Samsung SP P4251 Plasma Display User Manual

1 
The wall mount comes packaged in 3 parts. These parts must be assembled together.
Please tighten the captive screw in the direction of the arrow after assembling 
the bracket. Install the Wall Mount Bracket after the screws are securely inserted 
into the wall.
2 
After installing the Wall Mount  Bracket,
assemble the support bars and hinges 
(as illustrated) using screws provided. 
(12 screws(
@) are provided. For safety
reasons, make sure all 12 screws are 
firmly attached.)
11
How to assemble the...

1 
Remove the screws from the back of the PDP.
2 
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire a specialist to install the wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened. Otherwise the PDP...

13
Note
•Contact an authorized technician when installing the wall attachment panel.
•After hanging the PDP panel on the wall attachment panel, make sure that the Insulation 
holders are completely hung. 
•Be careful not to get your fingers caught during installation.
•Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may 
fall down.
•Please secure the mounting bracket on the wall surface after setting its angle at 0°.
How to Adjust Mounting Angle
Notice  Notice :...

How to assemble the Stand-Base
14
1 
Assemble two support pins with the stand base and firmly secure both sides of the 
support pins using 8 screws provided.
2 
Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided.
➤ ➤Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage
to the screen. Always store the PDP upright.
Warning
Firmly secure the stand for the PDP before
moving it, as the stand may fall and 
could cause serious injury....

PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................16
Connecting Cable TV ....................................................................17
Connecting a VCR ........................................................................19
Connecting a Camcorder ..............................................................20
Connecting a DVD Player ..............................................................21
Connecting a DTV Receiver...

Connecting VHF and UHF Antennas
16
Antennas with 75-ohm Round Leads
If your antenna looks like this:  it has 75-ohm round leads.  
1
Plug the antenna lead into the VHF/UHF terminal 
on the PDP.
Use the Antenna Cable, an accessory included 
in the product package. 
BN68-00731A-00Eng_002-023  2004.6.3  11:12 AM  Page 16 

17
Connecting Cable TV
You can connect different cable systems to your PDP, including cable without a cable box, 
and cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
1 
Plug the incoming cable into the VHF/UHF terminal on
the PDP.
Use the Antenna Cable, an accessory included 
in the product package. 
Cable with a Cable Box that Descrambles All Channels.
1 
Find the cable connected to the ANTENNA OUT 
terminal on your cable box. This terminal might be 
labeled ANT...

18
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the cable that is 
connected to the ANTENNA IN terminal of
your cable box. 
This terminal might be labeled ANT IN, 
VHF IN or simply, IN. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable between an 
OUTPUT terminal of...

19
Connecting a VCR 
Connecting a VCR to the Video or S-Video/Audio jack
S-Video Cable
Audio Cable
Video Cable
Power Plug
Connect the Video/Audio cables between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the PDP
and VIDEO or S-VIDEO / L - AUDIO - R output jacks on the VCR. 
(Note: For better video, you can use
an S-Video cable.)
Note
•Please be sure to match the color coded input terminals and cable jacks.
Videotape Playback:
1. Turn on your PDP.
2. Press the SOURCE button to select “Video(AV1, AV2 or...

20
Connecting a Camcorder
Audio Cable
S-Video Cable
Video Cable
Power Plug
Connect a Video/Audio cable between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the PDP
and the VIDEO or S-VIDEO /AUDIO output jacks on the camcorder. (Note: For better video, you
can use an S-VIDEO cable)
Note
•Please be sure to match the color coded input terminals and cable jacks.
Viewing Tapes
1. Turn on your PDP.
2. Press the SOURCE button to select “Video(AV1, AV2 or AV3)” or “S-VIDEO(S-VIDEO1 or 
S-VIDEO2)”.
3. Turn on...