Samsung Ht C5500 User Manual

							
English 21
02 Connections
NOTE
Place the wireless receiver module at the rear of the listening position\
. If the wireless receiver module is too 
close to the product, some sound interruption may be heard due to interf\
erence.
If you use a device such as a microwave oven, wireless LAN Card, Bluetoo\
th equipment, or any other 
device that uses the same frequency (2.4/5.8GHz) near the product, som\
e sound interruption may be heard 
due to interference.
The transmission distance from the product to the wireless receiver modu\
le is about 10m, but may vary 
depending on your operating environment. If a steel-concrete wall or met\
allic wall is between the product 
and the wireless receiver module, the system may not operate at all, bec\
ause the radio wave cannot 
penetrate metal.
If the product doesn't make wireless connection, the product needs ID Se\
tting between the product and 
wireless receiver module. With the product turned off, press remote cont\
rol's number buttons 
"0""1" "3" "5" and turn on the product. With the wireless receiver module turned on\
, press "ID SET" 
button on the back of the wireless receiver module for 5 seconds.
CAUTION
Do not insert any other card except the provided TX card.  
If a different TX card is used, the product may be damaged or the card m\
ay not be removed easily.
Do not insert the TX card upside down or in the reverse direction.
   Insert the TX card when the product is turned off. Inserting the card wh\
en it is turned on may cause a 
problem.
If the TX Card is inserted and wireless receiver module setting is compl\
ete, sound is not output from the 
surround speaker connectors on the product.
  The wireless receiver antenna is built into the wireless receiver module\
. Keep it away from water and 
moisture.
For optimal listening performance, make sure that the area around the wi\
reless receiver module location is 
clear of any obstructions.
If no sound is heard from the wireless receiver module, switch the mode \
to DVD 5.1 channel or 
Dolby ProLogic II .
In 2-CH mode, no sound will be heard from the wireless receiver module.
✎




!








H T-C 5500_E LS _E N G _0217.in dd   2 1HT-C5500_ELS_ENG_0217.indd   212010-0 2-1 8     9 :2 2:5 32010-02-18    9:22:53
 
						

							
22 English
Connections
Connecting External Devices/your TV via HDMI
HDMI is a standard digital interface for connection to such devices as a\
 TV, projector, DVD player, Blu-ray 
player, set top box and more.
HDMI removes any loss of signal from analogue conversion, enabling you t\
o enjoy video and audio sound 
quality as it was originally created in the digital source.
HDMI OUT : Connecting to a TV with an HDMI Cable (BEST QUALITY)
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the bac\
k of the product to the 
HDMI IN jack on your TV.
 NOTE
Certain HDMI output resolutions may not work, depending on your TV.
If an HDMI cable is connected or removed during playback of a CD-DA, MP3\
 or JPEG fi le, the product will 
stop playing.
After making the video connection, set the Video input source on your TV\
 to match the corresponding Video 
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he SOURCE button on the remote 
control and select HDMI as the external source of the TV.
✎




DVD or Blu-ray Player SAT(Satellite/Set top box)
HDMI INHDMI OUT
HT-C 5500_E LS _E N G _0217.in dd   2 2HT-C5500_ELS_ENG_0217.indd   222010-0 2-1 8     9 :2 2:5 32010-02-18    9:22:53
 
						

							
English 23
02 Connections
HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT 
jack on your digital devices.
Press the  FUNCTION  button to select  HDMI 1 or HDMI 2  input.
The mode switches as follows : 
BD/DVD   D. IN   AUX    HDMI 1   HDMI 2   FM
HDMI Auto Detection Function
The product's video output will automatically change to HDMI mode when c\
onnecting an HDMI cable 
before power is on. For possible HDMI resolutions, see page 31.
This function is not available if the HDMI cable does not support CEC.
HDMI connection description- HDMI outputs only a pure digital signal to the TV.
-   If your TV does not support HDCP, random noise appears on the screen.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for prot\
ecting BD/DVD content outputted via 
HDMI from being copied. It provides a secure digital link between a vide\
o source (PC, DVD. etc) and a display 
device (TV, projector. etc). Content is encrypted at the source device\
 to prevent unauthorized copies from being 
made.
CAUTION
The Anynet+ function is supported only when an HDMI Cable is connected t\
o the HDMI OUT of the 
product.
1.
2.
•
•
•
!

