Sharp Xv Z2000 Projector User Manual

							-30
Image Projection
ZOOM/FOCUS 
button
Adjustment buttons
('/"/\/|)
Adjustment
buttons ('/"/\/|)
ZOOM/FOCUS
button
Adjusting the Focus
1Press  on the remote control.
2Press \ or | on the remote con-
trol to adjust the focus.
Note
•You can also adjust the focus by using
 and \ \\ \
\ or | || |
| on the projector.
Adjusting the Projected Image Size
1Press  on the remote control.
2Press ' or " on the remote con-
trol to adjust the zoom.
Note
•You can also adjust the zoom by using
 and ' '' '
' or " "" "
" on the projector.
XV-Z2000U_E_P28_35.p6504.10.13, 0:16 PM 30 
						

							-31
Basic Operation
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet at the front and rear
of the projector when the screen is located
higher than the projector, the screen is inclined
or when the installation site is slightly inclined.
Install the projector so that it is as perpen-
dicular to the screen as possible.
1Lift the projector to adjust its
height while pressing the
HEIGHT ADJUST button.
•The projector is adjustable up to approxi-
mately 12 degrees (6 steps).
•When lowering the projector, it may be
difficult to move the front adjustment foot
because the installation surface is diffi-
cult to slide. In this case, pull the pro-
jector back slightly and adjust its height.
2Remove your hands from the
HEIGHT ADJUST button of the
projector after its height has
been finely adjusted.
3Finely adjust the height and in-
clination by turning the rear ad-
justment feet.
Note
•When adjusting the projected image position,
trapezoidal distortion occurs. In this case, see
“Keystone Correction” on page 32.
Info
•Do not press the HEIGHT ADJUST button
when the front adjustment foot comes out
without firmly holding the projector.
•Do not hold the lens when lifting or lower-
ing the projector.
•When lowering the projector, be careful not
to get your fingers caught in the area be-
tween the adjustment foot and the projector.
Side View
Lens 
center
Top View
Front
adjustment foot
HEIGHT ADJUST button
Rear adjustment feet
XV-Z2000U_E_P28_35.p6504.10.13, 0:16 PM 31 
						

							-32
"On-screen Display (Keystone Correction mode)
KEYSTONE
button
UNDO
buttonAdjustment
buttons (
'/"/\/|)
Horizontal Keystone Correction
Vertical Keystone Correction
Note
•When adjusting the Keystone setting, the placement
range is changed depending on the input signal
type.
•Keystone correction cannot be applied to On-screen
Display.
•When Keystone correction is applied, the resolution
of image can be deteriorated to some extent.
•Keystone Correction is also returned to the factory
preset settings by pressing 
 on the remote
control.
Keystone Correction
This function can be used to adjust the Keystone
settings.
Note
•When the image is projected from a di-
rection at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is called
Keystone Correction.
1Press  on the remote control
to enter the Keystone Correction
mode.
2Press '/" to select “H Keystone”
or “V  Keystone”.
3Press \/| to move the  mark on
the selected adjustment item to
the desired setting.
Note
•Straight lines and the edges of the dis-
played image may appear jagged,
when adjusting the Keystone setting.
•When adjusting “H Keystone” and “V
Keystone” at the same time, the
values of adjustable angles for each
setting become smaller.
•The adjustable value of the “V Key-
stone” becomes extremely small
when “H Keystone” is made to be the
maximum value.
•Keystone correction is disabled while
the picture mode is set to “SMART
STRETCH”. (See page 35.)
4Press .
•The on-screen display of the Keystone
Correction mode will disappear.
Description
Horizontally adjusts the
keystone settings.
Vertically adjusts the keystone
settings.
Returns to the factory preset
settings.
Selectable
items
H Keystone
V Keystone
Reset
Image Projection
XV-Z2000U_E_P28_35.p6504.10.13, 0:17 PM 32 
						

