Schwinn A10 Manual

ASSEMBLY MANUAL / OWNER’S MANUAL  
Manual en Español Latino Americano:
http://www.schwinnfitness.com  

2
Important Safety Instructions - Assembly 3
  Safety Warning Labels / Serial Number  4
Specifications 4
Before Assembly  5
Parts 6
Hardware 7
Tools 7
Assembly 8
Leveling the Bike  13
Moving the Bike  13Important Safety Instructions - Owner’s 
14
Features 15
  Console Features  16
  Contact Heart Rate (CHR)  17
Operations 19
 Adjustments  19
  Quick Start / Manual Program  19
  Profile Programs  20
  Pausing or Stopping  20
 Results  20
Changing Unit Measures   (English Imperial/Metric)  20
Maintenance...

3
IMpORTANT SAfETY INSTRUCTIONS 
— ASSEMBLY
!This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
!Read and understand all warnings on this machine.
Carefully read and understand the Assembly instructions.
•	 Keep	bystanders	and	children	away	from	the	product	you	are	assembling	at	all	times.
•	 Do	not	connect	power	supply	to	the	machine	until	instructed	to	do	so.
•	 Do	not	assemble	this	machine	outdoors	or	in	a	wet...

4
SAfETY WARNINg LABELS ANd SERIAL NUMBER
FCC Compliance
!Changes	or	modifications	to	this	unit	not	expressly	approved	by	the	party	responsible	for	compliance	could	void	the	
user’s authority to operate the equipment.
The power supply complies with part 15 of the FCC rules. Operation is su\
bject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.
Note:...

5
SpECIfICATIONS
27.5” (67cm)19” (48cm)50” (126cm)
Before Assembly 
Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a 
hard,	level	surface.	Allow	a	workout	area	of	a	minimum	67”	x	56”	(1.7m	x	1.42m).
Basic Assembly Tips
Follow these basic points when you assemble your machine:
1.   
Read and understand the “Important Safety Instructions” before assembly.
2.    Collect all the pieces necessary for each assembly step.
3.    Using the...

6
pARTS
Item QtyDescription ItemQtyDescription
1 1Main Frame 81Console
2 1Front Stabilizer 91Handlebars
3 1Rear  Stabilizer 101Left Pedal (L)
4 1Seat Post 111Right Pedal (R)
5 1Adjustment	Knob	(pre-installed) 121Water Bottle Holder
6 1Seat 131Media Tray
7 1Console Mast (with pre-installed Handlebar Bracket)
  Note:   Media Cable is attached to the Console.
1
5
8
96
2 3
4
10 (L) 11 (R)
12
7
13  

7
To o l s
Included      Not Included
6 mm
ItemQtyDescription
A 4Carriage	Bolt	M8	x	65
B 8Arc Washer M8
C 4Acorn Nut M8
D 4Hex	Screw	M8	x	15
A BC D
(recommended)
HARdWARE / TOOLS
13mm/17mm
15 mm  

8 1.  Attach Stabilizers to Main Frame
 
Note:   Make sure the Schwinn® decal on the Rear Stabilizer faces outward from the machine.
2.  Install Pedals
  Note:   The Left Pedal is reverse-threaded.  Be sure to attach Pedals on the proper side of the Bike. Orientation 
is based from a seated position on the bike. The Left Pedal has an “L”, the Right Pedal an “R”.
ASSEMBLY
X4
A 2
1
3
C B
X4
10 (L)
11 (R)  

9
3. Attach Seat to Seat Post and Frame
 
Note:
   Hardware is pre-installed on Seat and not on Hardware Card. 
 N OTI C E :    The	Adjustment	Knob	is	pre-installed	on	the	Main	Frame.	Make	sure	the	Adjustment	Knob	engages	the	Seat 	
Post.
 
!Do	not	set	the	Seat	Post	position	higher	than	the	stop	mark	(MAX)	on	the	tube.
54X3
4. Install Console Mast on Main Assembly
 N OTI C E : 			Align	the	clips	on	the	cable	connectors	and	make	sure	the	connectors	lock.	Do	not	crimp	Console	Cable.
X4
B D
6mm
7  

10 5. Install Handlebars on Console Mast
 Note:  Hardware is pre-installed on Console Mast and not on Hardware Card.
  N OTI C E :    Make sure the Handlebar Bracket (7a) has an equal distance between the two ends of the bracket and the 
bracket mount on the Console Mast.   
 
Do	not	crimp	the	cables. 	
9a
X2
6mm
9
=
=
7a
7