H T-C 5500_E LS _E N G _0217.in dd   2 3HT-C5500_ELS_ENG_0217.indd   232010-0 2-2 2     7 :5 8:1 42010-02-22    7:58:14
 
						

							
24 English
Connections
METHOD 1 : Component Video  (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Co\
mponent video cable (not 
supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the\
 back of the product to the 
Component Video Input Jacks on your TV.
 NOTE
You can select from a variety of resolution settings such as 1080i, 720p\
, 576p(480p) and 576i(480i), 
depending on the disc type. (See page 31)
The actual resolution may differ from the setting in the Setup menu if b\
oth Component and HDMI cables are 
connected. The resolution may also be different depending on the disc. (\
See page 31)
After making the video connection, set the Video input source on your TV\
 to match the corresponding Video 
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he TV SOURCE button on the remote 
control and select COMPONENT as the external source of the TV.
In DVD playback, if both HDMI and Component jacks are connected and you \
select the Component 1080p, 
1080i, 720p or 576p(480p) mode, the Display Setup menu will show the o\
utput resolution as 1080p, 1080i, 
720p or 576p(480p) in the menu. The resolution is actually 576i(480i)\
.
METHOD 2 : Composite Video (GOOD QUALITY) 
Connect the supplied Video cable from the VIDEO OUT jack on the back of \
the product to the VIDEO 
IN jack on your TV.
NOTE
The VIDEO source is always output in 576i(480i) resolution regardless \
of the resolution set in the Setup 
menu. (See page 31)
After making the video connection, set the Video input source on your TV\
 to match the corresponding 
Video output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he TV SOURCE button on 
the remote control and select VIDEO as the external source of the TV.
CAUTION
Do not connect the unit through a VCR. Video signals fed through VCRs ma\
y be affected by 
copyright protection systems and the picture will be distorted on the te\
levision.
✎





✎



!

LAN
AUX INWIRELESSLAN
LAN
AUX INWIRELESSLAN
COMPONENT OUT
VIDEO OUT
Red
YellowMETHOD 1METHOD 2Blue Green
Connecting the Video Out to your TV
HT-C 5500_E LS _E N G _0217.in dd   2 4HT-C5500_ELS_ENG_0217.indd   242010-0 2-1 8     9 :2 2:5 42010-02-18    9:22:54
 
						

							
English 25
02 Connections
Connecting Audio from External Components
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-T\
op Box).
Connect the Digital Input (OPTICAL) on the product to the Digital Outp\
ut of the external digital 
component.
  Press the FUNCTION  button to select  D.IN input.
The mode switches as follows :  BD/DVD  D. IN   AUX   HDMI 1   HDMI 2   FM
NOTE
To see video from your Cable Box/Satellite receiver, you must connect it\
's video output to a TV.
This  s ys te m  s u p ports  D ig it a l  s a m plin g  fr e q uen cie s o f  3 2 k H z o f  h ig her fr o m  e xte rn al  d ig it a l  c o m ponen ts.This system supports Digital sampling frequencies of 32 kHz of higher fr\
om external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which \
is bitstream cannot be supported.
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR.
Connect AUX IN (Audio) on the product to the Audio Out of the external\
 analogue component.
 
Be sure to match connector colours.
 
Press the  FUNCTION  button to select  AUX input. 
The mode switches as follows :  BD/DVD  D. IN   AUX   HDMI 1   HDMI 2   FM
NOTE
  
You can connect the Video Output jack of your VCR to the TV, and connect\
 the Audio Output jacks of 
the VCR to this product.
1.
2.
•
✎



1.•
2. •
✎

HDMI INS
COMPONENT OUT
VIDEO OUT
LAN
HDMI OUT
WIRELESS LANOPTICAL
HDMI INS
COMPONENT OUT
VIDEO OUT
LAN
HDMI OUT
WIRELESS LAN
DIDITAL
AUDIO IN
AUX
Optical Cable
(not supplied) Audio Cable
 
