Schwinn A10 Manual

							ASSEMBLY MANUAL / OWNER’S MANUAL  
Manual en Español Latino Americano:
http://www.schwinnfitness.com  
						

							2
Important Safety Instructions - Assembly 3
  Safety Warning Labels / Serial Number  4
Specifications 4
Before Assembly  5
Parts 6
Hardware 7
Tools 7
Assembly 8
Leveling the Bike  13
Moving the Bike  13Important Safety Instructions - Owner’s 
14
Features 15
  Console Features  16
  Contact Heart Rate (CHR)  17
Operations 19
 Adjustments  19
  Quick Start / Manual Program  19
  Profile Programs  20
  Pausing or Stopping  20
 Results  20
Changing Unit Measures   (English Imperial/Metric)  20
Maintenance 21
Troubleshooting 24
Warranty 27
Nautilus, Inc., (800) NAUTILUS / (800) 628-8458, www.NautilusInc.com - Customer Service: North America (800) 605-3369, 
[email protected] | outside U.S. +01-360-859-5180, [email protected]\
m | © 2013 Nautilus, Inc..
T ABLE Of CONTENTS
To validate warranty support, keep the original proof of purchase and record the following information:
Serial Number __________________________
Date of Purchase ____________________
To register your product warranty , go to: www.SchwinnFitness.com/register
Or call 1 (800) 605–3369.
If you have questions or problems with your product, please call 1 (800) NAUTILUS (628–8458)
Or go to: www.SchwinnFitness.com  
						

							3
IMpORTANT SAfETY INSTRUCTIONS 
— ASSEMBLY
!This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
!Read and understand all warnings on this machine.
Carefully read and understand the Assembly instructions.
•	 Keep	bystanders	and	children	away	from	the	product	you	are	assembling	at	all	times.
•	 Do	not	connect	power	supply	to	the	machine	until	instructed	to	do	so.
•	 Do	not	assemble	this	machine	outdoors	or	in	a	wet	or	moist	location.
•	 Make	sure	assembly	is	done	in	an	appropriate	work	space	away	from	foot	traffic	and	exposure	to	bystanders.
•	 Some	components	of	the	machine	can	be	heavy	or	awkward.	Use	a	second	person	when	doing	the	assembly	steps	 involving	these	parts.	Do	not	do	steps	that	involve	heavy	lifting	or	awkward	movements	on	your	own.
•	 Set	up	this	machine	on	a	solid,	level,	horizontal	surface.
•	 Do	not	try	to	change	the	design	or	functionality	of	this	machine.	This	could	compromise	the	safety	of	this	machine	 and will void the warranty.
•	 If	replacement	parts	are	necessary,	use	only	genuine	Nautilus
® replacement parts and hardware. Failure to use 
genuine replacement parts can cause a risk to users, keep the machine from operating correctly and void the 
warranty.
•	 Do	not	use	until	the	machine	has	been	fully	assembled	and	inspected	for	correct	performance	in	accordance	with	the	 Manual.
•	 Read	and	understand	the	complete	Manual	supplied	with	this	machine	before	first	use.	Keep	the	Manual	for	future	 reference.
•	 Do	all	assembly	steps	in	the	sequence	given.	Incorrect	assembly	can	lead	to	injury	or	incorrect	function.
•	 This	product	contains	magnets.	Magnetic	fields	can	interfere	with	the	normal	use	of	certain	medical	devices	at	a	close	 range.	 Users	may	come	 into	proximity	 of	the	 magnets	 in	the	 assembly,	 maintenance,	 and/or	use	of	the	 product.	 Given	
the obvious importance of these devices, such as a pacemaker, it is important that you consult with your medical 
provider in connection with the use of this equipment. Please consult the \
“Safety Warning Labels and Serial Number” 
section to determine the location of the magnets on this product.  
						

