Samsung CLP 660N User Manual

							
6.4   
2 Grasp the handles on the toner cartridge and pull to remove the 
cartridge from the machine.
Caution
If you open the front door, be careful not to touch the 
underneath of the control panel (the lower part of the fuser unit). 
The temperature of the fuser unit might be high and could 
damage your skin.
Note
When you open the front door and wo rk inside the machine, it is 
highly recommend that you remove the paper transfer belt first. 
Because the work you do could contaminate the paper transfer 
belt.
3 Holding both handles on the toner cartridge, thoroughly rock it from 
side to side to redistribute the toner.
Note
If toner gets on your clot hing, wipe it off with a dry
cloth and wash it in cold water. Hot water sets toner into
fabric.
4 Slide the toner cartridge back into the machine.
5 Close the front cover. Make sure the cover is securely latched.
Caution
If the front cover is not completely closed, the machine will not 
operate.
Replacing the toner cartridge
The machine uses four colors and has  a different toner cartridge for each 
one: yellow (Y), magenta (M), cyan (C), and black (K).
• The status LED and the toner-relate d message on the display indicate 
which individual toner cartridge should be replaced.
At this stage, the toner cartridge n eeds to be replaced. Check the type of 
toner cartridge for your machi ne. (See Supplies on page 8.1.)
1 Turn the machine off, then wait a few minutes for the machine to 
cool.
2 Using the handle, completely open the front cover.
 
Caution
• Do not touch the green surface,  the OPC drum or the front of 
each toner cartridge, with your hands or any other material. 
Use the handle on each cartridge in order to avoid touching 
this area.
• Be careful not to scratch the surface of the paper transfer  belt.
• If you leave the front cover open for more than a few minutes,  the OPC drum can be exposed to light. This will cause 
damage to the OPC drum. Close the front cover should the 
installation need to be halted for any reason.
Downloaded From ManualsPrinter.com Manuals 
						

							
6.5   
3 Grasp the handles on the empty toner cartridge and pull to remove 
the cartridge from the machine.
Caution
If you open the front door, be careful not to touch the 
underneath of the control panel (the lower part of the fuser unit). 
The temperature of the fuser unit might be high and could 
damage your skin.
Note
When you open the front door and wo rk inside the machine, it is 
highly recommend that you remove the paper transfer belt first. 
Because the work you do could contaminate the paper transfer 
belt.
4 Take a new toner cartridge out of its package.
Caution
• Dont use sharp objects, such as a knife or scissors, to open 
the toner cartridge package. Y ou could damage the surface of 
the toner cartridge.
• To prevent damage, do not expose the toner cartridge to light  for more than a few minutes. Cover it with a piece of paper to 
protect it if necessary.
5 Holding both handles on the toner cartridge, thoroughly rock it from 
side to side to evenly distribute the toner. 
6 Place the toner cartridge on a flat  surface, as shown, and remove 
the paper covering the toner cartridge by removing the tape.
Note
If toner gets on your clothing,  wipe it off with a dry cloth and 
wash it in cold water. Hot water sets toner into fabric.
7 Make sure the color of the toner cartridge matches the color slot and 
then grasp the handles on the toner cartridge. Insert the cartridge 
until it clicks into place.
8 Close the front cover. Make sure the cover is securely latched, and 
then turn the machine on.
Caution
If the front cover is not completely closed, the machine will not 
operate.
Downloaded From ManualsPrinter.com Manuals 
						

							
6.6   
Replacing the paper transfer belt
The life of the paper tran sfer belt is approximately 50,000 black and color 
pages. After the life span of the paper transfer belt is complete, you have 
to replace it.
• The transfer belt-related message appears on the display, telling its  time for a replacement.
• The SmartPanel program window appears on the computer telling you  the paper transfer belt needs to be replaced.
Note
The life span of the paper transfer belt may be affected by 
operating environment, printing interval, media type, and media 
size.
1 Turn the machine off, then wait  a few minutes for the machine to 
cool.
2 Using the handle, completely open the front cover.
Caution
Be careful not to scratch the surface of the paper transfer belt.
3Press the green release handle to release the paper transfer belt. 
Holding the handle on the paper transfer belt, lift it out of the 
machine.
4 Take a new paper transfer belt out of its package.
Caution
• Dont use sharp objects, such as a knife or scissors, to open 
the paper transfer belt package. You could damage the 
surface of the paper transfer belt.
• Be careful not to scratch the surface of the paper transfer  belt.
5 Holding the handle on the new paper transfer belt, align it with the 
slots on the inside of the front cover.
Downloaded From ManualsPrinter.com Manuals 
						

