Samsung Sp M220 User Manual

Installation and Connection2-8
 All resolutions higher or lower than 1024x768 are converted to 1024x768 by the Scaler chip inside the projector. If the 
resolution of the signal out put by the PC matches the real resolution (1024x768) of the projector, the screen quality is 
optimal. 
 
AV Timing (D-Sub)
AV Timing (HDMI)
VESA 1280 x 960 72Hz 72.072 72.000 124.540
VESA 1280 x 960 75Hz 75.231 74.857 130.000
VESA 1280 x 1024 60Hz 63.981 60.020 108.000
VESA 1280 x 1024 70Hz 74.620 70.000 128.943
VESA 1280 x...

2-8Installation and Connection
AV Timing (VIDEO)
NTSC, NTSC 4.43, PAL, PAL60, PAL-N, PAL-M, SECAM
Your projector supports the standard video formats listed above through its video inputs. No adjustments are 
necessary.
EIA-861Format5 1920 x 1080 Interlaced 60.000 33.750 74.250
EIA-861Format17,18 720 x 576 Progressive 50.000 31.250 27.000
EIA-861Format19 1280 x 720 Progressive 50.000 37.500 74.250
EIA-861Format20 1920 x 1080 Interlaced 50.000 28.125 74.250
FORMATRESOLUTIONSCAN
HORIZONTAL 
FREQUENCY...

Installation and Connection2-9
2-9 Connecting the Power
1.Plug the power cord into the power terminal on the rear side of the projector.
Downloaded From projector-manual.com Samsung Manuals 

2-10Installation and Connection
2-10 Connecting with a PC and Setting up the PC
2-10-1. Setting up the PC Environment 
Check the following items before connecting your PC to your projector. 
1.Click the right mouse button on the Windows desktop, and then click [Properties]. 
The  dialog appears.
2.Click the [Settings] tab, and then set the . The optimal resolution for the projector is 1024 x 768. For other 
resolutions supported by the projector, see the PC Timing Display Mode table in section 2-8.
 You...

Installation and Connection2-10
 Setting the refresh rate sets both the vertical and horizontal frequencies. 
5.Click the [OK] button to close the window, and then click the [OK] button on the  window to close that 
window.
6.Shut down the PC and connect it to the projector.
 The setup process might vary depending on your type of computer or version of Windows. 
(For example, [Properties] appears instead of [Properties (R)] as shown in 1.)
This projector supports 32 bit color quality (per pixel) when it...

2-10Installation and Connection
1.Turn on the projector, and then  press the [SOURCE] button to select .
If the  Mode is not available, make sure the PC video cable is properly connected. 
2.Turn on the PC, and then set the PC Environment (screen resolution, etc.) if necessary. 
3.Adjust the screen. 
Downloaded From projector-manual.com Samsung Manuals 

Installation and Connection2-11
2-11 Connecting a PC using an HDMI/DVI cable
Make sure that your PC and projector are turned off.
1.Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVI 
cable (Not supplied).
- If you are connecting to the HDMI terminal of your PC, use an HDMI/HDMI cable (Not supplied).
- For the supported resolutions and refresh rates, see PC Timing (D-Sub/HDMI) in Section 2-8, Supported Display Modes. 
Downloaded From...

2-12Installation and Connection
2-12 Connecting an HDMI-Compatible Device
Make sure that the AV device and your projector are turned off.
1.Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital output 
device using an HDMI/DVI or HDMI/HDMI cable.
- If you are connecting to the HDMI output terminal on the digital output device, use an HDMI/HDMI cable.
- For supported input signal formats, resolutions, and frequencies, see AV Timing(HDMI) in...

Installation and Connection2-13
2-13 Connecting an AV device using a D-Sub cable
Make sure that the AV device and your projector are turned off.
1.Connect the [PC IN] terminal at the back of the projector to the D-Sub terminal of your AV device using a D-Sub cable.
- For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-8, Supported Display 
Modes. 
2.Connect the [AUDIO IN (L-AUDIO-R)] terminal at the back of the projector to the Audio out terminal of your...

2-14Installation and Connection
2-14 Connecting an AV device with component output
Make sure that the AV device and your projector are turned off.
1.Connect the [PC IN] terminal on the back of the projector to the Component terminal on your AV device using a D-Sub to 
Component cable (Not supplied). This cable has a D-Sub connector on one end and three RCA jacks on the other.
- For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-8, Supported Display...