 
at all. 
 Speakers are connected 
incorrectly or not at all. 
 
 Audio settings are incorrect 
 Press the MUTE 
button on the 
remote control. 
 Turn up the 
volume. 
 Check audio 
connections to 
source component. 
 Check speaker 
connections 
(Figure 3-5). 
 Check the setting 
for SPDIF Type 
(page 26). For 
HDMI audio 
sources, ensure 
that the SPDIF type 
is “PCM” (refer to 
the manual for the 
source 
component). 
Image is too bright and/or 
lacks definition in the 
bright areas of the image. 
 Contrast is set too high.  Lower the contrast 
setting. 
Image appears “washed 
out” and/or dark areas 
appear too bright. 
 Brightness is set too high.  Lower the 
brightness setting. 
Colors in the image are 
swapped; for example, 
reds appear blue or vice 
versa. 
 The Red/Pr, Green/Y, or 
Blue/Pb outputs from the 
source are connected to the 
wrong inputs on the Climate 
Series LCD. 
 Ensure that the 
source outputs are 
connected to the 
correct Climate 
Series LCD input. 
The image is too large or 
too small. 
 Image size needs adjusting.  Adjust the image 
size (refer to the 
Zoom Mode on 
page 28). 
 
 
 
 
 
 
 
 
 
 
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  33   
 
 
6. Serial Communications  
 
To Interface the Climate Portfolio Series LCD with a home theater 
automation/control system or a PC running terminal emulation software (such as 
TeraTerm Open Source project at http://ttssh2.sourceforge.jp/), connect it to your 
control system or PC as shown in Figure 3-6. Use a straight-through cable. 
Configure the RS-232 controller or PC serial port as follows: no parity, 8 data 
bits, 1 stop but and no flow control. Set the baud rate to 38400 
 
 Commands are in four-byte raw HEX format in the form of Command + Data 
1 + ID + Data 2.  The Command byte is always 0x69, Data byte 1 defines 
which command is to be executed, ID byte is always 0x00; Data byte 2 is 
always 0x00, except in the case of the discrete volume command, in which 
case it is a value between 0x00 and 0x64. 
 To send a command from a PC running terminal emulation software, create 
either a separate script file for each command or a single script file 
containing all the commands along with logic to determine which command is 
to be sent.  You cannot type commands in by hand because the Climate 
Portfolio Series LCD expects the bytes to be sent faster than a human can 
type, and also many of the HEX values for Data byte 1 are outside the range 
one can enter using the keys on a keyboard. 
 When you send a valid command, the Climate Portfolio Series LCD executes 
it and acknowledges it with “OK” (0x4F followed by 0x4B).  Depending upon 
the command, it may also return additional strings having to do with 
execution of that command. 
 When you send an invalid or unrecognized command the Climate Portfolio 
Series LCD ignores it and returns “NG” (0x4E followed by 0x47). 
 
Table 6-1 lists the RS-232 command set. 
 
Table 6-1. Serial Commands 
COMMAND DATA 1 ID DATA 2 
0X69 0X90 : SOURCE  0x00  0X00  
 0X91 : SLEEP  0x00  0X00  
 0X92 : 1  0x00  0X00  
 0X93 : 4  0x00  0X00  
 0X94 : 7  0x00  0X00  
 0X95 : 0  0x00  0X00  
 0X96 : ENTER  0x00  0X00  
 
6.1 
RS-232 Connection 
and Port 
Configuration 
6.2 
Serial Command 
Syntax 
 
						

							34                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
Serial Communications 
 
Table 6-1. Serial Commands (continued) 
COMMAND DATA 1 ID DATA 2 
 0X97 : MENU  0x00  0X00  
 0X98 : CHRTN  0x00  0X00  
 0XA1 : DISPLAY  0x00  0X00  
 0XA2 : 2  0x00  0X00  
 0XA3 : 5  0x00  0X00  
 0XA4 : 8  0x00  0X00  
 0XA5 : . (DOT)  0x00  0X00  
 0XA7 : LEFT  0x00  0X00  
 0XB1 : MTS  0x00  0X00  
 0XB2 : 3  0x00  0X00  
 0XB3 : 6  0x00  0X00  
 0XB4 : 9  0x00  0X00  
 0XB5 : CC  0x00  0X00  
 0XB6 : ASPECT  0x00  0X00  
 0XB7 : RIGHT  0x00  0X00  
 0XC0 : MUTE OFF  0x00  0X00  
 0XC1 : MUTE ON  0x00  0X00  
 0XC2 : VOL+  0x00  0X00  
 0XC3 : VOL-  0x00  0X00  
 0XC4 : CH+  0x00  0X00  
 0XC5 : CH-  0x00  0X00  
 0XC6 : PICTURE  0x00  0X00  
 0XC7 : DOWN  0x00  0X00  
 0XD0 : POWER OFF  0x00  0X00  
 0XD1 : POWER ON  0x00  0X00  
 0XD2 : FAV  0x00  0X00  
 0XD3 : SOUND  0x00  0X00  
 0XD5 : EPG  0x00  0X00  
 0XD6 : EXIT  0x00  0X00  
 0XD7 : UP  0x00  0X00  
 0XD8 : AUTO  0x00  0X00  
 0XC9 : COMPONENT 1,2  0x00  0X00  
 0XCA : HDMI 1,2  0x00  0X00  
 OXCB : COMPOSITE  0x00  0X00  
 0XCC : TV  0x00  0X00  
 
