Samsung Dcs 400si Falcon Keyset User Guide

ANSWERING THE DOOR PHONEWhen you are programmed to receive calls from a door phone:
• You will receive three short rings repeated.
• Lift the handset or press ANS/RLS key. You are connected to the door
phone.
• If an electric door lock release is installed, dial 13to unlock the door.CALLING THE DOOR PHONE/ROOM
MONITORYou may call the door phone and listen to what may be happening outside
or in another room.
• Dial the extension number of the door phone.
• You will be connected to the door phone and you...

• While on-hook, press TRANSFERand then dial 100.
• Dial your four digit station passcode.
• Dial 1to locking outgoing, 2for locked all calls, or 0to unlock.
• Press TRANSFERto store your selection.
NOTE:  When your keyset is locked for outgoing, the HOLDkey will flash.
When your keyset is locked for all calls, the HOLDkey will light 
steady.MANUAL SIGNALLINGUse this feature when you want to send a brief 500ms ring burst to another
station, regardless of the status of your phone (on-hook, off-hook,...

• Press the flashing CALLbutton on your keyset. This will place the orig-
inal party on hold and allow you to talk to the announcing party.
• To return to your first party, press the key corresponding to your original
call. This will disconnect the OHVA call.
If your keyset is associated with a DCS 32 Button Add-On Module, you can
receive Executive OHVA calls. Executive Off-Hook Voice Announce allows
you to engage in conversation on your keyset and simultaneously receive
and reply handsfree to an OHVA...

• Redial the new passcode to verify. If successful, you will hear two beeps.
Four beeps indicate an incorrect code. Reenter the code again.
• Press TRANSFERto store the new passcode.SET ANSWER MODEYou can receive internal calls in one of three modes (see Answering Intercom
Callsunder Intercom Callsfor descriptions):
• While on-hook, press TRANSFERand then dial 103.
• Dial 0for Ringing, 1for Auto Answer or 2for Voice Announce.
• Press TRANSFERto store your selection.
NOTE: When your keyset is programmed...

43
DISPLAY FEATURES
INTERACTIVE DISPLAY KEYSThe three keys below the display are substitutes for dedicated feature keys
and access codes. Pressing one of these keys has the same effect as press-
ing a programmable key. These keys are called soft keys as their functions
are not fixed. They change to present you with the best options for that call
condition. The use of soft keys allows the programmable keys to be used for
more DSSand speed dial keys.
The SCROLLkey is used to display options available to...

CALL DURATION TIMERThe system can be set to automatically time outside calls. A few seconds
after you dial a telephone number, the timer appears in the display. It
appears immediately for incoming calls. The call timer continues for the du-
ration of the call. Call duration times are displayed in minutes and seconds.
If a call lasts longer than 60 minutes, the timer restarts.
You can press the TIMERkey to manually begin timing a call. Press it again
to stop timing. If you press it while the automatic...

PERSONAL SPEED DIAL NAMESEach personal speed dial number can have an 11 character name assigned
to it. This name is used to select the speed dial bin when you are dialing by
directory. 
• Press TRANSFERand then dial 106.
• Dial the speed dial bin number 00–49.
• Write your message using the procedure described in Alarm Reminder
Messages.
• Press the TRANSFERkey to store the speed dial name.
• Repeat for each speed dial bin if necessary.STATION NAMESYou can assign an 11 character name to your keyset. This...

INVALID CID INFO This is a message that will be displayed when CID infor-
mation is sent on the line but was somehow corrupted.
NO  CID  RECEIVED This is a message that will be displayed when there was
no CID information sent on the line.
NO CID DSP Caller ID Digital Signal Processors (CIDDSP’s) are
resources in the DCS 400si required for receiving CID
data. If there are no CIDDSP’s available at the time a
call comes in, this is the message you will see on your
display.
NOTE: The Caller ID features...

INQUIRE CID/ANI PARK/HOLD INFOIf you are informed that an incoming call is on hold or has been parked for
you, you may view the Caller ID information before you retrieve the call. This
may influence how you choose to handle the call.
From an idle keyset:
• Press the INQUIREkey, OR
Press the CIDkey and then the INQUIREsoft key.
• Dial the trunk number.
• You may now answer the call by pressing the ANS key, OR
You may use NNDto view more information about this call, OR
You can return to the idle condition...

Press SCROLLand then press STOREto save this number in a person-
al speed dial bin.
NOTES: 
1. Each keyset defaults with ten review bins. Please see your system ad-
ministrator to determine the number of bins assigned to your keyset.
2. Your system must have LCR correctly programmed to allow you to DIAL
numbers from the review list or to STOREentries from the review list.
LCR WITH CLEARWhen you are making an outside call using LCR and dial an incorrect digit,
you can press the CLEARsoft key to reenter...