Samsung HL-S6767W Dlp Tv Owners Instructions

							English - 11
Right Side Buttons
The buttons on the right side panel control your TV’s basic features, including the on-screen menu system.
To use the more advanced features, you must use the remote control.
The product color and shape may vary depending on the model.
Press to switch between viewing TV programs and signals from connected components.
Press to see the on-screen menu.
Press to raise or lower the volume and to select items when using the on-screen menu.
Press to change channels and move between items on the on-screen menu.
Press to activate (or change) a particular item.
Side Panel Jacks
Use the right side panel jacks to connect a component that is used only occasionally (a camcorder or
video game, for example).
The product color and shape may vary depending on the model.
Connect the video signal from a camcorder or video game.
Connect the audio signal from a camcorder or video game.
Connect an S-Video signal from a camcorder or video game.
(S-Video 3 jack and Audio L/R input 3 are used in conjunction.)
BP68-00588G-01Eng(002~015)  5/12/06  5:55 PM  Page 11 
						

							Your New Wide TV
English - 12
Rear Panel Jacks
ŒVIDEO/AUDIO INPUT jacks Connect video/audio signals from external sources, such as VCR
or DVD players. (Refer to pages 19, 22, and 24)
´
S-VIDEO INPUT jacksConnects an S-Video signal from an S-VHS VCR or DVD player. 
(Refer to pages 19, and 24)
ˇ
VIDEO/AUDIO OUTPUT jacks  Sends video/audio signals from the TV to an external source,
such as a VCR. These jacks are available only in TV, Video and 
S-Video modes. (Refer to page 24)
¨
COMPONENT IN 1, 2 jacks (Y, PB, PR,AUDIO L/R)  Use these jacks to connect the component video/audio signals
from a DVD player or a Set-Top Box. (Refer to pages 21 and 23)
ˆ
PC VIDEO INPUT jackConnect to the video output jack on your PC.
Ø
PC AUDIO INPUT jack
Connect to the audio output jack on your PC.
(Refer to page 100)
∏
HDMI (High Definition Multimedia Interface)
INPUT jacks (HDMI IN 2)
Connect to the HDMI jack of a device with HDMI output. 
”
HDMI (High Definition Multimedia Interface)/ 
DVI INPUT jack (HDMI IN 1/DVI IN)
Connect to the HDMI jack of a device with HDMI output. 
This input can also be used as a DVI connection with separate
analog audio inputs. An optional HDMI/DVI cable will be 
necessary to make this connection. When using the optional
HDMI/DVI adapter, the DVI analog audio inputs on your TV allow
you to receive left and right audio from your DVI device.
(Not compatible with PC) (Refer to pages 21 and 23)’
DVI AUDIO (L/R) INConnect to the DVI audio output jack of an external device.
(Refer to page 23)
˝
DIGITAL AUDIO OUT (OPTICAL) jackConnect to a Digital Audio Component. (Refer to page 25)
Ô
RS232CFor service only.

SERVICE This jack is for service only.
Ò
ANTENNA terminalsTwo independent cables or antennas can be connected to 
these terminals. Use “ANT 1 IN (CABLE)” and “ANT 2 IN (AIR)”
terminals to receive a signal from VHF/UHF antennas or your
cable system. (Refer to pages 16~18)
Ú
POWER IN
Connect the supplied power cord.
BP68-00588G-01Eng(002~015)  5/12/06  5:55 PM  Page 12 
						

							English - 13
Remote Control
You can use your remote control within a distance of 23 feet and an angle of 30 degrees from the left
and right sides of the TV’s remote control receiver. You can also use your remote control to operate your
VCR, Cable box, DVD player and Set-top box. See pages 34~40 for details. 
1. POWERTurns the TV on and off.
2. Channel Number Press to directly tune to a particular channel.
3.-Press to select additional channels (digital
and analog) being broadcast by the same
station. For example, to select channel 
“54-3”, press “54”, then press “
-” and “3”.
4. ANTENNAPress to select “AIR” or “CABLE”.
5. CH MGRUsed to displays Channel Lists on the screen.
6. VCR/DVD ControlsControls VCR or DVD functions: Rewind, Stop,
Play/Pause, Fast Forward.
7. VOL +, VOL -Press to increase or decrease the volume.
8. MUTEPress to mute the TV sound.
9. MENUDisplays the main on-screen menu.
10. ▲, ▼, œ, √, ENTERPress to select highlight up, down, left, or
right. While using the on-screen menus,
press ENTER to activate (or change) a 
particular item.
11. INFOPress to display information on the TV
screen.
12. CAPTIONControls the caption decoder.
13. P.MODEAdjust the TV picture by selecting one of 
the preset factory settings (or select your
personal, customized picture settings.)
(Refer to page 56)
14. S.MODESelect Sound effect. (Refer to page 71)
15. MTS (Multichannel Television
Stereo)
Press to choose Stereo, Mono or SAP
(Secondary Audio Program).
16. Mode
(TV/DVD/STB/CABLE/VCR)
Selects a target device to be controlled by
the Samsung remote control (i.e., TV, DVD,
STB, CABLE, or VCR).
17. SOURCEPress to display all of the available video
sources (TV, AV1, AV2, AV3, S-Video1,
S-Video2, S-Video3, Component1,
Component2, PC, HDMI1, and HDMI2).
18. PRE-CHTunes to the previous channel.
19. DNSeDNSe enhances the sound quality,
automatically controls output,
and prevents sound distortion.
Press this button to set it On or Off. 
(Refer to page 72)
20. FAV.CH (Favorite Channel)Press to switch between your favorite 
channels.
21. CH /Press to change channels.
22. EXITPress to exit the menu.
23. SLEEPPress to select a preset time interval for
automatic shut off. 
(Refer to page 44)
24. P.SIZEPress to change the screen size. 
(Refer to page 59)
25. STILLPress to pause the current screen. 
(Refer to page 66)
26. RESETIf your remote control is not functioning
properly, take out the batteries and press
the reset button for about 2~3 seconds. 
Re-insert the batteries and try using the
remote control again. 
27. SETUsed during set up of this remote control, 
so that it will work compatibly with other
devices (Set-top box, VCR, Cable box,
DVD, etc.)
NOTES
•The Color buttons are used
during the channel list
function. (Refer to pages
48~51)
•This is a special remote
control for the visually
impaired, and has Braille
points on the POWER, VOL
+, VOL
-, CH  / , STOP,
and PLAY/PAUSE buttons.
BP68-00588G-01Eng(002~015)  5/12/06  5:55 PM  Page 13 
						

