Sanyo 4 Head Vcr Manual

							31
To record a broadcast at a specific time
and date
, repeatedly press PLAY or STOP
to select the specific date.
Press 
FA S T -F to store your selection.
9. Repeatedly press 
PLAY or STOP to select
the start hour. When the correct hour
appears, press 
FA S T - F. Then repeatedly
press 
PLAY or STOP to select the minute
and press 
FA S T -F.
10. Repeat Step 9 to set the end time.
11. Repeatedly press 
PLAY or STOP to select
the channel. 
To record from a source connected to the
AUDIO IN 1/VIDEO IN 1 (or AV 2 for the
Model 62) jacks, repeatedly press 
PLAY or
STOP until LINE (LINE 1 or LINE 2 on
the Model 62) appears.
12. Repeatedly press 
PLAY or STOP to select
the tape speed (
SP, LP, or EP).
13. Double-check all the set information.
• If the information is correct, press 
PROG.
• If an entry is not correct, repeatedly
press 
FA S T - F or REW to move the cursor
to the incorrect entry, enter the correct
information, then press 
PROG.
The timer settings appear on the TV
screen. To enter another setting, repeat-
edly press 
PLAY or STOP to select another
timer number and repeat Steps 7–13.
14. Press 
PROG again. TURN VCR OFF FOR
TIMER
 RECORDING briefly appears.
15. Press 
POWER to turn off the VCR. TIMER
appears.Notes:
• Be sure that TIMER appears when you
turn the VCR off. If it does not appear,
check your entries.
• If you load a cassette with its erase-pro-
tection tab removed and set the VCR’s
timer, the VCR ejects the cassette and
flashes TIMER.
• If you set up the VCR to record a cable
broadcast through a cable box, be sure to
leave the cable box turned on and tuned to
the desired station before the broadcast
starts.
• You can manually turn on and operate the
VCR before the set times, but the VCR
starts an automatic timer recording only if
the power is off at the set start time.
Monitoring an Automatic Timer 
Recording
1. Turn on the TV and set it to the same chan-
nel as 
3-CH-4 on the back of the VCR.
Note: If you are using a TV/monitor that is
connected to the VCR’s 
AUDIO/VIDEO OUT
jacks, set the TV/monitor to the video
mode.
2. Press 
TV/VCR until VCR appears.
Checking/Changing Timers
1. Turn on the TV and set it to the same chan-
nel as 
3-CH-4 on the back of the VCR.
Note: If you are using a TV/monitor that is
connected to the VCR’s 
AUDIO/VIDEO OUT
jacks, set the TV/monitor to the video
mode.
SELE CT  START  DATE
DATE START STOPCH
  EP
SET
       :         KEY   SELECT :          KEY                                   END       : PROG  KEY                
TODAY8  SAT --:--   --:--  --
16-549.fm  Page 31  Tuesday, July 20, 1999  5:04 PM 
						

							32
2. Turn on the VCR and repeatedly press TV/
VCR
 until VCR appears.
3. Press 
PR OG. The first four timer settings
appear.
4. Repeatedly press 
PLAY or STOP to select
the setting you want to change, then press
FA S T- F. 
5. Follow Steps 8–12 under “Setting a Timer”
on Page 30 to correct the selected setting.
6. When you finish, press 
PROG again, then
turn off the VCR.
Clearing a Timer
If the timer recording has not yet started:
1. Follow Steps 1–3 under “Checking/Chang-
ing Timers.”
2. Highlight the setting you want to clear, then
press 
ADD/DLT.
3. When you finish clearing the timer, press
PROG.
Turn off the VCR if you still have at least one
timer setting entered.
If a timer recording is in progress:
1. Press POWER to stop timer recording. TO
CANCEL
 TIMER REC PUSH POWER
THEN
 STOP KEY appears if you are
watching the signal from the VCR.
2. Within 10 seconds, press 
STOP. TIMER
disappears.
DUBBING
The process of recording from one audio/video
device to another is called dubbing.
An audio/video device where a signal origi-
nates is called the dubbing source. You can
use another VCR, camcorder, satellite receiv-
er, or other device with A/V outputs as the dub-
bing source, connect the dubbing source and
the VCR, then use your VCR to record the sig-
nal from the dubbing source.
Or, you can use this VCR as the dubbing
source for another VCR. See “Installation” on
Page 9 for the various possible connections.
Notes:
• Always use video-quality shielded cables
with phono-type connectors to connect the
device to the VCR. Do not use standard
audio patch cords.
• Most material performed in public, such as
concerts, plays, and movies, or distributed
on prerecorded video tapes is copyrighted.
The unauthorized recording or duplication
of copyrighted material is a violation of the
copyright laws of most countries and such
duplication may result in fines, imprison-
ment, or both. Note, however, that in the
United States, it is not a violation of U.S.
copyright laws for a consumer to record a
broadcast television program for private
(in-home) viewing.
To dub a tape, start playback on the dubbing
source first (see that device’s instructions) then
start recording on the recording VCR.
2:00A08SP STOP    CH  SPD
16-549.fm  Page 32  Tuesday, July 20, 1999  5:04 PM 
						

