Sanyo Projector Plc Wxu700 User Manual
Have a look at the manual Sanyo Projector Plc Wxu700 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
61 This function provides the following options in the cooling fans’ operation when the projector is turned off (p.23). L1 ...... Normal operation L ...... Slower and lower-sound than the normal operation (L1), but it takes more time to cool the projector down. Fan Setting Fan control 0º 90º 180º 40º 50º140º50º 40º Fan Control Setting Choose the running speed of cooling fans from the following options according to the ground elevation under which you use the projector. Off .......Normal speed. Set this function to Off when using the projector in non-high altitude environment. On 1 ... Faster than Off mode. Select this mode when using the projector in high altitudes (about 1,200 meters or more above the sea level) where the fans have less cooling effect. On ....Faster than On 1 mode. Select this mode when using the projector in higher altitudes than above where the fans have lesser cooling effect. On 3.... Be sure to set the Lamp control in High and the Fan control in On 3 when using the projector inclined at between +40 degrees to +140 degrees to the horizontal plane at altitudes between 0 and approximately 1,600 meters above sea level. Note: • The fan noise becomes louder in On1 , On and On3. • Setting Fan control to On1 , On or On3 affects L operation in Fan. This function is used to display the cumulative lamp operating time and reset the lamp counter. When the lamp life is left 0 hour, the Lamp replacement icon (Fig.1) will appear on the screen, indicating that the end of lamp life is reached. When replacing the projection lamp, reset lamp counter. See "Resetting the Lamp Counter" on page 68. Lamp counter This icon appears on the screen when the end of lamp life is reached. Fig .1 Lamp replacement icon Note: At turning on, the icon (Fig.1) will appear. Note: The Lamp replacement icon (Fig.1) will not appear when the Display function is set to Off (p.49), during “Freeze” (p.28) or “No show” (p.29).
6 Setting Factory default This function returns all setting values except for the User logo, PIN code lock , Logo PIN code lock and Filter counter to the factory default settings. Factory default Warning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are displayed with the latest warning message at the top of the list, followed by previous warning messages in chronological order. Note: When the Factory default function is executed, all the warning log records will be deleted. This function is used to set a frequency for the filter cleaning. When the projector reached a specified time between cleanings, a Filter warning icon appears on the screen, notifying the cleaning is necessary. After cleaning the filter, be sure to select Reset and set the timer. The Filter warning icon will not turn off until the filter counter is reset. For details about resetting the timer, refer to "Resetting the Filter Counter" on page 65. Filter counter Filter counter 32H Press the SELECT button to select Timer and then use the Point ▲▼ buttons to set the timer. Select from ( Off/100H/ 00H/ 300H ) depending on the use environment. Filter warning icon appears on the screen at a set time. Fig .1 Filter warning icon Note: This icon also appears at turning on. Note: The Filter warning icon (Fig.1) will not appear when the Display function is set to Off (p.49), during “Freeze”(p.28), or "No show" (p.29).
63 Input Source Information Display The Information Menu is used for checking the status of the image signal being projected and the operation of the projector. H-sync freq . V-sync freq . Lamp counter Information Menu The horizontal frequency of the input signal is displayed in KHz or - - - - - when no signal. The vertical frequency of the input signal is displayed in Hz or - - - - - when no signal. Numbers of Hz doubles when during Interlace. The cumulative lamp operating time is displayed. Direct Operation Press the INFO. button on the remote control to display the Information Menu. INFO . button Remote Control Press the Point ▲▼ buttons to select Information . The Information Menu is displayed. See below for displayed information. Menu Operation Power management Screen Off , Ready , Shut down or Timer is displayed. The selected screen size is displayed. Input Lamp status The selected input source is displayed. The selected lamp mode is displayed. Information Language The selected language is displayed. Key lock The selected Key lock icon is displayed. PIN code lock Off , On 1 or On is displayed. Remote control The selected remote code is displayed.