 
						

							            Runco CP-42HD/CP-52HD Owner’s Operating Manual  35   
 
 
Serial Communications 
 
Table 6-1. Serial Commands (continued) 
COMMAND DATA 1 ID DATA 2 
 0XCD : S-VIDEO  0x00  0X00  
 0XBA : DIGITAL  0x00  0X00  
 0XDA : VGA  0x00  0X00  
 0X60 : CLEAR EEPROM  0x00  0X00  
 0X61 : DIRECTLY CONTROL VOLUME 0x00 0x00-0x64 
 0X64 : BLACKLIGHT OFF 0x00 0X00 
 0X65 : BLACKLIGHT ON 0x00 0X00 
 0X67 : HDMI 1 0x00 0X00 
 0X68 : HDMI 2 0x00 0X00 
 0X69 : COMPONENT 1 0x00 0X00 
 0X6A : COMPONENT 2 0x00 0X00 
 
Example code fragment from a TeraTerm v4.66 script: 
 inputbox Enter Command  Command 
 
 strcompare inputstr power off 
 if result == 0 then 
  send $69 $D0 $00 $00 
 endif 
 
 strcompare inputstr power on 
 if result == 0 then 
  send $69 $D1 $00 $00 
 endif 
 
 strcompare inputstr hdmi1 
 if result == 0 then 
  send $69 $67 $00 $00 
 endif 
 
 
 
 
 
 
 
 
						

							36                      Runco CP-42HD/CP-52HD Owner’s Operating Manual 
 
 
7. Specifications  
 
Table 7-1 lists the Climate Series LCD specifications. 
 
Table 7-1. Climate Series LCD Specifications 
 
Native Resolution: 1920 x 1080 (full high definition) 
Screen Size: 
CP-42HD = 42 in. (diagonal) 
CP-52HD = 52 in. (diagonal) 
Screen Aspect Ratio: 16:9 
Available Aspect Ratios: 4:3, Letterbox, 16:9, Anamorphic 
DTV Compatibility: 480i, 480p, 720p, 1080i, 1080p 
Contrast Ratio: 2,000:1 
Data/Graphics 
Compatibility: Up to 1920x1200 at 60 Hz 
Response Time (typical): 
CP-42HD = 6.5 ms 
CP-52HD = 6 ms 
Vivix Processing: 
RTR™: Real Time Refresh 60Hz panel and 
processing, Vivix 3:2 pull down 
Video/Audio Inputs: 
(1) Composite, (1) S-video, (2) component, (2)HDMI, 
(1) VGA (15-pin D-sub) 
Outputs: 
(1) Digital Audio RCA, (1) Speakers out (amplifier 
recommended) 
Discrete IR Control: 
Source, power and aspect ratios via RS-232 or 
remote 
Power Requirements: AC 100~240V 50~60Hz 5A max 
Power Consumption 
(typical): 
CP-42HD = 350W 
CP-52HD = 500W 
Operating Environment: Operation temperature 0 degrees C to 40 degree C.  
Dimensions (w/o stand): 
CP-42HD = 40.9 (1,040mm) x 4.6 (116.5mm) x 
25.2 (640mm) 
CP-52HD = 50.4 (1,280mm) x 5.3 (135mm) x 
30.5 (775mm) 
Weight (w/o stand): 
CP-42HD = 73.1 lbs (33.2 Kg) 
CP-52HD = 121 Lbs (55 Kg) 
Limited Warranty: 
(1) One year RuncoCare parts and labor from the 
date of delivery to the end user. RuncoCare™ and 
Runco RedCarpet™ plans are also available. 
Specifications are subject to change without notice. 
 
 
 
 
 
7.1 
Climate Series LCD 
Specifications