							-33
Basic Operation
Placement of the Projected Image
Using the Keystone Correction
Place the projector at a distance from the screen that
allows images to be projected onto the screen by referring
to “Screen Size and Projection Distance” on page 17.
: Screen area
Note
•The aspect ratio of the projected image also shifts
slightly when the “H Keystone” and “V Keystone”
functions are adjusted simultaneously.
•If you cannot correct trapezoidal distortion with
Keystone correction, change the placement
position of the projector.
1Project the test pattern of the
Keystone correction function onto
the screen. Adjust the focus until
the image on the screen comes
into focus. (See page 30.)
ZOOM/FOCUSEND ZOO
M
FOCUS
2Change the projection angle moving
the projector or using the adjuster to
properly project images onto the
screen. (See page 31).
3Align the edge of the screen closest
to the projector with the test pattern
by adjusting the zoom and the
adjsuter. (See pages 30 and 31.)
ZOOM/FOCUSEND ZOOM
FOCUS
Align
Align
4Adjust the Keystone function so that the
size of the projected image matches the
screen size. (See page 32.)
5Align the image on the screen by
adjusting the zoom function and
the adjsuter.
ZOOM/FOCUSEND ZOOM
FOCUS
6Adjust the focus so that the projected
image is in focus at the center of the
screen. (See page 30.)
XV-Z2000U_E_P28_35.p6504.10.13, 0:17 PM 33 
						

							-34
Selecting the Picture Mode
You can select the picture setting (Memory)
directly stored in “Picture Mode” on the
“Picture” menu.
Press  on the remote control.
•Each time the button is pressed while the display
is on, the picture mode changes in order of:
Memory OFF Memory 1 Memory 2
Memory 5 Memory 4 Memory 3
Note
•This function can also be accessed from the
OSD menu (see page 44).
Switching the High Bright-
ness / High Contrast Mode
This function controls the quantity of the pro-
jected light and the contrast of the image.
Press  on the remote control.
•Each time the button is pressed while the display is on,
the mode is switched between “HIGH BRIGHTNESS
MODE” and “HIGH CONTRAST MODE”.
Note
•This function can also be accessed from the
OSD menu (see page 44).
Adjusting the Picture
Aspect Ratio
This function allows you to modify or
customize the picture display mode to enhance
the input image. Depending on the input signal,
you can choose STRETCH, SIDE BAR, SMART
STRETCH or CINEMA ZOOM image.
Press  on the remote control.
•Each time  is pressed, the picture mode
changes as shown on the next page.
•
To return to the standard image (“STRETCH”), press
 while “RESIZE” is displayed on the screen.
•You can also change the picture display mode
by pressing 
 on the projector.
PICTURE MODE
button
IRIS button
UNDO
button
RESIZE
button
Image Projection
RESIZE button
UNDO button
XV-Z2000U_E_P28_35.p6504.10.13, 0:17 PM 34 
						

							-35
Basic Operation
480I480P
576I576P
NTSC
PAL
SECAM
540P
1080
I
720P
VGA
SVGA
XGA
Input signal
SIDE BAR SMART STRETCHOutput screen image
STRETCH CINEMA ZOOM
4:3 aspect ratio
Letterbox
16:9 aspect ratio
16:9 aspect ratioSqueeze
16:9 aspect ratio
4:3 aspect ratio
Note
•“SMART STRETCH” cannot be selected while the Keystone correction (page 32) is being adjusted.
•Keystone correction (page 32) is disabled while the picture mode is set to “SMART STRETCH”.
•580
I/580P is displayed on the screen when signal 576I/576P is input.
•“STRETCH” is fixed when 540P, 720P or 1080
I signal is entered.
•“SMART STRETCH” cannot be selected while input signal from a computer (VGA, SVGA or XGA) is
entered.
XV-Z2000U_E_P28_35.p6504.10.13, 0:17 PM 35 
						