							33
AUDIO-ONLY RECORDING 
(MODEL 62 ONLY)
Because of the superior quality of VHS Hi-Fi
audio recordings, you might want to use your
VCR as an audio-only recorder. You can also
make live recordings by connecting a pre-
amplifier or mixer to the VCR’s 
AUDIO IN jacks.
Simply select the line input and record as usu-
al.
Caution:
 Do not directly connect a microphone
to the VCR.
Note:
 For the best audio fidelity, we recom-
mend you use high-quality video tape (such as
Cat. No. 44-410) to make audio-only record-
ings.
16-549.fm  Page 33  Tuesday, July 20, 1999  5:04 PM 
						

							34
ADDITIONAL INFORMATION
TROUBLESHOOTING
If you follow the instructions in this manual and still have trouble operating your VCR, look in this
chart for the problem description and its solution. If your VCR still does not work properly, contact
your local RadioShack store.
PROBLEM POSSIBLE SOLUTION
No power. The power cord is not connected. Plug the power cord into an AC
outlet.
Timer recording did not work, 
or a broadcast was recorded 
at the wrong time.• The power is on. Turn off the power.
• The timer is not set or is set incorrectly. Check the timer set-
tings.
Cannot record. The erase-protection tab is missing. Place a piece of tape over the
tab hole.
Picture is poor on playback. • The TV is not set to the proper channel. Set the TV to Channel
3 or 4.
• The TV’s fine tuning is not set correctly. Fine tune your TV.
• Audio/video connections are incorrect. Check all connections.
The playback picture is dis-
torted.• The video heads are dirty. See “Cleaning the Video Heads” on
Page 37.
• The VCR might not have adjusted the tracking correctly. You
might need to manually adjust the tracking (see “Tracking” on
Page 26).
No picture on playback. • The TV is not set to the proper channel. Set it to Channel 3 or
4, or to its audio/video input if you connected it to the VCR’s
AUDIO/VIDEO OUT jacks.
• Audio/video connections are incorrect. Check all connections.
Remote control buttons do 
not work when the power is 
on and a cassette is loaded.• Something is blocking the path from the remote control to the
VCR.
• Bright light is shining on the VCR’s remote control sensor win-
dow. Get closer to the VCR, or change the VCR’s location.
• The remote control might be set for another device’s opera-
tion. Try pressing 
VCR.
• The remote control’s batteries might be weak. Replace the
batteries.
Cannot see broadcast TV 
programs using the VCR’s 
tuner.•
TV/VCR is not set correctly. Repeatedly press TV/VCR until
VCR appears.
• Audio/video connections are incorrect. Check all connections.
Cannot record from the input 
jacks.• Connections are incorrect. Check all connections.
•
INPUT is not set correctly. Select LINE (LINE 1 or LINE 2
for the Model 62).
16-549.fm  Page 34  Tuesday, July 20, 1999  5:04 PM 
						

							35
PROBLEM POSSIBLE SOLUTION
No stereo sound for a stereo 
recording (Model 62 only).• You have not connected the VCR’s AUDIO OUT jacks to a ste-
reo system or stereo TV. Connect the jacks to a stereo output.
• The audio out setting is not correctly set. Set it to 
Hi-Fi (see
“Receiving/Recording Stereo/SAP Broadcasts (Model 62
Only)” on Page 28).
• The VCR might not have adjusted the tracking correctly. You
might need to manually adjust the tracking (see “Tracking” on
Page 26).
16-549.fm  Page 35  Tuesday, July 20, 1999  5:04 PM 
						

							36
CARE AND MAINTENANCE
Your Optimus 4-Head VHS HQ VCR is an example of superior design and craftsmanship. The fol-
lowing suggestions will help you care for your VCR so you can enjoy it for years.
Keep the VCR dry. If it gets wet, wipe it dry immediately. Liquids might contain min-
erals that can corrode the electronic circuits.
Use and store the VCR only in normal temperature environments. Temperature ex-
tremes can shorten the life of electronic devices and distort or melt plastic parts.
Keep the VCR away from dust and dirt, which can cause premature wear of parts.
Handle the VCR gently and carefully. Dropping it can damage circuit boards and cas-
es and can cause the VCR to work improperly.
Use only fresh batteries of the required size and type in the remote control. Batteries
can leak chemicals that damage your VCR remote control’s electronic parts.
Wipe the VCR with a damp cloth occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong detergents to clean the VCR.
Modifying or tampering with the VCR’s internal components can cause a malfunction, invalidating
your VCR’s warranty and voiding your FCC authorization to operate it. If your VCR is not performing
as it should, take it to your local RadioShack store for assistance.
16-549.fm  Page 36  Tuesday, July 20, 1999  5:04 PM 
						