							Your New Wide TV
English - 14
Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote
control for a long time, remove the batteries and store them in a cool, dry place.
1
Lift the cover at the back of the remote control
upward as shown in the figure.
2
Install two AAA size batteries. Make sure to 
match the “+” and “–” ends of the batteries 
with the diagram inside the compartment.
3
Close the cover as shown in the figure.
NOTE
•Do not mix battery types, i.e, alkaline and manganese.
BP68-00588G-00Eng(002~015)  4/22/06  2:01 PM  Page 14 
						

							Connections
BP68-00588G-00Eng(002~015)  4/22/06  2:01 PM  Page 15 
						

							Connections
English - 16
Connecting VHF and UHF Antennas
If you do not have a cable system, you will need to connect an antenna to your TV.  
Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.
1
Plug the antenna lead into
the ANT 2 IN (AIR) on the 
rear panel of your TV.
BP68-00588G-00Eng(016~027)  4/22/06  4:02 PM  Page 16 
						

							English - 17
Connecting Cable TV
You can connect different cable systems to your TV, including cable without a Cable box, 
and cable with a Cable box that descrambles some or all channels.
Cable without a Cable Box
1
Plug the incoming cable into
the ANT 1 IN (CABLE) on the
rear panel of your TV.
Cable with a Cable Box that Descrambles All Channels
1
Find the cable connected to
the ANTENNA OUT 
terminal on your Cable box. 
This terminal might be 
labeled “ANT OUT”, “VHF 
OUT” or simply “OUT”.
2
Connect the other end of the
cable to the “ANT 1 IN
(CABLE)” terminal on the rear
panel of your TV.
BP68-00588G-00Eng(016~027)  4/22/06  4:02 PM  Page 17 
						

							Connections
English - 18
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the
cable that is connected to 
the ANTENNA IN terminal 
of your Splitter. 
This terminal might be 
labeled “ANT IN”, “VHF IN”
or simply, “IN”. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable
between an OUT terminal 
of the splitter and the IN 
terminal of the Cable box.
3
Connect a coaxial cable
between the ANTENNA OUT
terminal of the Cable box
and the B-IN terminal of the
RF (A/B) switch.
4
Connect another cable
between the other OUT 
terminal on the splitter and 
the A–IN terminal on the 
RF (A/B) switch.
5
Connect the last coaxial
cable between the OUT 
terminal of the RF (A/B) 
switch and the ANT 1 IN
(CABLE) on the TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. 
Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch 
to “B”, you will need to tune your Set-Top Box to the Cable boxs output channel, which is usually
channel 3 or 4.)
BP68-00588G-01Eng(016~027)  5/12/06  5:55 PM  Page 18 
						

							English - 19
Connecting a VCR
Connecting a VCR to the Video or S-Video/Audio jack
1
Connect a video cable
between the VIDEO IN (1   
or 2) (or S-VIDEO IN 1 or 2)
jack on the TV and the
VIDEO (or S-VIDEO)output
jack on the VCR.
2
Connect a set of audio
cables between the AUDIO
IN (1 or 2) jacks on the TV
and the AUDIO output jacks
on the VCR.
3
Connect a video cable
between the VIDEO OUT 
jack on the TV and the 
VIDEO input jack on the 
VCR.
4
Connect a set of audio
cables between the AUDIO 
OUT jacks on the TV and 
the AUDIO input jacks on 
the VCR.
NOTES
•For better video, use an 
S-Video cable.
•Please be sure to match the
color coded input terminals
and cable jacks.
•Connecting Video/Audio
cables from the Video and
Audio Out jacks on the TV to
the A/V In jacks on your VCR
enables you to record from
the TV onto the VCR.
TV Rear Panel
Incoming
Cable or 
Antenna
Stereo VCR
34
2
1or
BP68-00588G-01Eng(016~027)  5/8/06  5:52 PM  Page 19 
						

							Connections
English - 20
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a Camcorder to your TV.
You can use your camcorder to view tapes without using a VCR.
1
Locate the A/V output jacks
on the camcorder. They are
usually found on the side or
back of the camcorder.
2
Connect a set of audio
cables between the AUDIO 
IN jacks on the TV and the 
AUDIO output jacks on the
camcorder. If you have a
mono Camcorder, connect
L(mono) to the Camcorder
audio out using only one
audio cable.
3
Connect a video or S-Video
cable between the VIDEO IN 
(or S-VIDEO IN) jack on 
the TV and the VIDEO (or 
S-VIDEO) output jack on the 
Camcorder.
The audio-video cables shown
here are usually included with
a Camcorder. (If not, check 
your local electronics store.) 
If your Camcorder is stereo, 
you need to connect a set of 
two cables.
NOTE
•Please be sure to match the
color coded input terminals
and cable jacks.
Camcorder 
Output Jacks
1
TV Rear and right side
Camcorder
or
2
3
BP68-00588G-01Eng(016~027)  5/12/06  5:56 PM  Page 20