Runco V 50hd Installation And Operation Manual
Have a look at the manual Runco V 50hd Installation And Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation Vistage™ Series Flat-Panel Display Installation/Operation Manual 17 PREL IMINARY 3.4 Connections to the V-50HD/V-63HD and DHD ControllerProceed as follows to connect the DHD Controller to the V-50HD/V-63HD, your video sources, external controller(s) – if present – and AC power. To access the rear-panel connectors, use a Phillips screwdriver to loosen the screws securing the protective cover plates (see Figure 2-3) to the panel, then remove the plates. When connecting your equipment: Turn off all equipment before making any connections. Use the correct signal cables for each source. For best performance and to minimize cable clutter, use high-quality cables that are only as long as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will suffice.) Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connecting the DHD Controller to the V-50HD/V-63HD Connect the HDMI Out To Display connector on the DHD Controller to the PRIMARY INPUT connector on the V-50HD/V-63HD. See Figure 3-2. Then, re-attach the input cover plate, routing the cable through the nearest slot on the plate. Figure 3-2. Connecting the V-50HD/V-63HD to the DHD Controller Use an HDMI cable for this connection. A DVI cable with DVI-to-HDMI adapters will not work. Caution SECONDARY INPUTSERVICE PORTPRIMARY INPUT Video 1 Y Video 2 Video 3 Pr PbRS-232 HDMI 2 HDMI 4EthernetHDMI Out To Display HDMI Out Audio OnlyPr R Pb B Y G HD1 HD2 HV RS-232deo1YVVideo1ideo 2 Video3PrPbHDMI2HDMI4EthernetHDMI OutAudio OnlyPrRPbBYG HD1 HD2HV HDMI Out To Display PRIMARY INPUT
Installation 18 Vistage™ Series Flat-Panel Display Installation/Operation Manual PREL IMINARY Connecting Source Components to the DHD ControllerConnect your video sources to the DHD Controller as shown and described in the sections that follow. HDMI Source Connections: See Figure 3-3. Figure 3-3. HDMI Source Connections➤ Use the HDMI inputs whenever possible. Not only does this ensure the best possible picture quality, it provides a communication channel for CEC command messages between the display and source component (if both support CEC). You can also connect computers with DVI output to these inputs. Refer to Supported Timings on page 75 for a list of compatible input signals. Tip Note Video 2 Video 3RS-232 HDMI 1HDMI 3 HDMI 2 HDMI 4EthernetHDMI Out To Display HDMI Out Audio OnlyVideo2 Video3 RS-232 Ethernet HDMI OutTo DisplayHDMI OutAudio Only HDMI AV OUT HDMI AV OUT HDMI AV OUT HDMI sources (BD, DVD, DTV Set-Top Box etc.) HDMI AV OUT
Installation Vistage™ Series Flat-Panel Display Installation/Operation Manual 19 PREL IMINARY Component Video Source Connections: Connect your component video sources to the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-4. Figure 3-4. Component Video Source Connections Video 1 Y Video 2 Video 3 Pr Pb Pr R Pb B Y GHD1 HD2 HV Y PBPR COMPONEN T VIDEO OUT BD/DVD DTV-Set-Top Box (DTV-STB) RCA-to-BNC adapter
Installation 20 Vistage™ Series Flat-Panel Display Installation/Operation Manual PREL IMINARY RGBHV Source Connections: Connect personal computers and/or other RGB sources to the HD1 and/or HD2 inputs as shown in Figure 3-5. Figure 3-5. RGBHV Source Connections Pr R Pb B Y G HD1 HD2 HV or ComputerRGB Camcorder Green Blue Red H-Sync V-Sync
Installation Vistage™ Series Flat-Panel Display Installation/Operation Manual 21 PREL IMINARY SCART RGBS Source Connections: Connect the green, blue and red outputs from your SCART source to the Component/SCART input on the DHD Controller. Connect the sync output from your SCART source to the Video 1 input on the DHD Controller. See Figure 3-6. Figure 3-6. SCART RGBS Source Connection Composite Source Connections: See Figure 3-7. Figure 3-7. Composite Video Source Connections Video 1 Y Video 2 Video 3 Pr Pb Pr R Pb B Y GHD1 HD2 HVPrRPbBYG HD1 HD2HV Gaming ConsoleVCR DVD/DTV STB SCART-to-RGBS adapter Green Blue Red Sync Green Blue Red Sync Video 1 Y Video 2 Video 3 Pr PbHDMI 1 HDMI 2 Pr R Pb B Y GHD1 HD2 HV Y PrPbPrRPbBYG HD1 HD2HV HDMI1 HDMI2 Gaming ConsoleVCR Camcorder Composite Composite Composite Composite Composite Composite