							37
Servicing Your VCR 
There are no user-serviceable parts inside your
VCR. If you encounter a problem that you can-
not correct using this manual and its trouble-
shooting guide, take the VCR to your local
RadioShack store for assistance.
Cleaning the Video Heads
When video head cleaning becomes neces-
sary, the VCR displays the following message
on the TV screen while playing back a record-
ed tape.
Video head cleaning kits are available from
your local RadioShack store. Clean the heads
only when the VCR displays the message
shown above. Be sure to use the “dry” type
cleaning cassette. 
Serious problems require cleaning by a trained
technician. For more head cleaning informa-
tion, contact your local RadioShack store.
Storing Your Video Cassettes
Unless you are making an automatic timer re-
cording, eject and store the cassette before
you turn off the VCR. This helps protect the
cassette and the VCR’s internal mechanisms.
Place your video cassettes in their protective
boxes and store them in a cool, dry, dust-free
environment. Store the cassettes on end, not
on their sides, to prevent improper settling of
the cassette’s spools.
Note: Tape can become wound too tightly
around the cassette’s spools after many play-
ings. This can make the cassette load improp-
erly and automatically eject when you insert it.
On most cassettes there is a brake-release
plunger on the bottom center of the cassette.
Use the tip of a pen or pencil to press the
plunger. This loosens the tape.
Brake-Release Plunger
16-549.fm  Page 37  Tuesday, July 20, 1999  5:04 PM 
						

							38
SPECIFICATIONS 
Television System  ..............................................................................  NTSC Standard Color Signal
Recording System ................................................................................  Four-Head Double Azimuth
Tape Width  ............................................................................................................................  
1/2 Inch
Tape Speed:
SP  ............................................................................................  1.31 Inch/second (33.35 mm/s)
LP  ............................................................................................  0.65 Inch/second (16.67 mm/s)
EP  ............................................................................................. 0.43 Inch/second (11.12 mm/s)
Tuner Channels:
VHF ...................................................................................................................................  2–13
UHF .................................................................................................................................  14–69
CATV ...............................................................................................................................  1–125
RF Converter  ...............................................................................................  Built-in VHF Converter
Converter Output  .....................................................................................................  Channel 3 or 4
Terminals:
Antenna Input  ................................................................................................ VHF/UHF: F Type
Antenna Output  ............................................................................................  VHF/UHF: F Type
Video Input/Output  .........................................................................................  Phono Connector
Audio Input/Output .........................................................................................  Phono Connector
Video Output Level  .............................................................................................................  1.0 V
p-p
Video Output Impedance  ......................................................................................................... 75 W
Audio Output Level  ..............................................................................................................  –8 dBV
Audio Output Impedance  .......................................................................................................... 1 kW
Video Input Level  ..........................................................................................................  0.5-2.0 V
p-p
Video Input Impedance  ..........................................................................................................  50 kW
Audio Input Level  ...............................................................................................................  –10 dBV
Audio Input Impedance  ..........................................................................................................  47 kW
Video S/N Ratio (weighted):
SP ..................................................................................................................................... 42 dB
EP ..................................................................................................................................... 40 dB
Audio S/N Ratio:
Regular Audio (weighted)
SP ..................................................................................................................................... 43 dB
EP ..................................................................................................................................... 40 dB
Hi-Fi Audio (Model 62 only) (Dynamic Range):
SP  ...................................................................................................................  More than 90 dB
LP  ...................................................................................................................  More than 90 dB
EP  ...................................................................................................................  More than 90 dB
16-549.fm  Page 38  Tuesday, July 20, 1999  5:04 PM 
						

							39
Frequency Response:
Regular Audio
SP  .................................................................................................................  80 Hz–10 kHz
EP  ...................................................................................................................  80 Hz–5 kHz
Hi-Fi Audio (Model 62 only) In All Modes ............................................................  20 Hz–20 kHz
Power Requirement  .....................................................................................................  120 V, 60 Hz
Power Consumption
Models 112/113  ...........................................................................................................  18 Watts
Model 62  .....................................................................................................................  23 Watts
Dimensions (HWD)  ................................................  3
5/8 ´ 1415/16 ´ 1113/16 Inches (9.3 ´ 38 ´ 30 cm)
Weight  .................................................................................................................  7 lbs 6 oz (3.4 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and
improvement without notice.
16-549.fm  Page 39  Tuesday, July 20, 1999  5:04 PM 
						

							RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
5A7Printed in Japan
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for ninety (90) days from the date of purchase from RadioShack company-
owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell3/97
16-549.fm  Page 40  Tuesday, July 20, 1999  5:04 PM