64 The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. WARNING indicator The projector is shut down and the WARNING indicator is blinking red . When the temperature inside the projector reaches a certain level, the projector will be automatically shut down to protect the inside of the projector. The POWER indicator is blinking while the projector is being cooled down. When the projector has cooled down enough (to its normal operating temperature), it can be turned on again by pressing the POWER ON/STAND-BY button. The projector is shut down and the WARNING indicator lights red . When the projector detects an abnormal condition, it is automatically shut down to protect the inside of the projector and the WARNING indicator lights red. In this case, unplug the AC power cord and reconnect it, and then turn the projector on once again to verify operation. If the projector cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Maintenance and Cleaning Top Control Top Control Note: The WARNING indicator continues to blink even after the temperature inside the projector returns to normal. When the projector is turned on again, the WARNING indicator stops blinking. Then check the matters below: – Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if the air vents of the projector are not blocked. – Has the projector been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent. – Are the filters clean? Clean the filters periodically. WA R N I N G e m i t a red light WARNING blinking red
65 Maintenance and Cleaning Filter prevents dust from accumulating on the optical elements inside the projector. Should the filters become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If a Filter warning icon appears on the screen, clean the filters immediately. Clean the filters by following the steps below. CAUTION Do not operate the projector with the filters removed. Dust may accumulate on the optical elements degrading picture quality. Do not put anything into the air vents. Doing so may result in malfunction of the projector. RECOMMENDATION We recommend avoiding dusty/smoky environments when you operate the projector . Usage in these environments may cause poor image quality . When using the projector under dusty or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning. Be sure to reset the Filter counter after cleaning or replacing the filters. Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Setting and then press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select Filter counter and then press the SELECT button. Use the Point ▲▼ buttons to select Filter counter reset and then press the SELECT button. Filter counter Reset? appears. Select yes to continue. 1 Resetting the Filter Counter Filter counter Filter counter Reset? appears. Select yes , then another confirmation box appears. Select yes again to reset the Filter counter. Another confirmation dialog box appears, select yes to reset the Filter counter.3 Cleaning the Filters H Turn off the projector, and unplug the AC power cord from the AC outlet. Turn the projector over and remove the filters by pulling the latches upward. 1 Gently clean the filters by using a brush or rinse it softly.3 When rinsing the filters, dry they well. Replace the filters properly. Make sure that the filters are fully inserted to the projector.4 Filters Pull up and remove.
66 Maintenance and Cleaning Cleaning the Projector Cabinet Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner or use a lens cleaning paper or commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the surface of the lens. Unplug the AC power cord before cleaning. Gently wipe the projector body with a soft dry cleaning cloth. When the cabinet is heavily soiled, use a small amount of mild detergent and finish with a soft dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the surface of the cabinet. When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. Attaching the Lens Cap When moving the projector or while it is not in use, replace the lens cap. 1 2 Thread the string through the hole on the lens cap and then tie a knot in the string to secure it in place. To pass the other end of the string into the hole on the top of the projector and pull at it. Lens Cap String for the lens cap S e c u r e i t t o t h e h o l e with a screw. Hole
67
Maintenance and Cleaning
When the projection lamp of the projector reaches its end
of life, the Lamp replacement icon appears on the screen
and LAMP REPLACE indicator lights yellow. Replace the
lamp with a new one promptly. The timing when the LAMP
REPLACE indicator should light is depending on the lamp
mode.
For continued safety, replace with a lamp of the
same type. Do not drop a lamp or touch a glass
bulb! The glass can shatter and may cause injury.Allow a projector to cool for at least 45 minutes
before you open the Lamp Cover. The inside of
the projector can become very hot.
CAUTION
Lamp Replacement
CAUTION
Top Control
LAMP REPLACE
indicator
Lamp replacement icon
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
● Model No . of your projector : PLC-WXU700
● Replacement Lamp Type No . : POA-LMP111
(Se\
rvice Parts No . 610 333 9740)
Follow these steps to replace the lamp.
Turn off the projector and unplug the AC power cord.
Let the projector cool for at least 45 minutes.
Loosen the two (2) screws that secure the lamp. Lift
the lamp out of the projector by using the handle.
1
3
Replace the lamp with a new one and secure the two
(2) screws. Make sure that the lamp is set properly.
Close the lamp cover and secure the screw.4
Remove the screw and open the lamp cover.
Connect the AC power cord to the projector and turn
on the projector.
6Reset the lamp counter .
See “Resetting the Lamp Counter” on the next page.
5
Handle
Screw
Lamp Cover
Press here and pull upward.
Screw
Lamp
Screw
WARNING:
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER
Note:
The Lamp replacement icon will not appear when the Display function
is set to Off (p.49), during "Freeze" (p.28), or "No show" (p.29).
68
Maintenance and Cleaning
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee
of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time
than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of
the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETy PRECAUTIONS SHOULD BE TAKEN .
If a lamp explodes, disconnect the projector ’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
LAMP HANDLING PRECAUTIONS
Resetting the Lamp Counter
Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP
REPLACE indicator stops lighting and the Lamp replacement icon disappears.
Note:
Do not reset the Lamp counter without implementing
lamp replacement. Be sure to reset the Lamp counter
only after replacing the lamp.
Lamp counter Reset?
appears.
Select yes , then another
confirmation box appears.
Select yes again to reset
the Filter counter.
