Samsung Ht Ds1000 Instruction Manual

							20
CONNECTIONS
• If you connect the HDMI and Component outputs (PR, PB, Y) at the same time, the Component output
resolution changes automatically to the designated HDMI resolution.
Example: If the TV connected to HDMI can only support up to 480p, the HDMI and Component outputs are
all converted to 480p, even if you select the resolution switch to 1080i.
• Since this product has an embedded Video Upscaler function with Faroudja DCDi technology, it can
enhance a 480i DVD resolution output to 480p/720p/1080i. 
• You do not have to make separate adjustments, since the Home Theater and TV will be automatically adjust
themselves to the optimal resolution and aspect ratio if connected to HDMI. (If the TV is an HDTV and has
an HDMI Video/Audio Input jack, output is automatically converted to the resolution of 1080i.)
• Audio will not be output if decoder is not embedded in TV during 5.1 channel disk playback.
• Component output will give video in ‘480P’ mode only during DVD disc playback applied with Macrovision.
• Macrovision processes scramble on analog output to prevent illegal recording. Accordingly, if you are using
HDMI only, it can output 480P/720P/1080i, but is limited to 480p only if you are using component. 
• See your TV owners manual for more information on how to select the TVs Video Input source.
Note
Connect if the TV has an HDMI Video/Audio In jack.
Connect the HDMI Video/Audio Out to
the HDMI Video/Audio Input on the TV. 1
Set the Video Input source on your TV
to the corresponding HDMI output on
your Home Theater.2
Method 3When you connect to HDMI Video/Audio 
What is HDMI (High Definition Multimedia Interface)?
This device transmits DVD video and audio signals digitally without the process of
converting to analog. You can get sharper digital pictures by connecting the video to the
TV using an HDMI connection cable. 
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 23
 
						

							Connecting the Video Out to TV
21
You can adjust the resolution switch to set the HDMI and component (PR, PB, Y) output resolution  to
480p/720p/1080i.
Example: If the TV supports resolution up to 480p 
Press and hold DCDibutton on the remote
control for over 3 seconds.
•Each time the button is pressed, the selection alternates between
DCDi ONand DCDi OFF.
•If you connect the HDMI and Component outputs (PR, PB, Y) at the same
time, Component output resolution changes automatically to the
designated HDMI resolution. 
Caution
Selecting Resolution
Converts the interlace signal to progressive to prevent flickering and to
remove distortion or noise on the edge of screen.
DCDi (Directional Correlational Deinterlacing)Function
Set the resolution switch to 480p.
•A 480p video signal is output through the HDMI and
component outputs (P
R, PB, Y).
1
• If copy protection is in place, output resolution is automatically converted to 480p when you play the DVD,
even if you set the resolution to 720p or 1080i.
Note
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 24
 
						

							22
CONNECTIONS
Connect the Anynet input terminal on the back of this unit to your Samsung TVs Anynet
output terminal.1
Connect the Anynet Out Terminal on the back of this unit to the Anynet input of Samsung
external AV devices.2
VIDEO INOther AV devices
Samsung DVD player
Samsung VCR
Samsung Set-Top Box
VIDEO OUT ANYNET
TERMINAL
Use this to connect Anynet-enabled 
AV devices when necessary.
How to Connect to Anynet
Using the Anynet function, the DVD Home Theater System can be conveniently controlled from
your Samsung TV. By connecting the Anynet output terminal on the DVD Home Theater
System to the input terminal of any Samsung Anynet-enabled device, both can be controlled
from your TV. For detailed operation instructions and connection diagram, refer to the users
manual of your Anynet-enabled TV.
What is Anynet?
•The Anynet function allows you to use your TVs remote control and menu to control all AV devices.
•However, this function is available only with Samsung Anynet-enabled models.
Refer to the users manual of your Anynet-enabled TV and activate the Anynet function.3
*This function is available only with Anynet-enabled TVs.
•If the Anynet input and output terminals are reversed, communication with the TV will fail and
you will not be able to use the Anynet function.Caution
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 25
 
						

							Connecting External Components
23
Example: Digital signal components such as a Settop Box or CD Recorder.
Connecting an External Digital Component
Optical Cable
(not included)
Press AUXon the remote control to select ‘D.IN 1 or D.IN 2’.
•Each time the button is pressed, the selection changes as follows: D.IN 1➝D.IN 2➝AUX.
•You can also use the FUNCTIONbutton on the main unit.
The mode switches as follows: DVD/CD➝ D.IN 1➝D.IN 2➝ AUX➝ FM.
Connect the Digital In 1 or 2 (OPTICAL) on the main unit to the Digital Output on the
external digital component.1
2
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 26
 
						

							•To listen TV sound in 5.1 channel sound through the main unit, connect the Audio In on the
main unit to the Audio Output on the TV.
•You can connect Video Output jack on the VCR to the TV, and connect Audio Output jack on
the VCR to the HT-DS1000.
LR
24
Example: Analog signal components such as a VCR or TV.
Connecting an External Analog Component
Audio Cable
If the external analog
component has only one
Audio Out, connect either left
or right.
CONNECTIONS
Note
Press AUXon the remote control to select AUX.
•Each time the button is pressed, the selection changes as follows: D.IN 1➝D.IN 2➝AUX.
•You can also use the FUNCTIONbutton on the main unit.
The mode switches as follows: DVD/CD➝ D.IN 1➝D.IN 2➝ AUX➝ FM.
Connect Audio In on the main unit to Audio Out on the external analog component.
•Be sure to match connector colors.
1
2
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 27
 
