Sharp Xv Z20000 Projector User Manual

XV-Z20000/
DT-5000
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS 

ENGLISH
-1
Before using the projector, please read this operation manual carefully.
WARNING:  High brightness light source. Do not stare into the beam of light, or view directly. Be especially 
careful that children do not stare directly into the beam of light.
WARNING:To reduce the risk of fi re or electric shock, do not expose this product to rain 
or mois ture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED...

-2
Caution Concerning Lamp Replacement
See “Regarding the Lamp” on page 48.
PRODUCT DISPOSALThis projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of 
these materials may be regulated due to environmental considerations. For disposal or recycling information, please 
contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: 
www.eiae.org.
This SHARP projector uses a DLP® chip. This...

-3
IntroductionContents
Preparing
Setup
Setting Up the Projector ...............................14Setting Up the Projector ...................................... 14
Standard Setup (Front Projection) ........................ 14
Projection (PRJ) Mode ......................................... 15
Ceiling-mount Setup ........................................... 15
Picture (Screen) Size and Projection Distance ...... 16
Connections
Samples of Cables for Connection ..............17
Connecting to Video Equipment...

-4
Accessories
Supplied accessories
Optional accessories
Remote control
• RRMCGA500WJSA
 for XV-Z20000
• RRMCGA500WJSB
for DT-5000Two AA size batteries
Lens cap (attached)
PCAPH1056CESAOperation manual Power cord
 (6' (1.8 m))
QACCDA007WJPZ
■ Lamp unit  AN-K20LP
■ 3 RCA to 15-pin D-sub cable (9'10" (3.0 m))  AN-C3CP2
■ DVI to 15-pin D-sub adaptor (7.9" (20 cm))  AN-A1DV 
■ DVI cable (9'10" (3.0 m))  AN-C3DV
Note
• Some of the optional accessories may not be available depending on...

-5
Introduction
1. Read InstructionsAll the safety and operating instructions should be read before 
the product is operated.
 2. Retain InstructionsThe safety and operating instructions should be retained for 
future reference.
3. Heed WarningsAll warnings on the product and in the operating instructions 
should be adhered to.
4. Follow InstructionsAll operating and use instructions should be followed.
5. CleaningUnplug this product from the wall outlet before cleaning. Do 
not use liquid cleaners or...

-6
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit■  Potential hazard of glass particles if lamp ruptures. 
In case of lamp rupture, contact your nearest Sharp 
Authorized Service Center or Dealer for replacement.
  See “Regarding the Lamp” on page 48.
Caution concerning the setup of the projector■  For minimal servicing and to maintain high image quality, 
SHARP recommends that this projector be installed in 
an area free from humidity, dust and...

-7
Introduction
Temperature monitor function
■  If the projector starts to overheat due to setup problems 
or blockage of the air vents, “” and “” will 
illuminate in the lower left corner of the picture. If the 
temperature continues to rise, the lamp will turn off, the 
temperature warning indicator on the projector will blink, 
and after a 90-second cooling-off period the projector 
will enter standby mode. Refer to “Maintenance Indica-
tors/Maintenance” on page 46for details.
Info
• The cooling fan...

-8
34
34
34
28
27
27
30
27
46
28
26
28
11
25
34
47
25, 46
25, 46
Numbers in  refer to the main pages in this operation manual where the topic is explained.
Projector
Part Names and Functions
3
21
1
3
Using the Terminal Cover
When the projector is used on a desktop, high mounted 
or ceiling mounted, attach the terminal cover (supplied) to 
hide the connecting cables.
Attaching the Terminal Cover
Align the hook on the terminal cover with the insert 
hole in the hook at the back of the projector.
Press the...

-9
Introduction
Projector (Rear View)
11
25
47
47
47
Terminals
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. 
Refer to the information that came with the system for instructions on how to use it to secure the projector.
Terminal Description Page
COMPONENT/RGB1, 2 terminals
Connecting video equipment with component output terminal (DVD player, etc.) or a com-
puter with analog RGB output terminal.
S-VIDEO...