(not supplied)
If the external analogue 
component has only one 
Audio Out, connect either 
left or right.
Set-Top BoxVCRWhite
Red
OPTICAL AUX
H
T-C 5500_E LS _E N G _0217.in dd   2 5HT-C5500_ELS_ENG_0217.indd   252010-0 2-1 8     9 :2 2:5 52010-02-18    9:22:55
 
						

							
26 English
Connections
Connecting to the Network
This product enables you to view network based services (See pages 57~6\
2) such as Internet@TV and
BD-LIVE, as well as receive software upgrades when a network connection \
is made. We recommend
using an AP (Access Point) or IP router for the connection.
For more information on router connection, refer to the user manual of t\
he router or contact the router
manufacturer for technical assistance.
Cable Network
Using the Direct LAN Cable (UTP cable), connect the LAN terminal of th\
e product to the LAN 
terminal of your modem.
Set the network options. (See page 38)
NOTE
Internet access to Samsung’s software update server may not be allowe\
d, depending on the router you use or the 
ISP’s policy. For more information, contact your ISP (Internet Servi\
ce Provider).
For DSL users, please use a router to make a network connection.
For the AllShare function, a PC must be connected in the network as show\
n in the fi gure.
1.
2.
✎



HDMI IN
COMPONENT OUT
VIDEO OUTAUX
HDMI OUT
WIRELESS LAN
HDMI IN
COMPONENT OUT
VIDEO OUTAUX
HDMI OUT
WIRELESS LAN
LAN
RouterBroadband modem Broadbandservice
Or
Broadband modem
(with integrated router)
Broadband service
Networking with PC forAllShare function
(See pages 61~62)
H T-C 5500_E LS _E N G _0217.in dd   2 6HT-C5500_ELS_ENG_0217.indd   262010-0 2-1 8     9 :2 2:5 62010-02-18    9:22:56
 
						

							
English 27
02 Connections
Wireless Network
You can connect to the network with a Wireless IP sharer.A wireless AP/IP router is required to make a wireless network connectio\
n. Connect the wireless
LAN adapter to the Wireless LAN Adapter on the rear panel of the product\
. 
Set the network options. (See page 38)
NOTE
This product is compatible with only Samsung's Wireless LAN Adapter. (n\
ot supplied) (Model name: WIS09ABGN).
-  The Samsung Wireless LAN Adapter is sold separately. Contact a Samsung E\
lectronics retailer for purchasing.
You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n\
 is recommended for stable operation of the 
wireless network.)
Wireless LAN, by its nature, may cause interference, depending on the us\
e condition (AP performance, distance, obstacles, 
interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not su\
pported.
When applying the security key for the AP (wireless IP sharer), only t\
he following is supported. Authentication Mode : WEP, WPAPSK, WPA2PSK
Encryption Type : WEP, AES
For the AllShare function, a PC must be connected in the network as show\
n in the fi gure.
Connecting the FM Antenna
Connect the FM antenna supplied to the FM 
75Ω COAXIAL Jack.
Slowly move the antenna wire around until 
you fi nd a location where reception is good, 
then fasten it to a wall or other rigid surface.
NOTE
   This product does not receive AM broadcasts.
1.
2.
✎





1)
2)

1.
2.
✎

OUTI OUT COMPONENT OUT
VIDEO OUT
LAN
AUX INWIRELESSLAN
I OUT
COMPONENT OUT
VIDEO OUT
LAN
AUX INWIRELESSLANWireless IP sharer
Wireless LAN Adapter
(not included)
Networking with PC for
AllShare function
(See pages 61~62)
PC
Broadband
service
WIiPod
FM ANT.
WIiPod
FM Antenna (supplied)
HT-C 5500_E LS _E N G _0217.in dd   2 7HT-C5500_ELS_ENG_0217.indd   272010-0 2-1 8     9 :2 2:5 82010-02-18    9:22:58
 
						