						

							25
Connecting the FM Antenna
FM antenna connection
1. Connect the FM antenna supplied to the FM 75ΩCOAXIAL terminal as a temporary
measure.
2. Slowly move the antenna wire around until you find a location where reception is
good, then fasten it to a wall or other rigid surface.
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 28
 
						

							26
•Each time the button is pressed, the TV indicator (red) and the DVD Receiver indicator (green) will flash alternately.
•You can operate the TV while the TV indicator is flashing and the DVD player while the DVD indicator is flashing.
•Buttons Enabled for TV Operation: POWER, CHANNEL, VOLUME, TV/VIDEO, and Numeric (0-9) buttons.
•By default, the remote control is set to work with Samsung TVs. See page 65 for more information on the operation of the remote control.
Press MODEbutton.
To Operate the TV and DVD Player with a Single Remote Control
23
Press the TV/DVD
RECEIVERbutton so that
the TV indicator on the
remote control flashes.
TVDVD RECEIVER
TVDVD RECEIVER
Press the POWER
button to turn on
the TV.
56
Press the MODEbutton so
that the DVD RECEIVER
indicator on the remote
control flashes.Press TV/DVD
RECEIVERbutton
to select DVD/CD
mode.
Before Using Your DVD Player
Your DVD player is capable of playing DVD, CD, MP3 and JPEG discs.Depending on the disc you
are using, these instructions may vary slightly. Read the instructions carefully before using.
1
Plug the power
cord into the AC
power supply.
4
Press TV/VIDEO
button to select
VIDEO mode.
CONNECTIONS
•If you move the product during playback, the disc may be damaged.
•If you push the disc window up or down by  hand, it may cause a breakdown.
•Do not let children insert their fingers into the unit.
Note
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 29
 
						

							27
Disc Playback
2
1
Press OPEN/CLOSEbutton to open the
disc tray.
3
Press OPEN/CLOSEbutton to close the disc
window.
•The disc plays automatically when the disc window is closed.
•The disc menu may appear differently depending on the disc.
DVDCD
•Playback starts automatically.
Insert the disc so that the printed side
faces up.
•To resume playback, press PLAY/PAUSE(          )
button again.
To temporarily pause playback, 
press PLAY/PAUSEduring playback.
•If pressed once, “PRESS PLAY” is displayed and the
stop position will be stored in memory. 
If PLAY/PAUSE(          ) button or ENTERbutton is
pressed, playback resumes from the stop position.
(This function works only with DVDs.)
•If pressed twice, “STOP” is displayed, and if
PLAY/PAUSE(          ) button is pressed, playback
starts from the beginning.
To stop playback, 
press STOPduring playback.
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 30
 
						

							28
CONNECTIONS
•In this manual, the instructions marked with DVD (               ) are applicable to
DVD-VIDEO, DVD-AUDIO, and DVD-R/RW discs.
Where a particular DVD type is mentioned, it is indicated separately.
•Depending on the content of the disc, the initial screen may appear different.
DVDNote
Groups and tracks (DVD-AUDIO)
•DVD-audio is divided into several large sections called groups and smaller
sections called tracks. Numbers are allotted to these sections. 
These numbers are called group numbers and track numbers.
GROUP 1 GROUP 2
TRACK 1 TRACK 2 TRACK 1 TRACK 2TRACK 3
Titles and chapters (DVD-VIDEO)
•DVD-video is divided into several large sections called titles and smaller
sections called chapters. Numbers are allotted to these sections. 
These numbers are called title numbers and chapter numbers.
TITLE 1 TITLE 2
CHAPTER 1 CHAPTER 2 CHAPTER 1 CHAPTER 2CHAPTER 3
Tracks (Video and music CDs)
•Video and music CDs are divided into sections called tracks. 
Numbers are allotted to these sections. These numbers are called track numbers.
TRACK 1 TRACK 2 TRACK 4 TRACK 5TRACK 3
.
Disc terminology
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 31
 
						

							29
•Depending on the recording mode, some MP3-CDs may not play.
•Table of contents of a MP3-CD varies depending on the MP3 track format
recorded on the disc.Note
MP3-CD Playback
Data CDs (CD-R, CD-RW) encoded in MP3 format can be played.
2
In Stop mode, use    
to select
the album, and
then press the
ENTERbutton.
•The MP3 menu screen will appear
and playback will start.
•Depending on the MP3 disc, the
appearance of the menu may be
different.
1
Press the
OPEN/CLOSEbutton
to open the disc
windows, and then
load the MP3 disc.
4
Press the STOP
button to stop
playback.
•To select another album and track,
repeat Steps 2 and 3 above.
3
To change the album,
use                    to
select another album
in Stop mode, and
then press the
ENTERbutton.
Something like you
Back for good
Love of my life
More than words
I need you
My love
Uptown girlDVD RECEIVER                                     SMART NAVI
 1p~44p(DS1000)-sea  9/15/04 2:43 PM  Page 32