Installation 22 Vistage™ Series Flat-Panel Display Installation/Operation Manual PREL IMINARY Connecting an Audio Processor or Secondary Display Device to the DHD Controller (Optional)The DHD Controller provides a second HDMI output (labeled HDMI Out (Audio Only)) for connection to an audio receiver/switching system or secondary display device for monitoring purposes. See Figure 3-8. Figure 3-8. Audio Processor Connection to DHD Controller➤ The DHD Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector. For more information about CEC, refer to Using HDMI CEC Messages on page 68. Note Video 1 YVideo 2 Video 3 Pr PbRS-232 HDMI 1HDMI 3 HDMI 2 HDMI 4EthernetHDMI Out To Display HDMI Out Audio Only 1 2 deo1YVVideo 1ideo2 Video 3PrPb RS-232HDMI 1HDMI 3 HDMI 2HDMI 4Ethernet HDMI OutToDisplay 1 2 or Audio Processor/ SwitcherSecondary Display
Installation Vistage™ Series Flat-Panel Display Installation/Operation Manual 23 PREL IMINARY RS-232 Controller Connection Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation system (if present) to the RS-232 port on the DHD Controller; see Figure 3-9. For more information about using this connection, refer to External Control on page 59. Figure 3-9. RS-232 Control System Connection Ethernet Network Connection Use a standard, Category 5 network cable with an RJ-45 plug to connect a network hub, router or gateway to the Ethernet port on the Primary DHD Controller; see Figure 3-10. For more information about configuring and using this connection, refer to Network on page 48. Figure 3-10. Ethernet Network Connection to Primary DHD Controller PC / ControlRS-232 HDMI 3 HDMI 4Ethernet HDMI Out To Display HDMI Out Audio Only HDMI 3 HDMI4Ethernet HDMI OutTo Display HDMI OutAudio Only 12345 7896 to Automation/ Control System or PC2 Receive Data 3 Transmit Data 5 Ground (none of the other pins are used) RS-232 HDMI 3 HDMI 4EthernetHDMI Out To Display HDMI Out Audio OnlyRS-232HDMI 3 HDMI 4 HDMI OutToDisplay HDMI OutAudio Only 1 8 to Ethernet Hub, Router or Gateway 1 Transmit Data + 2 Transmit Data - 3 Receive Data + 6 Receive Data -
Installation 24 Vistage™ Series Flat-Panel Display Installation/Operation Manual PREL IMINARY Connecting to AC PowerThe V-50HD/V-63HD ships with two (2), AC power cords: one for the DHD Controller and one for the display. 1. Plug the female end of one of the power cords into the AC receptacle on the rear of the V-50HD/V-63HD (AC 100V ~ 240V); see Figure 2-3. 2. Connect the other end to your AC power source. 3. Re-attach the AC input cover plate, routing the power cord through the slot on the plate. 4. Connect the DHD Controller to a nearby AC outlet using the other AC power cord. 3.5 Turning on the Power1. Power up your source components. 2. Press the ON button on the remote control to turn on the system. The front-panel status indicator on the DHD Controller flashes blue to indicate that it is powering up. 3. When the display is ready for use, the front-panel status indicator on the DHD Controller lights solid blue. ➤
Operation Vistage™ Series Flat-Panel Display Installation/Operation Manual 25 PREL IMINARY 4.1 Setting the Computer Display PropertiesTo maximize image quality when using the V-50HD/V-63HD with a personal computer, you may need to adjust the display properties of your computer’s video card. To do this on a Microsoft® Windows®-based PC: 1. Choose Settings from the Windows Start Menu and click on “Control Panel.” 2. Double click on the Display icon. 3. Click the Settings tab on the display dialog box. 4. Set the Screen area to 1024x768 pixels. 4. Operation
Operation 26 Vistage™ Series Flat-Panel Display Installation/Operation Manual PREL IMINARY 5. Click the Advanced button and click the Monitor tab on the dialog box. Set the Refresh Frequency to 60Hz and click OK. 1. The native resolution of the V-50HD/V-63HD is 1920 x 1080. Other horizontal or vertical resolutions may be scaled upward or downward to fit the display. 2. With most computers, you can get the best picture at 1024 x 768 @ 60Hz. To prevent image retention (burn) on your display, ALWAYS use a screen saver and set it to the shortest possible time. Note WARNING