							-36
Menu Items
The following shows the items that can be set in the projector.
Note
•“Tint” cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60.
•“Color”, “Tint”, “Sharp”, “Clock”, “Phase”, “H-Pos”, “V-Pos” and “Auto Sync” cannot be used in the DIGITAL
mode.
•“Fine Sync” menu cannot be displayed in the INPUT 3 and INPUT 4 modes.
“Picture” menu
“Fine Sync” menu
Example: Screen for INPUT 1
mode
+30 -30
+30 -30
+30 -30
+30 -30
+30 -30
+30 -30
Tint Color
Sharp Bright
+30 -30Contrast
Red
Blue
Reset Picture
IRISHigh Brightness
High Contrast
5500K
6500K
7500K
8500K
9300K
10500K
Main Menu Sub Menu
CLR Temp
Page 42
Page 42
Page 42
Page 43
Page 43
Page 44
Page 44
*1
*1
*1
*1: Items when selecting INPUT 1, 2, 3, 4 or when inputting component signal 
 through INPUT 5
Standard
Cinema 1
Cinema 2
Cinema 3 Gamma Adj.
Bright Boost   [ON/OFF]
Picture ModeMemory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory OFF10 0
3 -33 -33 -33 -3
10 010 010 010 010 0
Fine Sync
+15 -15
+30 -30
+30 -30
+30 -30Clock
Phase
H-Pos
V-Pos
Reset
Signal Info Special Modes
Main Menu
Auto Sync [ON/OFF]
Page 45 Page 45
Page 45
Page 46
Page 46
*2 *2 *2
*2: Item when inputting RGB signal through INPUT 5
Example: Screen for INPUT 5
(RGB) mode
Example: Screen for INPUT 5
(RGB) mode
XV-Z2000U_E_P36_37.p6504.10.13, 0:17 PM 36 
						

							-37
Useful Features
“Options” menu
“Language” menu
Lamp Timer (Life)
Options
Main Menu Sub Menu
OSD Display [ON/OFF]
Auto
PAL
NTSC3.58
SECAM
NTSC4.43
PAL-M
PAL-N
PAL-60 Video System
Background [Blue/None]
Eco Mode [Eco/Standard]
Auto Power Off [ON/OFF]
Center
Upper Right
Lower Right
Upper Left
Lower Left Menu Position
Page 47
Page 47 Page 47
Page 48
Page 49
Page 49
Page 50
Page 50
Page 51
*1
*2
*1: Item when selecting INPUT 3 or INPUT 4
*2: Item when selecting INPUT 5
RGB
Component Signal Type
Menu Color [Opaque/Translucent]
Page 48
Main Menu
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
PortuguêsLanguagePage 52
“PRJ Mode” menu
PRJ Mode
Front
Ceiling+Front
Rear
Ceiling+RearPage 52
Main Menu
Example: Screen for INPUT 1
mode
Example: Screen for INPUT 4
mode
XV-Z2000U_E_P36_37.p6504.10.13, 0:17 PM 37 
						

							-38
Using the Menu Screen
Menu icons
Adjustment
buttons ('/"/\/|)
ENTER
buttonMENU
button
UNDO
buttonENTER button
MENU button
UNDO button Adjustment buttons
('/"/\/|)
Example: “Picture” menu screen for
INPUT 1 mode The menu can be operated to achieve two functions, adjustments and settings. (For setting
the menu items, see pages 40 and 41. )
Menu Selections
(Adjustments)
•This operation can also be performed by using the
buttons on the projector.
1Press .
•The “Picture” menu screen for the selected
input mode is displayed.
2Press 
| || |
| or 
\ \\ \
\ to display the other
menu screens.
•The menu icon for the selected menu screen
is highlighted.
Note
•The “Fine Sync” menu is not available for
selecting INPUT 3 or 4.
Menu icon Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
XV-Z2000U_E_P38_46.p6504.10.13, 0:18 PM 38 
						

							Useful Features
-39
3Press 
' '' '
' or 
" "" "
" to select the item you
want to adjust.
•The selected item is highlighted.
(Example: Selecting “Bright”)
To adjust the projected
image while viewing it
Press .
•The selected single adjustment item (e.g.
“Bright”) appears on the lower part of the
screen.
•When pressing ' or ", the next item will
be displayed. (e.g. “Bright” is replaced with
“Color” by pressing  ".)
Note
•Press  to return to the previous screen.
4Press 
| || |
| or 
\ \\ \
\ to adjust the item se-
lected.
•The adjustment is stored.
5Press .
•The menu screen will disappear.
Single
adjustment
items
XV-Z2000U_E_P38_46.p6504.10.13, 0:18 PM 39