							
6.7   
6 Lower the paper transfer belt until it is parallel with the front cover 
and firmly seated. 
7 Close the front cover firmly.
Caution
If the front cover is not completely closed, the machine will not 
operate.
8 Turn the machine on.
Maintenance parts
To avoid print quality and paper feed problems resulting from worn parts, 
and to maintain your machine in top working condition, the following items 
will need to be replaced after the specified number of pages, or when the 
life span of each item has expired. 
We highly recommend that this  maintenance be performed by an 
authorized service provider, dealer  or the retailer where you bought the 
machine. The warranty does not  cover the replacement of the 
maintenance parts after their lifespan.
Managing your machine from the website
If you have connected your machine to a network and set up TCP/IP 
network parameters correctly, you can manage the machine via 
Samsung’s  SyncThru™ Web Service , an embedded web server. Use 
SyncThru™ Web Service  to:
• View the device information  and check its current status.
• Change TCP/IP parameters and set up other network parameters.
• Change the printer properties.
• Set the machine to send email not ifications and update you on the 
machine’s status.
• Get support for using the machine.
To access  SyncThru™ Web Service :
1 Start a web browser, such as Internet Explorer, from Windows.
2 Enter the machine IP address (htt p://xxx.xxx.xxx.xxx) in the address 
field and press the  Enter key or click 
Go.
Your machine’s embedded website opens.
ItemsYield (Average)
Multi-purpose tray friction 
pad  Approximately 70,000 pages 
Multi-purpose tray pick up 
roller Approximately 70,000 pages
Fuser unit  Approximately 100,000 pages
Paper pick up roller Appro ximately 70,000 pages
FCF friction pad Approximately 70,000 pages
Downloaded From ManualsPrinter.com Manuals 
						

							
7.1   
7 Troubleshooting
This chapter gives helpful information on what to do if you encounter a 
problem.
This chapter includes:
• Tips for avoiding paper jams
• Clearing paper jams
• Understanding display messages
• Solving other problems
Tips for avoiding paper jams
By selecting the correct media types,  most paper jams can be avoided. 
When a paper jam occurs, follow the steps outlined on page 7.1. 
• Follow the procedures on page 4.4.  Ensure that the adjustable guides 
are positioned correctly.
• Do not overload the tray. Ensure that the paper level is below the  paper capacity mark on the inside of the tray.
• Do not remove paper from the tray while your machine is printing.
• Flex, fan, and straighten  paper before loading. 
• Do not use creased, damp, or highly curled paper.
• Do not mix paper types in a tray.
• Use only recommended print media. (
See Setting the paper size and 
type on page 4.7.
)
Clearing paper jams
When a paper jam occurs, the warning message appears on the display 
screen. Refer to the table below to locate and clear the paper jam.
MessageLocation of jamGo to
MP Tray 
Paper Jam 0 In the multi-purpose tray Page 7.3
Tray 2 
Paper Jam 0 In the optional tray Page 7.6
Paper Jam 0
Open/Close Door In the paper feed area and 
inside the machine Page 7.1, 
Page 7.4
Paper Jam 1
Open/Close Door Inside the machine Page 7.1, 
Page 7.4
Paper Jam 2
Check Inside Inside the machine and in the 
exit area Page 7.1, 
Page 7.5
Duplex Jam 0
Check Inside* Inside the machine Page 7.1
Note
The symbol * denotes an optional feature depending on 
machines.
Caution
To avoid tearing the paper, pull the jammed paper out gently 
and slowly. Follow the instructions in the following sections to 
clear the jam. 
In the paper feed area 
If paper is jammed in the paper feed area, follow the next steps to release 
the jammed paper. 
1
Using the handle, completely open the front cover. 
2 Carefully remove the paper by pulling in the direction as shown 
below. Go to step 7.
If you cannot find the jammed paper , or if there is any resistance 
removing the paper, stop pulling, and go to step 3.
Downloaded From ManualsPrinter.com Manuals 
						

							
7.2   
Caution
• Do not touch the green surface,  the OPC drum or the front of 
each toner cartridge, with your  hands or any other material. 
Use the handle on each cartridge in order to avoid touching 
this area.
• Be careful not to scratch the surface of the paper transfer  belt.
• If you leave the front cover open for more than a few minutes,  the OPC drum can be exposed to light. This will cause 
damage to the OPC drum. Close the front cover should the 
installation need to be halted for any reason.
3 Close the front cover.
4 Pull the tray open. 
5 Remove the jammed paper by gently pulling it straight out as shown 
below.
6To replace the tray, lower the rear edge, align it with the slot, and 
slide it into the machine.
 