							
28 English
Setup
Before Starting (Initial Settings)
Turn on your TV after connecting the product.
(When the product is connected to TV for the fi rst 
time,  product  will turn on automatically and the 
Initial Settings screen will be displayed.)
 > Move s Select
Initial Settings I On-Screen Language
Select a language for the on-screen displays.
English
Français
Deutsch
Español
Italiano
Nederlands
Press the ▲▼ buttons to select the desired 
language, then press the  ENTER button.
Press the  ENTER button to select Start button.
     a Previous " Select
Initial Settings
TV Aspect, Musical Auto Calibration and Network will be set.
Each setting may be changed later under "Settings"
Start
Press the ▲▼ buttons to select desired TV 
Aspect ratio, then press the  ENTER button. 
(See page 29)
Musical Auto Calibration  screen will be displayed.
Plug the ASC microphone into the  ASC IN jack 
on the product. (See page 34)
Press the  ENTER button to select Start button.
       d Skip
Initial Settings I Musical Auto Calibration
Preparing...
Setting the Musical Auto Calibration function 
takes about 3 minutes.
1.
2.
3.
4.
5.
6.
Press the ◄► buttons to the select the 
desired Network Settings: Wired, Wireless or 
PBC (WPS), then press the  ENTER button. 
(See pages 38~41)
The Network Test will start and Initial Settings 
will be completed.
a Previous d Skip < Move " Select
Initial Settings I Network
Network Setting is needed to use various Internet services.
Choose the primary method for connecting to network.
Wired : Set the network by using Ethernet cable.
Please make sure that Ethernet cable is connected.
WiredWirelessPBC (WPS)
Press the  OK button. 
The home menu will be displayed. (For more 
information about home menu, please see 
page 29)
Home Menu
internet radioYou Tube
No Disc a Change Device   d View Devices " Enter
Please activate Internet@TV service
to enjoy a variety of Internet Services.
 NOTE
When the product is connected to TV for the 
fi rst time, product will turn on automatically.
Do not confuse because this is not 
malfunction.
The home menu will not be displayed if you do 
not confi gure the initial settings.
If you press the  BLUE(D) button during the 
Musical Auto Calibration/Network setup, you 
can access the home menu even if the 
network setup is not completed yet.
When you return to home menu, the full 
screen mode will be cancelled automatically.
7.
8.
•
✎




H T-C 5500_E LS _E N G _0217.in dd   2 8HT-C5500_ELS_ENG_0217.indd   282010-0 2-1 8     9 :2 3:0 02010-02-18    9:23:00
  
						

							
English 29
03 Setup
If you want to display Initial Settings screen 
again in order to make changes, press the 
STOP ( ) button on the front panel of the 
product for more than 5 seconds with no disc 
inserted.
Use the HDMI cable to connect the product to 
an  Anynet+(HDMI-CEC) -compliant Samsung TV.
If the TV uses a language supported by the 
product, that language will be set to a 
preferred language automatically.
However, the  Anynet+(HDMI-CEC)  feature 
should be set to  On in both TV and the 
product.
If the product is left in the stop mode for more 
than 5 minutes without being operated, a 
screen saver will appear on your TV. If the 
product is left in the screen saver mode for 
more than 25 minutes, the power will 
automatically turn off except during playback 
of a CD-DA (Automatic Power-Off Function).
Setting the Menu
DISC MENU MENU TITLE MENU
TOOLS
RETURN EXIT
INFO
TUNER
POPUP
DISC MENUTITLE MENU
TOOLSINFO
TUNER
POPUP1
2
4
3
1MENU Button : Press this to move to the home menu.
2RETURN  Button : Return to the previous menu.
3
ENTER / DIRECTION  Button:
Press the arrow buttons to move the cursor and select 
an item.
Press the  ENTER button to launch the selected item or 
confi rm the setting.
4EXIT  Button : Press this to exit the menu.