							4
SAfETY WARNINg LABELS ANd SERIAL NUMBER
FCC Compliance
!Changes	or	modifications	to	this	unit	not	expressly	approved	by	the	party	responsible	for	compliance	could	void	the	
user’s authority to operate the equipment.
The power supply complies with part 15 of the FCC rules. Operation is su\
bject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.
Note:    This power supply has been tested and found to comply with the limits fo\
r a Class B digital device, pursuant to Part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate \
radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does\
 cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures:
•		Reorient	or	relocate	the	receiving	antenna.
•		Increase	the	separation	between	the	equipment	and	receiver.
•			 Connect	the	equipment	into	an	outlet	on	a	circuit	different	from	that	to	which	the	receiver	is	connected.
•			 Consult	the	dealer	or	an	experienced	radio/TV	technician	for	help.
•
•
•
•
•
•
•
•
• •
•
•
Serial number
Product 
specification  
						

							5
SpECIfICATIONS
27.5” (67cm)19” (48cm)50” (126cm)
Before Assembly 
Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a 
hard,	level	surface.	Allow	a	workout	area	of	a	minimum	67”	x	56”	(1.7m	x	1.42m).
Basic Assembly Tips
Follow these basic points when you assemble your machine:
1.   
Read and understand the “Important Safety Instructions” before assembly.
2.    Collect all the pieces necessary for each assembly step.
3.    Using the recommended wrenches, turn the bolts and nuts to the right (clockwise) to tighten, and the left\
 (counter -
clockwise) to loosen, unless instructed otherwise.
4.    When attaching 2 pieces, gently lift and look through the bolt holes to help insert the bolt through the holes.
5.  The assembly can require 2 people. Maximum User Weight:   275 lbs. (125 kg)
Power Requirements:			 4	D	Batteries	(LR20)	–	not	included 
Operational	Voltage:		6VDC
Regulatory Approvals:
    Optional AC Power Adapter:  UL listed, CSA certified (or 
equivalent),	Rated	120V	60Hz	Input,	9VDC,	500mA	Output.	
Class 2 or LPS.
!  This product, its packaging, and components contain 
chemicals known to the State of California to cause 
cancer, birth defects, or reproductive harm. This Notice 
is provided in accordance with California’s Proposition 
65. If you would like additional information, please refer 
to our website at www.nautilus.com/prop65.  
						

							6
pARTS
Item QtyDescription ItemQtyDescription
1 1Main Frame 81Console
2 1Front Stabilizer 91Handlebars
3 1Rear  Stabilizer 101Left Pedal (L)
4 1Seat Post 111Right Pedal (R)
5 1Adjustment	Knob	(pre-installed) 121Water Bottle Holder
6 1Seat 131Media Tray
7 1Console Mast (with pre-installed Handlebar Bracket)
  Note:   Media Cable is attached to the Console.
1
5
8
96
2 3
4
10 (L) 11 (R)
12
7
13  
						

							7
To o l s
Included      Not Included
6 mm
ItemQtyDescription
A 4Carriage	Bolt	M8	x	65
B 8Arc Washer M8
C 4Acorn Nut M8
D 4Hex	Screw	M8	x	15
A BC D
(recommended)
HARdWARE / TOOLS
13mm/17mm
15 mm  
						

							8 1.  Attach Stabilizers to Main Frame
 
Note:   Make sure the Schwinn® decal on the Rear Stabilizer faces outward from the machine.
2.  Install Pedals
  Note:   The Left Pedal is reverse-threaded.  Be sure to attach Pedals on the proper side of the Bike. Orientation 
is based from a seated position on the bike. The Left Pedal has an “L”, the Right Pedal an “R”.
ASSEMBLY
X4
A 2
1
3
C B
X4
10 (L)
11 (R)  
						

							9
3. Attach Seat to Seat Post and Frame
 
Note:
   Hardware is pre-installed on Seat and not on Hardware Card. 
 N OTI C E :    The	Adjustment	Knob	is	pre-installed	on	the	Main	Frame.	Make	sure	the	Adjustment	Knob	engages	the	Seat 	
Post.
 
!Do	not	set	the	Seat	Post	position	higher	than	the	stop	mark	(MAX)	on	the	tube.
54X3
4. Install Console Mast on Main Assembly
 N OTI C E : 			Align	the	clips	on	the	cable	connectors	and	make	sure	the	connectors	lock.	Do	not	crimp	Console	Cable.
X4
B D
6mm
7  
						

							10 5. Install Handlebars on Console Mast
 Note:  Hardware is pre-installed on Console Mast and not on Hardware Card.
  N OTI C E :    Make sure the Handlebar Bracket (7a) has an equal distance between the two ends of the bracket and the 
bracket mount on the Console Mast.   
 
Do	not	crimp	the	cables. 	
9a
X2
6mm
9
=
=
7a
7