Press the MENU button to display the On-Screen
Menu. Use the Point
▲▼ buttons to select Setting and
then press the Point
► or the SELECT button.
Use the Point ▲▼ buttons to select Lamp counter
and then press the SELECT button. Use the Point
▲▼
buttons to select
Lamp counter reset and then press
SELECT button.
Lamp counter Reset? appears.
Select yes to continue.
1
Another confirmation dialog box appears, select yes to
reset the Filter counter.3
69
Lamp counter Reset?
appears.
Select Yes, then another
confirmation box appears.
Problem: – Solutions
– Plug the power cord of the projector into the AC outlet.
–
See if the POWER indicator lights red.
–
Wait until the POWER indicator stops blinking to turn on the projector
again. The projector can be turned on after the POWER indicator
turns red. See page 21.
–
Check the WARNING indicator. If the WARNING indicator lights red,
pro\
jector cannot be turned on. See page 64.
–
Check the projection lamp. See page 67.
–
Unlock the Key lock function for the projector. See page 59.
– Make sure Off or Countdown off is not chosen at display
func\
tion. See page 49.
– Make sure User or Off is not chosen at Logo (select)
function. See page 50.
– Make sure Input search function is adjusted properly. See page 48.
– That is the Filter warning icon. See page 62.
– That is the Lamp replacement icon or the Filter warning icon. See
pages 61, 62.
– Adjust focus of the projector. See page 26.
–
Provide proper distance between the projector and the projection
screen. See page 16.
–
Check the projection lens to see if it needs cleaning. See page 66.
–
Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. In such cases, leave
the projector off and wait until condensation evaporates.
– Check the Ceiling/Rear function. See page 53.
– Check the Ceiling function. See page 53.
– Check if the Contrast or Brightness are adjusted properly. See
pages 37, 44.
– Check if
Image mode is selected properly. See pages 36, 43.
– Check the lamp control function. See pages 28, 58.
–
Check the LAMP REPLACE indicator. If it lights, the end of lamp life
is approaching. Replace the lamp with a new one promptly. See page
67.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the i\
tems below once again.
– Make sure you have properly connected the projector to peripheral equipm\
ent as described on pages 17-19.
–
Make sure all equipment is connected to AC outlet and the power is turned on.
–
When the projector does not project an image from the connected computer\
, restart the computer.
No power
The initial display is not shown.
The initial display is not same
as the default set.
Input signal switches automatically.
(or does not switch automatically)
When the projector is on and you
press the input button, an icon
other than the Lamp mode icon
appears.
An icon other than Input mode or
Lamp mode icon appears.
Image is out of focus.
Image is Left/Right reversed.
Image is Top/Bottom reversed.
Picture is not bright enough.
70
Appendix
– Check the connection between your computer or video equipment
and the projector. See pages 17-19.
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to a projector. See your computer’s instruction
manual for the setting.
– It takes about 30 seconds to display an image after turning on the
projector. See page 21.
–
Check the Input signal, color system, video system or computer
system mode.
– Make sure the temperature is not out of the specified Operating
Temperature (
41˚F–95˚F [5˚C–35˚C]).
– When No Show function is operating, the image cannot be displayed.
Press the NO SHOW button or any other button on the remote control.
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 27.
– Press the Mute button. See page 27.
– When the AUDIO OUT is plugged-in, the projector's built-in speaker
is not available.
– Is the image projected? You will hear the sound only when the image
is projected.
– Check the Input signal, color system, video system or computer
system mode.
– Make sure
Blackboard is not selected on Image select
menu. See pages 36, 43.
– Check the Display function. See page 49.
– Check the Input signal. Auto PC adj.function can not work when
480p, \
575p, 70p, 480i, 575i, 1035i or 1080i is selected .
See page 33.
– The icon is not available in grayout when the digital signal is input.
– Make sure you selected Store after adjusting setting. Some settings
can not be stored if not registered with Store. See page 38, 45.
– Power management function can not work while Freeze or No
Show function is running. See page 56.
– Check the connection and the input signal to see if there is signal.
– Make sure Off is not selected at any function of "Auto setup".
See page 48.
– Make sure
On is not selected at the Ceiling function. See page 53.
– Make sure the Auto keystone function is not set to
Manual. Press
the AUTO SETUP/CANCEL button on the top control. See pages 26,48.
No image
No sound
The color is strange .
Some displays are not seen during
the operation .
Auto PC adjustment function does
not work .
The setting does not remain after
turning off power .
Power management does not work .
Capture function does not work .
Auto setup does not work properly .
Auto keystone function does not
work even when the projector is
tipped .
Appendix