Press the  POWER button.
The Home Menu will appear.
Home Menu
internet radioYou Tube
No Disc a Change Device   d View Devices " Enter
Please activate Internet@TV service
to enjoy a variety of Internet Services.
1
2
4
3
5
6
1Selects the Internet@TV.
2Selects the Videos.
3Selects the Music.
4Selects the Photos.
5Selects the Settings.
6Displays buttons available.
Press the ◄► buttons to select  Settings, 
then press the  ENTER button.
Press the ▲▼ buttons to select the desired 
submenu, then press the  ENTER button.
Press the ▲▼ buttons to select the desired 
item, then press the  ENTER button.
Press the  EXIT button to exit the menu.
NOTE 
When the product is connected to the network, 
select Internet@TV from the home menu. 
Download desired content from  Samsung AppS.
The access step may differ depending on the 
selected menu.
The OSD (On Screen Display) may change in 
this product after upgrading the software 
version.
1.
•
2.
3.
4.
5.
✎



H T-C 5500_E LS _E N G _0217.in dd   2 9HT-C5500_ELS_ENG_0217.indd   292010-0 2-1 8     9 :2 3:0 72010-02-18    9:23:07
 
						

							
30 English
Setup
Display
You can confi gure various display options such as 
the TV Aspect, Resolution, etc. 
TV Aspect
Depending on the type of television you have, you 
may want to adjust the screen setting.
16:9 Normal•
Certain movies(4:3 source) 
will be displayed in 4:3 
Pillarbox (black bars on sides 
of picture) if 16:9 normal is 
selected.
16:9 Wide•
You can view the full 16:9 
picture on your widescreen 
TV.
4:3 Letter Box•
Select when you want to see 
the total 16:9 ratio screen 
Blu-ray Disc/DVD supplies, 
even though you have a TV 
with a 4:3 ratio screen. Black 
bars will appear at the top 
and bottom of the screen.
4:3 Pan-Scan•
Select when you want to see 
the 16:9 video supplied by the 
Blu-ray Disc/DVD without the 
black bars on top and bottom, 
even though you have a TV 
with a 4:3 ratio screen(extreme 
left and right portion of the 
movie picture will be cut off).
NOTE
Depending on the disc type, some aspect ratios 
may not be available.
If you select an aspect ratio and option which is 
different than the aspect ratio of your TV screen, 
then the picture might appear to be distorted.
If you select the 4:3 Pan-Scan or 4:3 Letter Box, 
you can't see full screen by pressing the FULL 
SCREEN  button on the remote control. 
✎



BD Wise (Samsung Products only)
BD Wise is Samsung's latest inter-connectivity feature.
When you connect Samsung products with 
BD-Wise to each other via HDMI, the optimum 
resolution will be set automatically.
Off  : The output resolution will be fi xed 
according to the Resolution previously set, 
regardless of the resolution of the disc.
On  : The original resolution of the BD/DVD disc 
will be output to the TV.
NOTE
If you want to change the resolution in BD 
Wise, you must set BD Wise to  Off in advance.
If you set off the BD Wise, the resolution of the 
connected TV will be adjusted to its maximum 
resolution automatically.
If the product is connected to a device that 
does not support BD Wise, you can not use 
BD Wise function.
For a proper operation of BD Wise, set each BD Wise 
menu of the product and the TV to  On respectively.
Resolution
Sets the output resolution of the Component and 
HDMI video signal.
The number in 1080p, 1080i, 720p, 576p(480p), 
576i(480i) indicates the number of lines of video. 
The i and p indicate interlace and progressive 
scan, respectively.
Auto  : It automatically checks and sets the optimal 
resolution. (HDMI only)
BD Wise  : Automatically sets the optimal 
resolution when connected via HDMI to a TV with 
the BD Wise feature. (The BD Wise menu item 
appears only if BD Wise is set to On.) (HDMI only)
1080p  : 
Outputs 1080 lines of progressive video. (HDMI only)
1080i : Outputs 1080 lines of interlaced video.
720p  : Outputs 720 lines of progressive video.
576p/480p  : Outputs 576(480) lines of progressive 
video.
576i/480i  : Outputs 576(480) lines of interlaced 
video. (Component & VIDEO only)
•
•
✎




•
•
•
•
•
•
•
H T-C 5500_E LS _E N G _0217.in dd   3 0HT-C5500_ELS_ENG_0217.indd   302010-0 2-1 8     9 :2 3:0 92010-02-18    9:23:09