7Open the front cover and close it. The machine will resume printing.
Downloaded From ManualsPrinter.com Manuals 
						

							
7.3   
In the multi-purpose tray
When you print using the multi-purpose  tray and the machine detects that 
there is either no paper or that  the paper has been improperly loaded, 
follow the next steps to release the jammed paper.
1 Check if the paper is stuck in the  feeding area, and if so, pull it out 
gently and slowly.
If you cannot find the jammed paper, or if there is any resistance 
removing the paper, stop pulling and go to step 2.
2 Close the multi-purpose tray.
3 Pull the tray1 out.
4 Open the inner cover while you are releasing the inner cover locks 
on each side of tray1 with two hands.
5Pull the paper out gently.
6 Close the inner cover.
7 Replace the tray.
If you cannot find the jammed paper , or if there is any resistance 
removing the paper, stop pulling and go to step 8.
8 Using the handle, completely open the front cover.
Downloaded From ManualsPrinter.com Manuals 
						

							
7.4   
9 Remove the jammed paper by pulling in the direction shown. To 
avoid tearing the paper, pull it out gently and slowly.
Caution
• Do not touch the green surface,  the OPC drum or the front of 
each toner cartridge, with your  hands or any other material. 
Use the handle on each cartridge in order to avoid touching 
this area.
• Be careful not to scratch the surface of the paper transfer  belt.
• If you leave the front cover open for more than a few minutes,  the OPC drum can be exposed to light. This will cause 
damage to the OPC drum. Close the front cover should the 
installation need to be halted for any reason.
10 Close the front cover firmly. The machine will resume printing.
Caution
If the front cover is not completely closed, the machine will not 
operate.
In the fuser unit area
If paper is jammed in the fuser unit area, follow the next steps to release 
the jammed paper.
1Open the top cover.
2 Open the inner cover using the handle on it. 
Caution
Do not touch the fuser inside the  inner cover. It is hot and could 
cause burns! The fusers operating temperature is 180
°C 
(356
°F). Take care when removing paper from the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							
7.5   
3 Pull up the paper jam lever to release the fusing part of the fuser unit 
and carefully take the jammed paper out of the machine.
4 Press down the paper jam lever to fasten the fusing part.
5 Close the inner cover.
6 After removing the jammed paper, check for paper which may be 
jammed in other parts of the machine.
7 Close the top cover. Make sure  that it is securely latched.
Caution
If the top cover is not completely closed, the machine will not 
operate.
In the paper exit area
If paper is jammed in the paper exit area, follow the next steps to release 
the jammed paper.
1If a long portion of the paper is  visible, pull it straight out. 
Open and close the front cover firmly. The machine will resume 
printing.
If you cannot find the jammed paper, or if there is any resistance 
removing the paper, stop pulling and go to step 2.
2 Open the top cover.
3 Open the inner cover using the handle on it. 
Caution
Do not touch the fuser inside the  inner cover. It is hot and could 
cause burns! The fusers operating temperature is 180
°C 
(356
°F). Take care when removing paper from the machine.
4 Pull up the paper jam lever to loose the fusing part of the fuser unit 
and carefully take the jammed paper out of the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							
7.6   
5 Press down the paper jam lever to fasten the fusing part.
6 Close the inner cover.
7 After removing the jammed paper, check for paper which may be 
jammed in other parts of the machine.
8 Close the top cover. Make sure  that it is securely latched.
Caution
If the top cover is not completely closed, the machine will not 
operate.
In the optional tray
If paper is jammed in the optional tray, follow the next steps to release the 
jammed paper.
1Pull the optional tray open. After you  pull it all the way out, lift up the 
front part of the tray slightly to  release the tray from the machine.
2If you see the jammed paper, remove the paper from the machine 
by gently pulling it straight out as shown below.
3 Slide the tray back into the machine and close the two jam covers. 
4 Open the front cover. 
Downloaded From ManualsPrinter.com Manuals